diff --git a/meta-raspberrypi/.github/workflows/yocto-builds.yml b/meta-raspberrypi/.github/workflows/yocto-builds.yml
index 93f9f46..408d25e 100644
--- a/meta-raspberrypi/.github/workflows/yocto-builds.yml
+++ b/meta-raspberrypi/.github/workflows/yocto-builds.yml
@@ -25,6 +25,7 @@
           - raspberrypi3
           - raspberrypi4-64
           - raspberrypi4
+          - raspberrypi5
           - raspberrypi-cm3
           - raspberrypi-cm
           - raspberrypi-armv7
diff --git a/meta-raspberrypi/conf/machine/include/rpi-base.inc b/meta-raspberrypi/conf/machine/include/rpi-base.inc
index 472f18e..c87ab97 100644
--- a/meta-raspberrypi/conf/machine/include/rpi-base.inc
+++ b/meta-raspberrypi/conf/machine/include/rpi-base.inc
@@ -54,6 +54,7 @@
     overlays/vc4-fkms-v3d-pi4.dtbo \
     overlays/vc4-kms-v3d.dtbo \
     overlays/vc4-kms-v3d-pi4.dtbo \
+    overlays/vc4-kms-v3d-pi5.dtbo \
     overlays/vc4-kms-dsi-7inch.dtbo \
     overlays/w1-gpio.dtbo \
     overlays/w1-gpio-pullup.dtbo \
@@ -77,6 +78,7 @@
     bcm2710-rpi-cm3.dtb \
     bcm2711-rpi-cm4.dtb \
     bcm2711-rpi-cm4s.dtb \
+    bcm2712-rpi-5-b.dtb \
     "
 
 KERNEL_DEVICETREE ??= " \
diff --git a/meta-raspberrypi/conf/machine/raspberrypi-armv8.conf b/meta-raspberrypi/conf/machine/raspberrypi-armv8.conf
index 8d412ba..0128bdc 100644
--- a/meta-raspberrypi/conf/machine/raspberrypi-armv8.conf
+++ b/meta-raspberrypi/conf/machine/raspberrypi-armv8.conf
@@ -32,6 +32,7 @@
     broadcom/bcm2711-rpi-400.dtb \
     broadcom/bcm2711-rpi-cm4.dtb \
     broadcom/bcm2711-rpi-cm4s.dtb \
+    broadcom/bcm2712-rpi-5-b.dtb \
 "
 
 SDIMG_KERNELIMAGE ?= "kernel8.img"
diff --git a/meta-raspberrypi/conf/machine/raspberrypi5.conf b/meta-raspberrypi/conf/machine/raspberrypi5.conf
new file mode 100644
index 0000000..8c38637
--- /dev/null
+++ b/meta-raspberrypi/conf/machine/raspberrypi5.conf
@@ -0,0 +1,26 @@
+#@TYPE: Machine
+#@NAME: RaspberryPi 5 Development Board (64bit)
+#@DESCRIPTION: Machine configuration for the RaspberryPi 5 in 64 bits mode
+
+require conf/machine/include/arm/armv8-2a/tune-cortexa76.inc
+include conf/machine/include/rpi-base.inc
+
+MACHINE_FEATURES += "pci"
+MACHINE_EXTRA_RRECOMMENDS += "\
+    linux-firmware-rpidistro-bcm43455 \
+    bluez-firmware-rpidistro-bcm4345c0-hcd \
+    linux-firmware-rpidistro-bcm43456 \
+    bluez-firmware-rpidistro-bcm4345c5-hcd \
+"
+
+RPI_KERNEL_DEVICETREE = " \
+    broadcom/bcm2712-rpi-5-b.dtb \
+"
+
+SDIMG_KERNELIMAGE ?= "kernel_2712.img"
+SERIAL_CONSOLES ?= "115200;ttyAMA10"
+
+VC4DTBO ?= "vc4-kms-v3d"
+
+# "zImage" not supported on arm64 and ".gz" images not supported by bootloader yet
+KERNEL_IMAGETYPE_DIRECT ?= "Image"
diff --git a/meta-raspberrypi/docs/extra-build-config.md b/meta-raspberrypi/docs/extra-build-config.md
index 3d66ffd..dfb86f1 100644
--- a/meta-raspberrypi/docs/extra-build-config.md
+++ b/meta-raspberrypi/docs/extra-build-config.md
@@ -340,6 +340,13 @@
 
     CAN_OSCILLATOR="8000000"
 
+Configure the interrupt pin to the one connected to the CAN module. By default,
+the pins are set to 25 for can0 and 24 for can1. To change them to 12 and 16,
+the following variables also have to be set:
+
+    CAN0_INTERRUPT_PIN = "12"
+    CAN1_INTERRUPT_PIN = "16"
+
 Tested modules:
 
 * PiCAN2 (16 MHz crystal): <http://skpang.co.uk/catalog/pican2-canbus-board-for-raspberry-pi-23-p-1475.html>
diff --git a/meta-raspberrypi/recipes-bsp/bootfiles/rpi-config_git.bb b/meta-raspberrypi/recipes-bsp/bootfiles/rpi-config_git.bb
index ee0f407..b91668f 100644
--- a/meta-raspberrypi/recipes-bsp/bootfiles/rpi-config_git.bb
+++ b/meta-raspberrypi/recipes-bsp/bootfiles/rpi-config_git.bb
@@ -30,6 +30,8 @@
 GPIO_IR_TX ?= "17"
 
 CAN_OSCILLATOR ?= "16000000"
+CAN0_INTERRUPT_PIN ?= "25"
+CAN1_INTERRUPT_PIN ?= "24"
 
 ENABLE_UART ??= ""
 
@@ -268,12 +270,12 @@
     # ENABLE DUAL CAN
     if [ "${ENABLE_DUAL_CAN}" = "1" ]; then
         echo "# Enable DUAL CAN" >>$CONFIG
-        echo "dtoverlay=mcp2515-can0,oscillator=${CAN_OSCILLATOR},interrupt=25" >>$CONFIG
-        echo "dtoverlay=mcp2515-can1,oscillator=${CAN_OSCILLATOR},interrupt=24" >>$CONFIG
+        echo "dtoverlay=mcp2515-can0,oscillator=${CAN_OSCILLATOR},interrupt=${CAN0_INTERRUPT_PIN}" >>$CONFIG
+        echo "dtoverlay=mcp2515-can1,oscillator=${CAN_OSCILLATOR},interrupt=${CAN1_INTERRUPT_PIN}" >>$CONFIG
     # ENABLE CAN
     elif [ "${ENABLE_CAN}" = "1" ]; then
         echo "# Enable CAN" >>$CONFIG
-        echo "dtoverlay=mcp2515-can0,oscillator=${CAN_OSCILLATOR},interrupt=25" >>$CONFIG
+        echo "dtoverlay=mcp2515-can0,oscillator=${CAN_OSCILLATOR},interrupt=${CAN0_INTERRUPT_PIN}" >>$CONFIG
     fi
 
 
@@ -317,6 +319,13 @@
         echo "# Enable One-Wire Interface" >> $CONFIG
         echo "dtoverlay=w1-gpio" >> $CONFIG
     fi
+
+    # Reduce config.txt file size to avoid corruption and
+    # to boot successfully Raspberry Pi 5. The issue has
+    # been reported to related projects:
+    # https://github.com/raspberrypi/firmware/issues/1848
+    # https://github.com/Evilpaul/RPi-config/issues/9
+    sed -i '/^##/d' $CONFIG
 }
 
 do_deploy:append:raspberrypi3-64() {
diff --git a/meta-raspberrypi/recipes-bsp/u-boot/u-boot_%.bbappend b/meta-raspberrypi/recipes-bsp/u-boot/u-boot_%.bbappend
index e50acf5..78b3e48 100644
--- a/meta-raspberrypi/recipes-bsp/u-boot/u-boot_%.bbappend
+++ b/meta-raspberrypi/recipes-bsp/u-boot/u-boot_%.bbappend
@@ -12,3 +12,6 @@
     install -d ${D}${sysconfdir}
     install -m 0644 ${WORKDIR}/fw_env.config ${D}${sysconfdir}/fw_env.config
 }
+
+# Temporary avoid Raspberry Pi 5 because U-Boot has not been ported yet
+COMPATIBLE_MACHINE:raspberrypi5 = "(-)"
diff --git a/meta-raspberrypi/recipes-kernel/linux/linux-raspberrypi.inc b/meta-raspberrypi/recipes-kernel/linux/linux-raspberrypi.inc
index b77d1c4..e62ff3f 100644
--- a/meta-raspberrypi/recipes-kernel/linux/linux-raspberrypi.inc
+++ b/meta-raspberrypi/recipes-kernel/linux/linux-raspberrypi.inc
@@ -33,6 +33,7 @@
 KBUILD_DEFCONFIG:raspberrypi4-64 ?= "bcm2711_defconfig"
 KBUILD_DEFCONFIG:raspberrypi-armv7 ?= "bcm2711_defconfig"
 KBUILD_DEFCONFIG:raspberrypi-armv8 ?= "bcm2711_defconfig"
+KBUILD_DEFCONFIG:raspberrypi5 ?= "bcm2712_defconfig"
 
 LINUX_VERSION_EXTENSION ?= ""