Guard on BMC

Problem Description

On systems with multiple processor units and other redundant vital resources, the system downtime can be prevented by isolating the faulty components. This document discusses the design of the BMC support for such isolation procedures. The defective components can be kept isolated until a replacement. Most of the actions required to isolate the parts will be dependant on the architecture and taken care of by the host. But the BMC needs to support a few steps like notifying users about the components in isolation, clearing isolation, isolating a suspected part, or isolating when the host is down due to a severe fault. The process of isolation is mentioned as guard in this document, which means guarding the system from faulty components.

Glossary

Guard: Guarding the system against failures by permanently isolating faulty units.

Guard Records: A file in the persistent storage with the list of permanently isolated components.

Manual guard: An operation to manually add a unit to the list of isolated units. This operation is helpful in isolating a suspected component without physically removing it from the server.

Background and References

The guard in the servers is for managing a record of faulty components to keep them out of service. The list of faulty but guarded components can be stored in multiple locations based on the ownership of the component. How to store the record or manage the record will be decided by the respective component. Some of the examples are guard on motherboard components managed by the host, guard on the fans can be managed by the fan control application, or the guard on the power components can be managed by the power management application.

These records will be created when an error is encountered on an element that can be isolated. The decision to create a record is based on the type of error, usecase, and the availability of a redundant hardware resource to keep the system in a usable state. The record which gets created to isolate the component is named as Guard Record. The guard record will be deleted after a repair action or manually by service personnel. Most of the time, the host creates the guard record since the host is responsible for the initialization and use of the hardware resources in a server system. The BMC creates guard records on a limited set of units during the early boot time, after a severe fault, which brings the host down or on the components like a power supply or fan which can be controlled by BMC. The BMC retrieves the guard records for presenting to an external interface for the review of customers and service personnel form various guard record sources.

Requirements

Primary requirements

Guard Usecases

  • When user requests, create a record in the right guard record repository, based on the hardware component.
  • An option should be given to user to create guard record for DIMM and Processor core to manually keep it out of service.
  • An option should be given to the user to delete a guard record.
  • An option should be given to list the guard records.
  • An option should be given to delete all guard records
  • Industry standard interfaces should be provided to carry out these operations on the guard records.

Assumptions

  • The guard records on the units which are owned by the host will be applied only in a subsequent boot.
  • The sub-system which owns the hardware resource will apply the guard record and isolates the units.
  • The clearing of the records after the replacement of the faulty component should be done by the component owning the guard records.
  • There should be a mapping between key in the guard record to the key used in BMC for the components.

Proposed Design

The guard proposed here is an aggregator for the guard records from various sources and provide a common interface for creating, deleting and listing those records.

D-Bus Interfaces

On BMC, There will be a guard manager object and objects for each entry.

Guard Manager

Guard manager is for providing the external interfaces for managing the guard records and retrieving information about guard records. The methods and properties of the guard manager.

  • Create Guard: Create guard record for a DIMM or Processor core Inputs: - Inventory path of the DIMM or Processor core to be guarded.

  • Delete Guard: Delete an existing guard record Deleting the guard record D-Bus entry should delete the underlying record.

  • Clear all guard: Clear all guard records in the system.

  • List Guard: List all the guarded components.

Note: In few platforms may be the system or hardware is not in a state where guard operation can be performed either "permanently" or "temporarily".

Guard Entry

The properties of each guard entry will be part of this object Properties:

  • ID: Id of the record which is part of the entry object path.
  • Associations:
    • Guarded hardware inventory path:
      • Forward Name must be "isolated_hw".
      • Reverse Name must be "isolated_hw_entry".
    • BMC Error Log:

      • Forward Name must be "isolated_hw_errorlog".

      • Reverse Name must be "isolated_hw_entry".

        Error Log association can be optional because a user may be tried guard hardware and it is not an error case.

  • Severity: Type of Guard
    • Manual - Manually Guarded
    • Critical - Guarded based on a critical error
    • Warning - Guarded based on an error which is not critical, but eventually, there can be critical failures.
  • Resolved: Status of guarded hardware

    • Used to indicate whether guarded hardware is repaired or replaced.

      Note: Setting this to "true" will not delete this entry because in a few system platforms guarded hardware records may not be deleted and used for further analysis.

The underlying guard function is implemented by the applications managing the hardware units. The application which implements the common guard entry interface should map between entry to the underlying guard record in the original guard record store.

Redfish interface

Manual guard

Creating manual gurad record, set the "Enabled" property to "false" to manually guard a unit which is present in the inventory.

redfish » v1 » Systems » system » Processors » CPU1

{
  "@odata.type": "#Processor.v1_7_0.Processor",
  "Id":view details "CPU1",
  "Name": "Processor",
  "Socket": "CPU 1",
  "ProcessorType": "CPU",
  "ProcessorId":
   {
       "VendorId": "XXXX",
       "IdentificationRegisters": "XXXX",
   } ,
   "MaxSpeedMHz": 3700,
   "TotalCores": 8,
   "TotalThreads": 16,
   "Status":
   {
        "State": "UnavailableOffline",
        "Health": "Critical"
        "Enabled": "False" <--- guarded a CPU1
   } ,
   "@odata.id":view details "/redfish/v1/Systems/system/Processors/CPU1"
}

Listing the guard record

redfish >> v1 >> Systems >> system >> LogServices >> IsolatedHardware

>> Entries

{
  "@odata.id": "/redfish/v1/Systems/system/LogServices/IsolatedHardware/Entries",
  "@odata.type": "#LogEntryCollection.LogEntryCollection",
  "Description": "Collection of Isolated Hardware Components",
  "Members": [
    {
      "@odata.id":
"/redfish/v1/Systems/system/LogServices/IsolatedHardware/Entries/1",
      "@odata.type": "#LogEntry.v1_7_0.LogEntry",
      "Created": "2020-10-15T10:30:08+00:00",
      "EntryType": "Event",
      "Id": "1",
      "Resolved": "false",
      "Name": "Processor 1",
      "links":  {
                 "OriginOfCondition": {
                        "@odata.id": "/redfish/v1/Systems/system/Processors/cpu1"
                  }
                },
      "Severity": "Critical",
      "SensorType" : "Processor",
      "AdditionalDataURI": “/redfish/v1/Systems/system/LogServices/EventLog/attachement/111"
      “AddionalDataSizeBytes": "1024"
    }
  ],
  "Members@odata.count": 1,
  "Name": "Isolated Hardware Entries"
  }

Alternatives Considered

The guard records can be created for any components which are redundant and isolatable to prevent any damage to the hardware or data. Once the record is created, an isolation procedure is needed to isolate the units from service. Some of the units like which are controlled by the host can be isolated only after a reboot, but the units controlled by BMC can be immediately taken out of service. The alternatives are

  • The host creates, applies, and present guard records: In this case, BMC has no control, and the host needs to provide the user interface, so there may not be a common interface across different types of hosts. Different user interfaces are required for guard records created by BMC and host.
  • BMC manages the external interfaces for guard: There will be one common point for presenting or managing the guard records created by multiple hosts or BMC itself. There are some guard records created after a severe failure in the host; as a system control entity, it will be easier for BMC to handle such situations and create the records.

Impacts

  • The guard records will be presented as an extension to logs
  • Redfish implementation will have an impact to do the operations required for the guard record management by the user. A request for standardization is planned for the method to list the isolated units in the redfish since that is not yet available in the redfish standard.

Testing

The necessary tests needed are creating, deleting, and listing the guard records and that should be automated, further tests on the isolation of each type of the unit is implementation-specific.