commit	9dd93cfa7309ed5fd97c47a302dc1e2d227b526e	[log] [tgz]
author	Cyril Bur <cyril.bur@au1.ibm.com>	Mon Jan 30 16:36:46 2017 +1100
committer	Cyril Bur <cyril.bur@au1.ibm.com>	Mon Feb 06 14:00:13 2017 +1100
tree	b5af8e7e5c613a42c6e05518c430637600c0b15b
parent	f0409b99d08d1b15329c714f2b9683645f08de10 [diff]

tree: b5af8e7e5c613a42c6e05518c430637600c0b15b

README.md

Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at

http://www.apache.org/licenses/LICENSE-2.0

Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License.

Intro

The autotools of this requires the autoconf-archive package for your system

This is a protocol description using the mailbox registers on Aspeed 2400/2500 chips for host to BMC communication. The mailbox consists of 16 (8 bit) data registers see Layout for their use. Mailbox interrupt enabling, masking and triggering is done using a pair of control registers, one accessible by the host the other by the BMC. Interrupts can also be raised per write to each data register, for BMC and host. Write tiggered interrupts are configured using two 8 bit registers where each bit represents a data register and if an interrupt should fire on write. Two 8 bit registers are present to act as a mask for write triggered interrupts.

General use

Messages usually originate from the host to the BMC. There are special cases for a back channel for the BMC to pass new information to the host which will be discussed later.

To initiate a request the host must set a command code (see Commands) into mailbox data register 0. It is also the hosts responsibility to generate a unique sequence number into mailbox register 1. After this any command specific data should be written (see Layout). The host must then generate an interrupt to the BMC by using bit 0 of its control register and wait for an interrupt in the response. Generating an interrupt automatically sets bit 7 of the corresponding control register. This bit can be used to poll for messages.

On receiving an interrupt (or polling on bit 7 of its Control Register) the BMC should read the message from the general registers of the mailbox and perform the necessary action before responding. On responding the BMC must ensure that the sequence number is the same as the one in the request from the host. The BMC must also ensure that mailbox data regsiter 13 is a valid response code (see Responses). The BMC should then use its control register to generate an interrupt for the host to notify it of a response.

BMC to host

BMC to host communication is also possible for notification of events from the BMC. This requires that the host have interrupts enabled on mailbox data register 15 (or otherwise poll on bit 7 of mailbox status register 1). On receiving such a notification the host should read mailbox data register 15 to determine the event code was set by the BMC (see BMC Event notifications in Commands for detail). After performing the necessary action the host should send a BMC_EVENT_ACK message to the BMC with which bit it has actioned.

Layout

Byte 0: COMMAND
Byte 1: Sequence
Byte 2-12: Arguments
Byte 13: Response code
Byte 14: Host controlled status reg
Byte 15: BMC controlled status reg

Commands

RESET_STATE          1
GET_MBOX_INFO        2
GET_FLASH_INFO       3
CREATE_READ_WINDOW   4
CLOSE_WINDOW         5
CREATE_WRITE_WINDOW  6
MARK_WRITE_DIRTY     7
WRITE_FLUSH          8
BMC_EVENT_ACK        9

Sequence

Unique message sequence number to be allocated by the host at the start of a command/response pair. The BMC must ensure the responses to a particular message contain the same sequence number that was in the request from the host.

Responses

SUCCESS       1
PARAM_ERROR   2
WRITE_ERROR   3
SYSTEM_ERROR  4
TIMEOUT       5

Information

All multibyte messages are LSB first(little endian)
All responses must have a valid return code in byte 13

Only one window can be open at once.

Commands in detail

	Command:
		RESET_STATE
		Data:
			-
		Response:
			-
		Notes:
			This command is designed to inform the BMC that it should put
			host LPC mapping back in a state where the SBE will be able to
			use it. Currently this means pointing back to BMC flash
			pre mailbox protocol. Final behavour is still TBD.


	Command:
		GET_MBOX_INFO
		Arguements:
			Args 0: API version

		Response:
			Args 0: API version
			Args 1-2: read window size as number of blocks
			Args 3-4: write window size as number of block
			Args 5: Block size as power of two.


	Command:
		CLOSE_WINDOW
		Arguments:
			-
		Response:
			-
		Notes:
			Close active window. Renders the LPC mapping unusable.


	Command:
		GET_FLASH_INFO
		Arguments:
			-
		Response:
			Args 0-3: Flash size in bytes
			Args 4-7: Erase granule in bytes


	Command:
		CREATE_READ_WINDOW
		Arguments:
			Args 0-1: Read window offset as number of blocks
		Respons:
			Args 0-1: Read window position as number of blocks
		Notes:
			Offset is the offset within the flash, always specified
			  from zero.
			Position is where flash at the requested offset is mapped
			  on the LPC bus as viewed from the host.


	Command:
		CREATE_WRITE_WINDOW
		ARguments:
			Args 0-1: Write window offset as number of blocks
		Response:
			Args 0-1: Write window position as number of blocks
		Notes:
			Offset is the offset within the flash, always specified
			  from zero.
			Position is where flash at the requested offset is mapped
			  on the LPC bus as viewed from the host.


	Command:
		MARK_WRITE_DIRTY
		Data:
			Data 0-1: Where within window as number of blocks
			Data 2-5: Number of dirty bytes
		Response:
			-
		Notes:
			Where within the window is the index of the first dirty
			block within the window - zero refers to the first block of
			the mapping.
			This command marks bytes as dirty but does not nessesarily
			flush them to flash. It is expected that this command will
			respond quickly without actually performing a write to the
			backing store.


	Command
		WRITE_FLUSH
		Data:
			Data 0-1: Where within window as number of blocks
			Data 2-5: Number of dirty bytes
		Response:
			-
		Notes:
			Where within the window is the index of the first dirty
			block within the window - zero refers to the first block of
			the mapping.
			Number of dirty bytes can be zero, this would result in
			writing all bytes previously marked as dirty.
			This command will block untill all dirty bytes have been
			written to the backing store.


	Command:
		BMC_EVENT_ACK
		Data:
			Bits in the BMC status byte (mailbox data register 15) to ack
		Response:
			*clears the bits in mailbox data register 15*
			-
		Notes:
			The host will use this command to acknowledge BMC events
			supplied in mailbox register 15.


	BMC notifications:
		If the BMC needs to tell the host something then it simply
		writes to Byte 15. The host should have interrupts enabled
		on that register, or otherwise be polling it.
		 -[bit 0] BMC reboot. A BMC reboot informs the host that its
		  windows/dirty bytes/in flight commands will be lost and it
		  should attempt to reopen windows and rewrite any data it had
		  not flushed.
		Futhur details TBD