diff --git a/meta-palmetto/conf/machine/palmetto.conf b/meta-palmetto/conf/machine/palmetto.conf
index 82a9b1c..0efdda0 100644
--- a/meta-palmetto/conf/machine/palmetto.conf
+++ b/meta-palmetto/conf/machine/palmetto.conf
@@ -18,9 +18,14 @@
        obmc-phosphor-example-pydbus \
        "
 
-# UBOOT_MACHINE_${MACHINE} = "${MACHINE}_config
 KMACHINE = "aspeed"
 KERNEL_DEVICETREE = "${KMACHINE}-bmc-opp-${MACHINE}.dtb"
 
 require conf/machine/include/ast2400.inc
 require conf/machine/include/obmc-bsp-common.inc
+
+UBOOT_MACHINE_palmetto = "palmetto_config"
+UBOOT_ENTRYPOINT = "0x40008000"
+UBOOT_LOADADDRESS = "0x40008000"
+
+FLASH_SIZE = "32768"
diff --git a/meta-palmetto/recipes-bsp/u-boot/files/config.patch b/meta-palmetto/recipes-bsp/u-boot/files/config.patch
new file mode 100644
index 0000000..c5216e7
--- /dev/null
+++ b/meta-palmetto/recipes-bsp/u-boot/files/config.patch
@@ -0,0 +1,14 @@
+--- a/include/configs/palmetto.h
++++ b/include/configs/palmetto.h
+@@ -96,11 +96,8 @@
+ #define CONFIG_UPDATE           "tftp 40800000 ast2400.scr; so 40800000'"
+ 
+ #define CONFIG_BOOTDELAY	3		/* autoboot after 3 seconds	*/
+-#define CONFIG_AUTOBOOT_KEYED
+ #define CONFIG_AUTOBOOT_PROMPT		\
+ 	"autoboot in %d seconds (stop with 'Delete' key)...\n", bootdelay
+-#define CONFIG_AUTOBOOT_STOP_STR	"\x1b\x5b\x33\x7e" /* 'Delete', ESC[3~ */
+-#define CONFIG_ZERO_BOOTDELAY_CHECK
+ 
+ #ifdef CONFIG_FLASH_AST2300
+ #define CONFIG_BOOTCOMMAND	"bootm 20080000 20300000"
diff --git a/meta-palmetto/recipes-bsp/u-boot/files/fw_env.config b/meta-palmetto/recipes-bsp/u-boot/files/fw_env.config
new file mode 100644
index 0000000..9cb3ad2
--- /dev/null
+++ b/meta-palmetto/recipes-bsp/u-boot/files/fw_env.config
@@ -0,0 +1,22 @@
+# Configuration file for fw_(printenv/setenv) utility.
+# Up to two entries are valid, in this case the redundant
+# environment sector is assumed present.
+# Notice, that the "Number of sectors" is ignored on NOR and SPI-dataflash.
+# Futhermore, if the Flash sector size is ommitted, this value is assumed to
+# be the same as the Environment size, which is valid for NOR and SPI-dataflash
+
+# NOR example
+# MTD device name	Device offset	Env. size	Flash sector size	Number of sectors
+/dev/mtd1		0x0000		0x20000		0x20000
+#/dev/mtd2		0x0000		0x4000		0x4000
+
+# MTD SPI-dataflash example
+# MTD device name	Device offset	Env. size	Flash sector size	Number of sectors
+#/dev/mtd5		0x4200		0x4200
+#/dev/mtd6		0x4200		0x4200
+
+# NAND example
+#/dev/mtd0		0x4000		0x4000		0x20000			2
+
+# Block device example
+#/dev/mmcblk0		0xc0000		0x20000
diff --git a/meta-palmetto/recipes-bsp/u-boot/files/patch-2013.07/0000-u-boot-aspeed-064.patch b/meta-palmetto/recipes-bsp/u-boot/files/patch-2013.07/0000-u-boot-aspeed-064.patch
new file mode 100644
index 0000000..7d8c805
--- /dev/null
+++ b/meta-palmetto/recipes-bsp/u-boot/files/patch-2013.07/0000-u-boot-aspeed-064.patch
Binary files differ
diff --git a/meta-palmetto/recipes-bsp/u-boot/files/patch-2013.07/0001-u-boot-openbmc.patch b/meta-palmetto/recipes-bsp/u-boot/files/patch-2013.07/0001-u-boot-openbmc.patch
new file mode 100644
index 0000000..834f371
--- /dev/null
+++ b/meta-palmetto/recipes-bsp/u-boot/files/patch-2013.07/0001-u-boot-openbmc.patch
@@ -0,0 +1,1937 @@
+diff --git a/arch/arm/cpu/arm926ejs/aspeed/IO.c b/arch/arm/cpu/arm926ejs/aspeed/IO.c
+index 86e9918..b06fdba 100644
+--- a/arch/arm/cpu/arm926ejs/aspeed/IO.c
++++ b/arch/arm/cpu/arm926ejs/aspeed/IO.c
+@@ -31,7 +31,7 @@ static const char ThisFile[] = "IO.c";
+   #include <post.h>
+   #include <malloc.h>
+   #include <net.h>
+-  #include <COMMINF.H>
++  #include "COMMINF.H"
+ #endif
+ #ifdef SLT_DOS
+   #include <stdlib.h>
+@@ -353,4 +353,3 @@ ULONG ReadSOC_DD(ULONG addr)
+ #endif
+     return 0;
+ }
+-
+diff --git a/arch/arm/cpu/arm926ejs/aspeed/LAN9303.c b/arch/arm/cpu/arm926ejs/aspeed/LAN9303.c
+index 498d4fd..fdabd45 100644
+--- a/arch/arm/cpu/arm926ejs/aspeed/LAN9303.c
++++ b/arch/arm/cpu/arm926ejs/aspeed/LAN9303.c
+@@ -13,9 +13,9 @@ static const char ThisFile[] = "LAN9303.c";
+ 
+ #include "SWFUNC.H"
+ #ifdef SLT_UBOOT
+-  #include <COMMINF.H>
+-  #include <MAC.H>
+-  #include <IO.H>
++  #include "COMMINF.H"
++  #include "MAC.H"
++  #include "IO.H"
+ #endif
+ 
+ #ifdef SLT_DOS
+diff --git a/arch/arm/cpu/arm926ejs/aspeed/MAC.c b/arch/arm/cpu/arm926ejs/aspeed/MAC.c
+index 829da92..b4182f5 100644
+--- a/arch/arm/cpu/arm926ejs/aspeed/MAC.c
++++ b/arch/arm/cpu/arm926ejs/aspeed/MAC.c
+@@ -16,7 +16,7 @@ static const char ThisFile[] = "MAC.c";
+ #ifdef SLT_UBOOT
+   #include <common.h>
+   #include <command.h>
+-  #include <COMMINF.H>
++  #include "COMMINF.H"
+   #include "STDUBOOT.H"
+ #endif
+ #ifdef SLT_DOS
+@@ -2081,5 +2081,3 @@ char TestingLoop (ULONG loop_checknum) {
+ 	
+ 	return(0);
+ } // End char TestingLoop (ULONG loop_checknum)
+-
+-
+diff --git a/arch/arm/cpu/arm926ejs/aspeed/Makefile b/arch/arm/cpu/arm926ejs/aspeed/Makefile
+index 378745e..4c4e239 100644
+--- a/arch/arm/cpu/arm926ejs/aspeed/Makefile
++++ b/arch/arm/cpu/arm926ejs/aspeed/Makefile
+@@ -16,7 +16,7 @@
+ 
+ include $(TOPDIR)/config.mk
+ 
+-LIB	= $(obj)lib$(SOC).a
++LIB	= $(obj)lib$(SOC).o
+ 
+ COBJS	= timer.o
+ COBJS	+= reset.o
+@@ -41,7 +41,7 @@ START	:= $(addprefix $(obj),$(START))
+ all:	$(obj).depend $(LIB)
+ 
+ $(LIB):	$(OBJS)
+-	$(AR) $(ARFLAGS) $@ $(OBJS)
++	$(call cmd_link_o_target, $(OBJS))
+ 
+ #########################################################################
+ 
+diff --git a/arch/arm/cpu/arm926ejs/aspeed/NCSI.c b/arch/arm/cpu/arm926ejs/aspeed/NCSI.c
+index 7de06c3..7e86fb6 100644
+--- a/arch/arm/cpu/arm926ejs/aspeed/NCSI.c
++++ b/arch/arm/cpu/arm926ejs/aspeed/NCSI.c
+@@ -16,9 +16,9 @@ static const char ThisFile[] = "NCSI.c";
+ #ifdef SLT_UBOOT
+   #include <common.h>
+   #include <command.h>
+-  #include <COMMINF.H>
+-  #include <NCSI.H>
+-  #include <IO.H>
++  #include "COMMINF.H"
++  #include "NCSI.H"
++  #include "IO.H"
+ #endif
+ #ifdef SLT_DOS
+   #include <stdio.h>
+diff --git a/arch/arm/cpu/arm926ejs/aspeed/PHY.c b/arch/arm/cpu/arm926ejs/aspeed/PHY.c
+index 6afed9d..db73a70 100644
+--- a/arch/arm/cpu/arm926ejs/aspeed/PHY.c
++++ b/arch/arm/cpu/arm926ejs/aspeed/PHY.c
+@@ -16,7 +16,7 @@ static const char ThisFile[] = "PHY.c";
+ #ifdef SLT_UBOOT
+   #include <common.h>
+   #include <command.h>
+-  #include <COMMINF.H>
++  #include "COMMINF.H"
+   #include "STDUBOOT.H"
+ #endif
+ #ifdef SLT_DOS
+diff --git a/arch/arm/cpu/arm926ejs/aspeed/PLLTESTU.c b/arch/arm/cpu/arm926ejs/aspeed/PLLTESTU.c
+index 95958b0..2414d57 100644
+--- a/arch/arm/cpu/arm926ejs/aspeed/PLLTESTU.c
++++ b/arch/arm/cpu/arm926ejs/aspeed/PLLTESTU.c
+@@ -13,11 +13,11 @@ static const char ThisFile[] = "PLLTEST.c";
+ 
+ #include "SWFUNC.H"
+ 
+-#include <COMMINF.H>
+-#include <STDUBOOT.H>
+-#include <TYPEDEF.H>
+-#include <IO.H>
+-#include <PLLTESTU.H>
++#include "COMMINF.H"
++#include "STDUBOOT.H"
++#include "TYPEDEF.H"
++#include "IO.H"
++#include "PLLTESTU.H"
+ 
+ /*
+  * static
+@@ -407,5 +407,3 @@ int pll_function(int argc, char *argv[])
+         return (ERR_FATAL);
+     }
+ }
+-
+-
+diff --git a/arch/arm/cpu/arm926ejs/aspeed/STDUBOOT.H b/arch/arm/cpu/arm926ejs/aspeed/STDUBOOT.H
+index 7fbf590..4e0adf6 100644
+--- a/arch/arm/cpu/arm926ejs/aspeed/STDUBOOT.H
++++ b/arch/arm/cpu/arm926ejs/aspeed/STDUBOOT.H
+@@ -13,6 +13,5 @@
+ 
+ unsigned long int strtoul(char *string, char **endPtr, int base);
+ int atoi( char s[] );
+-int rand(void);
+ 
+ #endif // End STDUBOOT_H
+diff --git a/arch/arm/cpu/arm926ejs/aspeed/STDUBOOT.c b/arch/arm/cpu/arm926ejs/aspeed/STDUBOOT.c
+index 90e2997..4b1f439 100644
+--- a/arch/arm/cpu/arm926ejs/aspeed/STDUBOOT.c
++++ b/arch/arm/cpu/arm926ejs/aspeed/STDUBOOT.c
+@@ -19,11 +19,11 @@ int isspace ( char c )
+ {
+     if ( ( c == ' ' ) || ( c == 9 ) || ( c == 13 ) )
+         return 1;
+-    
++
+     return 0;
+ }
+ 
+-/* 
++/*
+  * strtoul.c --
+  *
+  *  Source code for the "strtoul" library procedure.
+@@ -111,7 +111,7 @@ strtoul(char *string, char **endPtr, int base)
+      * If no base was provided, pick one from the leading characters
+      * of the string.
+      */
+-    
++
+     if (base == 0)
+     {
+     if (*p == '0') {
+@@ -219,17 +219,6 @@ int atoi( char s[] )
+         ans = ( 10 * ans ) + ( s[i] - '0' );
+ 
+     return ans;
+-} 
+-
+-// -----------------------------------------------------------------------------
+-/* rand:return pseudo-random integer on 0...32767 */
+-int rand(void)
+-{
+-    static unsigned long int next = 1;
+-    
+-    next = next * 1103515245 + 12345; 
+-
+-    return (unsigned int) ( next / 65536 ) % 32768;
+ }
+ 
+ #endif // End SLT_UBOOT
+diff --git a/arch/arm/cpu/arm926ejs/aspeed/STRESS.c b/arch/arm/cpu/arm926ejs/aspeed/STRESS.c
+index dffd64f..e86685e 100644
+--- a/arch/arm/cpu/arm926ejs/aspeed/STRESS.c
++++ b/arch/arm/cpu/arm926ejs/aspeed/STRESS.c
+@@ -12,8 +12,8 @@
+ static const char ThisFile[] = "STRESS.c";
+ 
+ #include "SWFUNC.H"
+-#include <COMMINF.H>
+-#include <IO.H>
++#include "COMMINF.H"
++#include "IO.H"
+ 
+ #define TIMEOUT_DRAM              5000000
+ 
+@@ -142,4 +142,3 @@ int dram_stress_function(int argc, char *argv[])
+      
+      return( ret );
+ }
+-
+diff --git a/arch/arm/cpu/arm926ejs/aspeed/TRAPTEST.c b/arch/arm/cpu/arm926ejs/aspeed/TRAPTEST.c
+index 72936c0..24ec0c5 100644
+--- a/arch/arm/cpu/arm926ejs/aspeed/TRAPTEST.c
++++ b/arch/arm/cpu/arm926ejs/aspeed/TRAPTEST.c
+@@ -13,9 +13,9 @@ static const char ThisFile[] = "PLLTEST.c";
+ 
+ #include "SWFUNC.H"
+ 
+-#include <COMMINF.H>
+-#include <TYPEDEF.H>
+-#include <IO.H>
++#include "COMMINF.H"
++#include "TYPEDEF.H"
++#include "IO.H"
+ 
+ #define ASTCHIP_2400    0
+ #define ASTCHIP_2300    1
+diff --git a/arch/arm/cpu/arm926ejs/aspeed/mactest.c b/arch/arm/cpu/arm926ejs/aspeed/mactest.c
+index 95bd560..62a696d 100644
+--- a/arch/arm/cpu/arm926ejs/aspeed/mactest.c
++++ b/arch/arm/cpu/arm926ejs/aspeed/mactest.c
+@@ -19,9 +19,9 @@ static const char ThisFile[] = "MACTEST.c";
+   #include <post.h>
+   #include <malloc.h>
+   #include <net.h>
+-  #include <COMMINF.H>
+-  #include <STDUBOOT.H>
+-  #include <IO.H>
++  #include "COMMINF.H"
++  #include "STDUBOOT.H"
++  #include "IO.H"
+ #else
+   #include <stdlib.h>
+   #include <string.h>
+@@ -1212,4 +1212,3 @@ Find_Err_IOMargin:;
+     return(Finish_Check(0));
+    
+ }
+-
+diff --git a/arch/arm/cpu/arm926ejs/aspeed/reset.c b/arch/arm/cpu/arm926ejs/aspeed/reset.c
+index e0a57f9..ce8dba1 100644
+--- a/arch/arm/cpu/arm926ejs/aspeed/reset.c
++++ b/arch/arm/cpu/arm926ejs/aspeed/reset.c
+@@ -17,7 +17,7 @@ void reset_cpu(ulong addr)
+ {
+ 	__raw_writel(0x10 , AST_WDT_BASE+0x04);
+ 	__raw_writel(0x4755, AST_WDT_BASE+0x08);
+-	__raw_writel(0x3, AST_WDT_BASE+0x0c);
++	__raw_writel(0x23, AST_WDT_BASE+0x0c); /* reset the full chip */
+ 
+ 	while (1)
+ 	/*nothing*/;
+diff --git a/arch/arm/cpu/arm926ejs/aspeed/timer.c b/arch/arm/cpu/arm926ejs/aspeed/timer.c
+index 4bba5c5..add4c0e 100644
+--- a/arch/arm/cpu/arm926ejs/aspeed/timer.c
++++ b/arch/arm/cpu/arm926ejs/aspeed/timer.c
+@@ -16,12 +16,17 @@
+  */
+ 
+ #include <common.h>
+-#include <arm926ejs.h>
++
++#if CONFIG_ASPEED_TIMER_CLK < CONFIG_SYS_HZ
++#error "CONFIG_ASPEED_TIMER_CLK must be as large as CONFIG_SYS_HZ"
++#endif
+ 
+ #define TIMER_LOAD_VAL 0xffffffff
++#define CLK_PER_HZ (CONFIG_ASPEED_TIMER_CLK / CONFIG_SYS_HZ)
+ 
+ /* macro to read the 32 bit timer */
+-#define READ_TIMER (*(volatile ulong *)(CONFIG_SYS_TIMERBASE+0))
++#define READ_CLK (*(volatile ulong *)(CONFIG_SYS_TIMERBASE + 0))
++#define READ_TIMER (READ_CLK / CLK_PER_HZ)
+ 
+ static ulong timestamp;
+ static ulong lastdec;
+@@ -57,27 +62,25 @@ void set_timer (ulong t)
+ }
+ 
+ /* delay x useconds AND perserve advance timstamp value */
+-void udelay (unsigned long usec)
++void __udelay (unsigned long usec)
+ {
+-	ulong tmo, tmp;
+-
+-	if(usec >= 1000){		/* if "big" number, spread normalization to seconds */
+-		tmo = usec / 1000;	/* start to normalize for usec to ticks per sec */
+-		tmo *= CONFIG_SYS_HZ;		/* find number of "ticks" to wait to achieve target */
+-		tmo /= 1000;		/* finish normalize. */
+-	}else{				/* else small number, don't kill it prior to HZ multiply */
+-		tmo = usec * CONFIG_SYS_HZ;
+-		tmo /= (1000*1000);
+-	}
+-
+-	tmp = get_timer (0);		/* get current timestamp */
+-	if( (tmo + tmp + 1) < tmp )	/* if setting this fordward will roll time stamp */
+-		reset_timer_masked ();	/* reset "advancing" timestamp to 0, set lastdec value */
+-	else
+-		tmo += tmp;		/* else, set advancing stamp wake up time */
+-
+-	while (get_timer_masked () < tmo)/* loop till event */
+-		/*NOP*/;
++  ulong last = READ_CLK;
++  ulong clks;
++  ulong elapsed = 0;
++
++  /* translate usec to clocks */
++  clks = (usec / 1000) * CLK_PER_HZ;
++  clks += (usec % 1000) * CLK_PER_HZ / 1000;
++
++  while (clks > elapsed) {
++    ulong now = READ_CLK;
++    if (now <= last) {
++      elapsed += last - now;
++    } else {
++      elapsed += TIMER_LOAD_VAL - (now - last);
++    }
++    last = now;
++  }
+ }
+ 
+ void reset_timer_masked (void)
+@@ -100,7 +103,7 @@ ulong get_timer_masked (void)
+ 		 * (TLV-now) amount of time after passing though -1
+ 		 * nts = new "advancing time stamp"...it could also roll and cause problems.
+ 		 */
+-		timestamp += lastdec + TIMER_LOAD_VAL - now;
++		timestamp += lastdec + (TIMER_LOAD_VAL / CLK_PER_HZ) - now;
+ 	}
+ 	lastdec = now;
+ 
+@@ -110,25 +113,7 @@ ulong get_timer_masked (void)
+ /* waits specified delay value and resets timestamp */
+ void udelay_masked (unsigned long usec)
+ {
+-	ulong tmo;
+-	ulong endtime;
+-	signed long diff;
+-
+-	if (usec >= 1000) {		/* if "big" number, spread normalization to seconds */
+-		tmo = usec / 1000;	/* start to normalize for usec to ticks per sec */
+-		tmo *= CONFIG_SYS_HZ;		/* find number of "ticks" to wait to achieve target */
+-		tmo /= 1000;		/* finish normalize. */
+-	} else {			/* else small number, don't kill it prior to HZ multiply */
+-		tmo = usec * CONFIG_SYS_HZ;
+-		tmo /= (1000*1000);
+-	}
+-
+-	endtime = get_timer_masked () + tmo;
+-
+-	do {
+-		ulong now = get_timer_masked ();
+-		diff = endtime - now;
+-	} while (diff >= 0);
++  __udelay(usec);
+ }
+ 
+ /*
+@@ -146,8 +131,5 @@ unsigned long long get_ticks(void)
+  */
+ ulong get_tbclk (void)
+ {
+-	ulong tbclk;
+-
+-	tbclk = CONFIG_SYS_HZ;
+-	return tbclk;
++	return CONFIG_SYS_HZ;
+ }
+diff --git a/board/aspeed/ast2400/Makefile b/board/aspeed/ast2400/Makefile
+index 1970ea1..fb77fc9 100644
+--- a/board/aspeed/ast2400/Makefile
++++ b/board/aspeed/ast2400/Makefile
+@@ -11,7 +11,7 @@
+ 
+ include $(TOPDIR)/config.mk
+ 
+-LIB	= $(obj)lib$(BOARD).a
++LIB	= $(obj)lib$(BOARD).o
+ 
+ COBJS   := ast2400.o flash.o flash_spi.o pci.o crc32.o slt.o regtest.o vfun.o vhace.o crt.o videotest.o mactest.o hactest.o mictest.o
+ 
+@@ -28,17 +28,13 @@ OBJS    := $(addprefix $(obj),$(COBJS))
+ SOBJS   := $(addprefix $(obj),$(SOBJS))
+ 
+ $(LIB): $(obj).depend $(OBJS) $(SOBJS)
+-	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
++	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
+ 
+-clean:
+-	rm -f $(SOBJS) $(OBJS)
+-
+-distclean:	clean
+-	rm -f $(LIB) core *.bak $(obj).depend
++#########################################################################
+ 
+ # defines $(obj).depend target
+ include $(SRCTREE)/rules.mk
+ 
+-sinclude .depend
++sinclude $(obj).depend
+ 
+ #########################################################################
+diff --git a/board/aspeed/ast2400/ast2400.c b/board/aspeed/ast2400/ast2400.c
+index 65bccbe..55ed6b7 100644
+--- a/board/aspeed/ast2400/ast2400.c
++++ b/board/aspeed/ast2400/ast2400.c
+@@ -10,6 +10,7 @@
+  */
+ 
+ #include <common.h>
++#include <asm/io.h>
+ #include <command.h>
+ #include <pci.h>
+ 
+@@ -105,8 +106,8 @@ int dram_init (void)
+ {
+     DECLARE_GLOBAL_DATA_PTR;
+ 
+-    gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+-    gd->bd->bi_dram[0].size  = PHYS_SDRAM_1_SIZE;
++    /* dram_init must store complete ramsize in gd->ram_size */
++    gd->ram_size = get_ram_size((void *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE);
+ 
+     return 0;
+ }
+@@ -190,6 +191,22 @@ int ast1070_calibration()
+ 	return 0;
+ }
+ 
++static void watchdog_init()
++{
++#ifdef CONFIG_ASPEED_ENABLE_WATCHDOG
++#define AST_WDT_BASE 0x1e785000
++#define AST_WDT_CLK (1*1000*1000) /* 1M clock source */
++  u32 reload = AST_WDT_CLK * CONFIG_ASPEED_WATCHDOG_TIMEOUT;
++  /* set the reload value */
++  __raw_writel(reload, AST_WDT_BASE + 0x04);
++  /* magic word to reload */
++  __raw_writel(0x4755, AST_WDT_BASE + 0x08);
++  /* start the watchdog with 1M clk src and reset whole chip */
++  __raw_writel(0x33, AST_WDT_BASE + 0x0c);
++  printf("Watchdog: %us\n", CONFIG_ASPEED_WATCHDOG_TIMEOUT);
++#endif
++}
++
+ int misc_init_r(void)
+ {
+     unsigned int reg, reg1, revision, chip_id, lpc_plus;
+@@ -290,6 +307,8 @@ int misc_init_r(void)
+     if (getenv ("eeprom") == NULL) {
+ 	setenv ("eeprom", "y");
+     }
++
++    watchdog_init();
+ }
+ 
+ #ifdef	CONFIG_PCI
+@@ -302,3 +321,15 @@ void pci_init_board(void)
+     aspeed_init_pci(&hose);
+ }
+ #endif
++
++int board_eth_init(bd_t *bis)
++{
++  int ret = -1;
++#if defined(CONFIG_ASPEEDNIC)
++  ret = aspeednic_initialize(bis);
++#else
++  printf("No ETH, ");
++#endif
++
++  return ret;
++}
+diff --git a/board/aspeed/ast2400/config.mk b/board/aspeed/ast2400/config.mk
+index 24ca09b..eddc3bf 100755
+--- a/board/aspeed/ast2400/config.mk
++++ b/board/aspeed/ast2400/config.mk
+@@ -9,10 +9,5 @@
+ # MA 02111-1307 USA
+ #
+ 
+-# ROM version
+-#TEXT_BASE = 0xBFC00000
+-
+-# RAM version
+-TEXT_BASE = 0x40500000
+-#TEXT_BASE = 0x00000000
+-#TEXT_BASE = 0x00400000
++# SPI flash is mapped to 0x00000000 initially
++CONFIG_SYS_TEXT_BASE = 0x00000000
+diff --git a/board/aspeed/ast2400/flash_spi.c b/board/aspeed/ast2400/flash_spi.c
+index ad89254..339e531 100755
+--- a/board/aspeed/ast2400/flash_spi.c
++++ b/board/aspeed/ast2400/flash_spi.c
+@@ -23,7 +23,7 @@
+  */
+ 
+ /* The DEBUG define must be before common to enable debugging */
+-/* #define DEBUG	*/
++/* #define DEBUG */
+ 
+ #include <common.h>
+ #include <asm/processor.h>
+@@ -68,6 +68,7 @@ flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];		/* FLASH chips info */
+ /* Support Flash ID */
+ #define STM25P64		0x172020
+ #define STM25P128		0x182020
++#define N25Q128			0x18ba20
+ #define N25Q256			0x19ba20
+ #define N25Q512			0x20ba20
+ #define S25FL064A		0x160201
+@@ -581,7 +582,7 @@ static ulong flash_get_size (ulong base, int banknum)
+         ulID = ((ulong)ch[0]) | ((ulong)ch[1] << 8) | ((ulong)ch[2] << 16) ;        
+         info->flash_id = ulID;
+         
+-        //printf("SPI Flash ID: %x \n", ulID);
++        printf("SPI Flash ID: %x \n", ulID);
+ 
+         /* init default */        
+         info->iomode = IOMODEx1;
+@@ -617,6 +618,19 @@ static ulong flash_get_size (ulong base, int banknum)
+             ReadClk  = 50;
+             break;
+             
++        case N25Q128:
++	    info->sector_count = 256;
++	    info->size = 0x1000000;        	
++            erase_region_size  = 0x10000;
++            info->readcmd = 0x0b;            
++            info->dualport = 0;
++            info->dummybyte = 1;
++            info->buffersize = 256;            
++            WriteClk = 50;
++            EraseClk = 20;
++            ReadClk  = 50;
++	    break;
++
+         case N25Q256:
+ 	    info->sector_count = 256;
+ 	    info->size = 0x1000000;        	
+@@ -1051,8 +1065,7 @@ AST2300 A0 SPI can't run faster than 50Mhz
+             } /* JDEC */        
+         }
+         				
+-        debug ("erase_region_count = %d erase_region_size = %d\n",
+-		erase_region_count, erase_region_size);
++        debug ("erase_region_size = %d\n", erase_region_size);
+ 
+ 	sector = base;			
+ 	for (j = 0; j < info->sector_count; j++) {
+diff --git a/board/aspeed/ast2400/platform.S b/board/aspeed/ast2400/platform.S
+index 27e8f26..dd94da0 100644
+--- a/board/aspeed/ast2400/platform.S
++++ b/board/aspeed/ast2400/platform.S
+@@ -334,7 +334,11 @@ set_MPLL:
+     str r1, [r0]
+ 
+ /* Debug - UART console message */
+-    ldr r0, =0x1e78400c
++    ldr r0, =0x1e6e2080
++    ldr r1, =0xFFFF0000                          @ enable UART3 and UART4
++    str r1, [r0]
++
++    ldr r0, =CONFIG_ASPEED_COM_LCR
+     mov r1, #0x83
+     str r1, [r0]
+ 
+@@ -342,28 +346,38 @@ set_MPLL:
+     ldr r2, [r0]
+     mov r2, r2, lsr #12
+     tst r2, #0x01
+-    ldr r0, =0x1e784000
++    ldr r0, =CONFIG_ASPEED_COM
++#if CONFIG_BAUDRATE == 115200
+     moveq r1, #0x0D                              @ Baudrate 115200
+     movne r1, #0x01                              @ Baudrate 115200, div13
+-#if defined(CONFIG_DRAM_UART_38400)
++#endif
++#if CONFIG_BAUDRATE == 57600
++    moveq r1, #0x1A                              @ Baudrate 57600
++    movne r1, #0x02                              @ Baudrate 57600, div13
++#endif
++#if CONFIG_BAUDRATE == 38400
+     moveq r1, #0x27                              @ Baudrate 38400
+     movne r1, #0x03                              @ Baudrate 38400 , div13
+ #endif
++#if CONFIG_BAUDRATE == 9600
++    moveq r1, #0x9c                              @ Baudrate 9600
++    movne r1, #0x0C                              @ Baudrate 9600 , div13
++#endif
+     str r1, [r0]
+ 
+-    ldr r0, =0x1e784004
++    ldr r0, =CONFIG_ASPEED_COM_IER
+     mov r1, #0x00
+     str r1, [r0]
+ 
+-    ldr r0, =0x1e78400c
++    ldr r0, =CONFIG_ASPEED_COM_LCR
+     mov r1, #0x03
+     str r1, [r0]
+ 
+-    ldr r0, =0x1e784008
++    ldr r0, =CONFIG_ASPEED_COM_IIR
+     mov r1, #0x07
+     str r1, [r0]
+ 
+-    ldr r0, =0x1e784000
++    ldr r0, =CONFIG_ASPEED_COM
+     mov r1, #0x0D                                @ '\r'
+     str r1, [r0]
+     mov r1, #0x0A                                @ '\n'
+@@ -575,7 +589,7 @@ delay_2:
+  ******************************************************************************/
+ ddr3_init:
+ /* Debug - UART console message */
+-    ldr r0, =0x1e784000
++    ldr r0, =CONFIG_ASPEED_COM
+     mov r1, #0x33                                @ '3'
+     str r1, [r0]
+     mov r1, #0x0D                                @ '\r'
+@@ -764,7 +778,7 @@ delay3_4:
+  ******************************************************************************/
+ ddr2_init:
+ /* Debug - UART console message */
+-    ldr r0, =0x1e784000
++    ldr r0, =CONFIG_ASPEED_COM
+     mov r1, #0x32                                @ '2'
+     str r1, [r0]
+     mov r1, #0x0D                                @ '\r'
+@@ -1416,7 +1430,7 @@ init_sram_start3:
+  *****************************************************************************/
+ CBR0_START:
+ /* Debug - UART console message */
+-    ldr r0, =0x1e784000
++    ldr r0, =CONFIG_ASPEED_COM
+     mov r1, #0x43                                @ 'C'
+     str r1, [r0]
+     mov r1, #0x42                                @ 'B'
+@@ -1454,7 +1468,7 @@ cbr0_next_dqidly:
+     bgt   CBR0_END
+ 
+ /* Debug - UART console message */
+-    ldr   r0, =0x1e784000
++    ldr   r0, =CONFIG_ASPEED_COM
+     and   r1, r8, #0x07
+     add   r1, r1, #0x30                          @ '0-7'
+     str   r1, [r0]
+@@ -1776,7 +1790,7 @@ delay_5:
+  *****************************************************************************/
+ CBR1_START:
+ /* Debug - UART console message */
+-    ldr r0, =0x1e784000
++    ldr r0, =CONFIG_ASPEED_COM
+     mov r1, #0x0D                                @ '\r'
+     str r1, [r0]
+     mov r1, #0x0A                                @ '\n'
+@@ -2057,7 +2071,7 @@ cbr1_set_result_end:
+ 
+ CBR3_START:
+ /* Debug - UART console message */
+-    ldr r0, =0x1e784000
++    ldr r0, =CONFIG_ASPEED_COM
+     mov r1, #0x33                                @ '3'
+     str r1, [r0]
+ /* Debug - UART console message */
+@@ -2276,7 +2290,7 @@ CBR3_END:
+  *****************************************************************************/
+ CBR4_START:
+ /* Debug - UART console message */
+-    ldr r0, =0x1e784000
++    ldr r0, =CONFIG_ASPEED_COM
+     mov r1, #0x34                                @ '4'
+     str r1, [r0]
+ /* Debug - UART console message */
+@@ -2556,7 +2570,7 @@ set_scratch:
+     str r1, [r0]
+ 
+ /* Debug - UART console message */
+-    ldr r0, =0x1e784000
++    ldr r0, =CONFIG_ASPEED_COM
+     mov r1, #0x44                                @ 'D'
+     str r1, [r0]
+     mov r1, #0x6F                                @ 'o'
+@@ -2724,11 +2738,13 @@ ECC_Init_Flag:
+     orr r1, r1, #0x08
+     str r1, [r0]
+ 
++#ifndef CONFIG_ASPEED_ENABLE_JTAG
+     ldr r0, =0x1e6e2004
+     ldr r1, [r0]
+     ldr r2, =0xFFBFFFFF                          @ Enable JTAG Master, solve ARM stucked by JTAG issue
+     and r1, r1, r2
+     str r1, [r0]
++#endif
+ 
+     ldr r0, =0x1e6e2048                          @ Set MAC interface delay timing
+     ldr r1, =0x2255
+diff --git a/board/aspeed/ast2400/u-boot.lds b/board/aspeed/ast2400/u-boot.lds
+deleted file mode 100755
+index ff0fe22..0000000
+--- a/board/aspeed/ast2400/u-boot.lds
++++ /dev/null
+@@ -1,56 +0,0 @@
+-/*
+- * (C) Copyright 2004
+- * Wolfgang Denk, DENX Software Engineering, <wg@denx.de>
+- *
+- * See file CREDITS for list of people who contributed to this
+- * project.
+- *
+- * This program is free software; you can redistribute it and/or
+- * modify it under the terms of the GNU General Public License as
+- * published by the Free Software Foundation; either version 2 of
+- * the License, or (at your option) any later version.
+- *
+- * This program is distributed in the hope that it will be useful,
+- * but WITHOUT ANY WARRANTY; without even the implied warranty of
+- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+- * GNU General Public License for more details.
+- *
+- * You should have received a copy of the GNU General Public License
+- * along with this program; if not, write to the Free Software
+- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+- * MA 02111-1307 USA
+- */
+-
+-OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+-/*OUTPUT_FORMAT("elf32-arm", "elf32-arm", "elf32-arm")*/
+-OUTPUT_ARCH(arm)
+-ENTRY(_start)
+-SECTIONS
+-{
+-	. = 0x00000000;
+-
+-	. = ALIGN(4);
+-	.text	   :
+-	{
+-	  cpu/arm926ejs/start.o	(.text)
+-	  *(.text)
+-	}
+-
+-	. = ALIGN(4);
+-	.rodata : { *(.rodata) }
+-
+-	. = ALIGN(4);
+-	.data : { *(.data) }
+-
+-	. = ALIGN(4);
+-	.got : { *(.got) }
+-
+-	__u_boot_cmd_start = .;
+-	.u_boot_cmd : { *(.u_boot_cmd) }
+-	__u_boot_cmd_end = .;
+-
+-	. = ALIGN(4);
+-	__bss_start = .;
+-	.bss : { *(.bss) }
+-	_end = .;
+-}
+diff --git a/boards.cfg b/boards.cfg
+index 674896b..ce6bff1 100644
+--- a/boards.cfg
++++ b/boards.cfg
+@@ -72,7 +72,8 @@ mini2440                     arm         arm920t     mini2440            friendl
+ VCMA9                        arm         arm920t     vcma9               mpl            s3c24x0
+ smdk2410                     arm         arm920t     -                   samsung        s3c24x0
+ omap1510inn                  arm         arm925t     -                   ti
+-ast2400                      arm         arm926ejs   ast2400             aspeed         aspeed
++wedge                        arm         arm926ejs   ast2400             aspeed         aspeed
++palmetto                     arm         arm926ejs   ast2400             aspeed         aspeed
+ integratorap_cm926ejs        arm         arm926ejs   integrator          armltd         -           integratorap:CM926EJ_S
+ integratorcp_cm926ejs        arm         arm926ejs   integrator          armltd         -           integratorcp:CM924EJ_S
+ aspenite                     arm         arm926ejs   -                   Marvell        armada100
+diff --git a/common/cmd_slt.c b/common/cmd_slt.c
+index 9763692..6296416 100644
+--- a/common/cmd_slt.c
++++ b/common/cmd_slt.c
+@@ -9,6 +9,7 @@
+  *  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+ 
++#include <common.h>
+ #include <command.h>
+ 
+ extern int pll_function(int argc, char *argv[]);
+diff --git a/common/env_common.c b/common/env_common.c
+index 906b41f..f5af537 100644
+--- a/common/env_common.c
++++ b/common/env_common.c
+@@ -203,6 +203,9 @@ void env_relocate(void)
+ #else
+ 		bootstage_error(BOOTSTAGE_ID_NET_CHECKSUM);
+ 		set_default_env("!bad CRC");
++#ifdef CONFIG_ASPEED_WRITE_DEFAULT_ENV
++    saveenv();
++#endif
+ #endif
+ 	} else {
+ 		env_relocate_spec();
+diff --git a/common/image.c b/common/image.c
+index f5ad097..2fc071b 100644
+--- a/common/image.c
++++ b/common/image.c
+@@ -902,6 +902,11 @@ int boot_get_ramdisk(int argc, char * const argv[], bootm_headers_t *images,
+ 			rd_data = image_get_data(rd_hdr);
+ 			rd_len = image_get_data_size(rd_hdr);
+ 			rd_load = image_get_load(rd_hdr);
++#ifdef CONFIG_ASPEED
++			/* Need to copy the initrd into RAM */
++			memmove_wd((void *)rd_load, (void *)rd_data, rd_len, CHUNKSZ);
++			rd_data = rd_load;
++#endif
+ 			break;
+ #if defined(CONFIG_FIT)
+ 		case IMAGE_FORMAT_FIT:
+diff --git a/drivers/net/aspeednic.c b/drivers/net/aspeednic.c
+index 6b1ce05..d75ef67 100644
+--- a/drivers/net/aspeednic.c
++++ b/drivers/net/aspeednic.c
+@@ -16,6 +16,7 @@
+ #include <malloc.h>
+ #include <net.h>
+ #include <pci.h>
++#include <linux/mii.h>
+ 
+ 
+ /*
+@@ -53,7 +54,6 @@
+ #define MAC1_MDC                 (1 << 30)
+ #define MAC1_PHY_LINK            (1 << 0)
+ #define MAC2_MDC_MDIO            (1 << 2)
+-#define MAC1_PHY_LINK            (1 << 0)
+ #define MAC2_PHY_LINK            (1 << 1)
+ #else
+ #define MAC2_MDC_MDIO            (1 << 20)
+@@ -69,6 +69,9 @@ unsigned int aspeednic_iobase[CONFIG_ASPEED_MAC_NUMBER] = {
+   0x1E660000, 0x1E680000};
+ #endif
+ 
++/* PHY address */
++static u8 g_phy_addr = 0;
++
+ #undef DEBUG_SROM
+ #undef DEBUG_SROM2
+ 
+@@ -249,6 +252,7 @@ struct de4x5_desc {
+ #define PHYID_RTL8201EL     0x001cc810
+ #define PHYID_RTL8211         0x001cc910
+ #define PHYID_BCM54612E             0x03625E6A
++#define PHYID_BCM54616S             0x03625D12
+ 
+ //NCSI define & structure
+ //NC-SI Command Packet
+@@ -410,6 +414,12 @@ static void  aspeednic_halt(struct eth_device* dev);
+ static void  set_mac_address (struct eth_device* dev, bd_t* bis);
+ static void  phy_write_register (struct eth_device* dev, u8 PHY_Register, u8 PHY_Address, u16 PHY_Data);
+ static u16   phy_read_register (struct eth_device* dev, u8 PHY_Register, u8 PHY_Address);
++#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
++static int faraday_mdio_read(const char *devname, uint8_t addr, uint8_t reg,
++                             uint16_t *value);
++static int faraday_mdio_write(const char *devname, uint8_t addr, uint8_t reg,
++                              uint16_t value);
++#endif
+ static void  set_mac_control_register(struct eth_device* dev);
+ 
+ #if defined(CONFIG_E500)
+@@ -456,7 +466,7 @@ void NCSI_Struct_Initialize(void)
+ 
+ int aspeednic_initialize(bd_t *bis)
+ {
+-  int               card_number = 0;
++  int               card_number = CONFIG_ASPEED_MAC_CONFIG - 1;
+   unsigned int    iobase, SCURegister;
+   struct eth_device*  dev;
+ 
+@@ -538,7 +548,7 @@ int aspeednic_initialize(bd_t *bis)
+ 
+   dev->iobase = iobase;
+ 
+-  if (CONFIG_MAC1_PHY_SETTING >= 1) {
++  if (CONFIG_ASPEED_MAC_PHY_SETTING >= 1) {
+ //NCSI Struct Initialize
+     NCSI_Struct_Initialize();
+   }
+@@ -556,20 +566,22 @@ int aspeednic_initialize(bd_t *bis)
+   dev->recv   = aspeednic_recv;
+ 
+   /* Ensure we're not sleeping. */
+-  if (CONFIG_MAC1_PHY_SETTING >= 1) {
++  if (CONFIG_ASPEED_MAC_PHY_SETTING >= 1) {
+     udelay(2000000); //2.0 sec
+   }
+   else {
+     udelay(10 * 1000);
+   }
+ 
+-
+   dev->init(dev, bis);
+ 
+   eth_register(dev);
+ 
++#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
++  miiphy_register(dev->name, faraday_mdio_read, faraday_mdio_write);
++#endif
+ 
+-  return card_number;
++  return 1;
+ }
+ 
+ void Calculate_Checksum(unsigned char *buffer_base, int Length)
+@@ -1114,11 +1126,37 @@ void Set_Link (struct eth_device* dev)
+   Retry = 0;
+ }
+ 
++static void aspeednic_probe_phy(struct eth_device *dev)
++{
++  u8 phy_addr;
++  u16 phy_id;
++
++  /* assume it as 0 */
++  g_phy_addr = 0;
++
++  /* Check if the PHY is up to snuff..., max phy addr is 0x1f */
++  for (phy_addr = 0; phy_addr <= 0x1f; phy_addr++) {
++    phy_id = phy_read_register(dev, MII_PHYSID1, phy_addr);
++    /*
++     * When it is unable to found PHY,
++     * the interface usually return 0xffff or 0x0000
++     */
++    if (phy_id != 0xffff && phy_id != 0x0) {
++      g_phy_addr = phy_addr;
++      break;
++    }
++  }
++  printf("%s: PHY at 0x%02x\n", dev->name, phy_addr);
++}
++
+ static int aspeednic_init(struct eth_device* dev, bd_t* bis)
+ {
+   unsigned long i, Package_Found = 0, Channel_Found = 0, Re_Send = 0, Link_Status;
+ 
+   RESET_DE4X5(dev);
++
++  aspeednic_probe_phy(dev);
++
+   set_mac_address (dev, bis);
+   set_mac_control_register (dev);
+ 
+@@ -1149,7 +1187,7 @@ static int aspeednic_init(struct eth_device* dev, bd_t* bis)
+   tx_new = 0;
+   rx_new = 0;
+ 
+-  if (CONFIG_MAC1_PHY_SETTING >= 1) {
++  if (CONFIG_ASPEED_MAC_PHY_SETTING >= 1) {
+ //NCSI Start
+ //DeSelect Package/ Select Package
+     for (i = 0; i < 4; i++) {
+@@ -1313,58 +1351,23 @@ static void aspeednic_halt(struct eth_device* dev)
+ 
+ static void set_mac_address (struct eth_device* dev, bd_t* bis)
+ {
+-  unsigned char  mac_address[6]; // 6 bytes mac address
+-  unsigned char  ethaddress[20]; // string for setenv function
+-  char *s;
+-  int i, env;                // env variable 0: eeprom, 1: environment parameters
+-
+-  s = getenv ("eeprom");
+-  env = (s && (*s == 'y')) ? 0 : 1;
+-
+-  if (env == 0) {
+-    env = 1;
+-    eeprom_init ();
+-    eeprom_read (0xA0, 0, mac_address, 6);
+-
+-    for (i = 0; i < 6; i++) {
+-      if (mac_address[i] != 0xFF) {
+-        env = 0;  //Suppose not all 0xFF is valid
+-      }
+-    }
++  if (!eth_getenv_enetaddr_by_index("eth", 0, dev->enetaddr)) {
++    eth_random_enetaddr(dev->enetaddr);
+   }
+ 
+-  if (env == 0) { // EEPROM
+-    sprintf (ethaddress, "%02X:%02X:%02X:%02X:%02X:%02X", mac_address[0], mac_address[1], mac_address[2], mac_address[3], mac_address[4], mac_address[5]);
+-    setenv ("ethaddr", ethaddress);
+-    OUTL(dev, ((mac_address[2] << 24) | (mac_address[3] << 16) | (mac_address[4] << 8) | mac_address[5]), MAC_LADR_REG);
+-    OUTL(dev, ((mac_address[0] << 8) | mac_address[1]), MAC_MADR_REG);
+-    if (CONFIG_MAC1_PHY_SETTING >= 1) {
+-      for (i = 0; i < 6; i++) {
+-        NCSI_Request.SA[i] = mac_address[i];
+-      }
+-    }
+-  }
+-  else { // Environment Parameters
+-    OUTL(dev, ((bis->bi_enetaddr[2] << 24) | (bis->bi_enetaddr[3] << 16) | (bis->bi_enetaddr[4] << 8) | bis->bi_enetaddr[5]), MAC_LADR_REG);
+-    OUTL(dev, ((bis->bi_enetaddr[0] << 8) | bis->bi_enetaddr[1]), MAC_MADR_REG);
+-    if (CONFIG_MAC1_PHY_SETTING >= 1) {
+-      for (i = 0; i < 6; i++) {
+-        NCSI_Request.SA[i] = bis->bi_enetaddr[i];
+-      }
+-    }
++  OUTL(dev, ((dev->enetaddr[2] << 24) | (dev->enetaddr[3] << 16)
++             | (dev->enetaddr[4] << 8) | dev->enetaddr[5]), MAC_LADR_REG);
++  OUTL(dev, ((dev->enetaddr[0] << 8) | dev->enetaddr[1]), MAC_MADR_REG);
++  if (CONFIG_ASPEED_MAC_PHY_SETTING >= 1) {
++    memcpy(NCSI_Request.SA, dev->enetaddr, 6);
+   }
+-
+ }
+ 
+-
+ static u16 phy_read_register (struct eth_device* dev, u8 PHY_Register, u8 PHY_Address)
+ {
+   u32 Data, Status = 0, Loop_Count = 0, PHY_Ready = 1;
+   u16 Return_Data;
+ 
+-#ifdef  REALTEK_PHY_SUPPORT
+-  PHY_Address = 0x01;
+-#endif
+ //20us * 100 = 2ms > (1 / 2.5Mhz) * 0x34
+   OUTL(dev, (PHY_Register << 21) + (PHY_Address << 16) + MIIRD + MDC_CYCTHR, PHYCR_REG);
+   do {
+@@ -1378,7 +1381,6 @@ static u16 phy_read_register (struct eth_device* dev, u8 PHY_Register, u8 PHY_Ad
+   } while (Status == MIIRD);
+ 
+   if (PHY_Ready == 0) {
+-    printf ("PHY NOT REDAY ");
+     return 0;
+   }
+   Data = INL (dev, PHYDATA_REG);
+@@ -1392,9 +1394,6 @@ static void phy_write_register (struct eth_device* dev, u8 PHY_Register, u8 PHY_
+ {
+   u32 Status = 0, Loop_Count = 0, PHY_Ready = 1;
+ 
+-#ifdef  REALTEK_PHY_SUPPORT
+-  PHY_Address = 0x01;
+-#endif
+ //20us * 100 = 2ms > (1 / 2.5Mhz) * 0x34
+   OUTL(dev, PHY_Data, PHYDATA_REG);
+   OUTL(dev, (PHY_Register << 21) + (PHY_Address << 16) + MIIWR + MDC_CYCTHR, PHYCR_REG);
+@@ -1407,31 +1406,66 @@ static void phy_write_register (struct eth_device* dev, u8 PHY_Register, u8 PHY_
+       break;
+     }
+   } while (Status == MIIWR);
+-  if (PHY_Ready == 0) {
+-    printf ("PHY NOT REDAY ");
++}
++
++#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
++
++static int faraday_mdio_read(
++  const char *devname, uint8_t addr, uint8_t reg, uint16_t *value)
++{
++  int ret = 0;
++  struct eth_device *dev;
++
++  dev = eth_get_dev_by_name(devname);
++  if (dev == NULL) {
++    printf("%s: no such device\n", devname);
++    ret = -1;
++  } else {
++    *value = phy_read_register(dev, reg, addr);
++  }
++
++  return ret;
++}
++
++static int faraday_mdio_write(
++  const char *devname, uint8_t addr, uint8_t reg, uint16_t value)
++{
++  int ret = 0;
++  struct eth_device *dev;
++
++  dev = eth_get_dev_by_name(devname);
++  if (dev == NULL) {
++    printf("%s: no such device\n", devname);
++    ret = -1;
++  } else {
++    phy_write_register(dev, reg, addr, value);
+   }
++
++  return ret;
+ }
+ 
++#endif    /* #if defined(CONFIG_MII) || defined(CONFIG_CMD_MII) */
++
+ static void set_mac_control_register (struct eth_device* dev)
+ {
+   unsigned long MAC_CR_Register = 0;
+-  unsigned long   Loop_Count = 0, PHY_Ready = 1, Chip_ID;
++  unsigned int   Loop_Count = 0, PHY_Ready = 1, Chip_ID;
+   u16    PHY_Status, PHY_Speed, PHY_Duplex, Resolved_Status = 0, Advertise, Link_Partner;
+ 
+-  if (CONFIG_MAC1_PHY_SETTING >= 1) {
++  if (CONFIG_ASPEED_MAC_PHY_SETTING >= 1) {
+     MAC_CR_Register = SPEED_100M_MODE_bit | RX_BROADPKT_bit | FULLDUP_bit | RXMAC_EN_bit | RXDMA_EN_bit | TXMAC_EN_bit | TXDMA_EN_bit | CRC_APD_bit;
+   }
+   else {
+     MAC_CR_Register = SPEED_100M_MODE_bit | FULLDUP_bit | RXMAC_EN_bit | RXDMA_EN_bit | TXMAC_EN_bit | TXDMA_EN_bit | CRC_APD_bit;
+   }
+ 
+-  if (CONFIG_MAC1_PHY_SETTING != 2) {
+-    Chip_ID = ((phy_read_register (dev, 0x02, 0)) << 16);
+-    Chip_ID |= (phy_read_register (dev, 0x03, 0) & 0xffff);
++  if (CONFIG_ASPEED_MAC_PHY_SETTING != 2) {
++    Chip_ID = ((phy_read_register (dev, 0x02, g_phy_addr)) << 16);
++    Chip_ID |= (phy_read_register (dev, 0x03, g_phy_addr) & 0xffff);
+     if (((Chip_ID & PHYID_VENDOR_MASK) == PHYID_VENDOR_BROADCOM) ||
+         ((Chip_ID & PHYID_VENDOR_MODEL_MASK) == PHYID_RTL8201EL)) {
+-      Advertise = phy_read_register (dev, 0x04, 0);
+-      Link_Partner = phy_read_register (dev, 0x05, 0);
++      Advertise = phy_read_register (dev, 0x04, g_phy_addr);
++      Link_Partner = phy_read_register (dev, 0x05, g_phy_addr);
+       Advertise = (Advertise & PHY_SPEED_DUPLEX_MASK);
+       Link_Partner = (Link_Partner & PHY_SPEED_DUPLEX_MASK);
+       if ((Advertise & Link_Partner) & PHY_100M_DUPLEX) {
+@@ -1456,7 +1490,8 @@ static void set_mac_control_register (struct eth_device* dev)
+ //Max waiting time = (20 + 2)ms * 250(PHY_LOOP) = 5.5s
+       do {
+         udelay (20000);
+-        Resolved_Status = (phy_read_register (dev, 0x11, 0) & RESOLVED_BIT);
++        Resolved_Status = (phy_read_register (dev, 0x11, g_phy_addr)
++                           & RESOLVED_BIT);
+         Loop_Count++;
+         if (Loop_Count >= PHY_LOOP) {
+           PHY_Ready = 0;
+@@ -1466,7 +1501,7 @@ static void set_mac_control_register (struct eth_device* dev)
+       } while (Resolved_Status != RESOLVED_BIT);
+ 
+       if (PHY_Ready == 1) {
+-        PHY_Status = phy_read_register (dev, 0x11, 0);
++        PHY_Status = phy_read_register (dev, 0x11, g_phy_addr);
+         PHY_Speed = (PHY_Status & PHY_SPEED_MASK) >> 14;
+         PHY_Duplex = (PHY_Status & PHY_DUPLEX_MASK) >> 13;
+ 
+@@ -1485,40 +1520,54 @@ static void set_mac_control_register (struct eth_device* dev)
+       }
+ //LED Control
+ //              if (Chip_ID == 0x1C) {
+-//                  PHY_Status = phy_read_register (dev, 0x18, 0);
+-//                phy_write_register (dev, 0x18, 0, (PHY_Status | 0x09));
++//                  PHY_Status = phy_read_register (dev, 0x18, g_phy_addr);
++//                phy_write_register (dev, 0x18, g_phy_addr, (PHY_Status | 0x09));
+ //              }
+ //LED Control D[0], D[6]
+ //              if (Chip_ID == 0x141) {
+-//                  PHY_Status = phy_read_register (dev, 0x18, 0);
+-//                phy_write_register (dev, 0x18, 0, ((PHY_Status & ~(0x41)) | 0x01));
++//                  PHY_Status = phy_read_register (dev, 0x18, g_phy_addr);
++//                phy_write_register (dev, 0x18, g_phy_addr, ((PHY_Status & ~(0x41)) | 0x01));
+ //              }
+     }
+-    else if (Chip_ID == PHYID_BCM54612E )  {
+-      phy_write_register ( dev, 0x1C, 1, 0x8C00 ); // Disable GTXCLK Clock Delay Enable
+-      phy_write_register ( dev, 0x18, 1, 0xF0E7 ); // Disable RGMII RXD to RXC Skew
+-
+-      Advertise = phy_read_register (dev, 0x04, 1);
+-      Link_Partner = phy_read_register (dev, 0x05, 1);
+-      Advertise = (Advertise & PHY_SPEED_DUPLEX_MASK);
+-      Link_Partner = (Link_Partner & PHY_SPEED_DUPLEX_MASK);
+-      if ((Advertise & Link_Partner) & PHY_100M_DUPLEX) {
+-        MAC_CR_Register |= SPEED_100M_MODE_bit;
+-        MAC_CR_Register |= FULLDUP_bit;
++    else if (Chip_ID == PHYID_BCM54612E || Chip_ID == PHYID_BCM54616S) {
++      // Disable GTXCLK Clock Delay Enable
++      phy_write_register( dev, 0x1C, g_phy_addr, 0x8C00);
++      // Disable RGMII RXD to RXC Skew
++      phy_write_register( dev, 0x18, g_phy_addr, 0xF0E7);
++      // First Switch shadow register selector
++      phy_write_register(dev, 0x1C, g_phy_addr, 0x2000);
++      PHY_Status = phy_read_register(dev, 0x1C, g_phy_addr);
++      PHY_Duplex = (PHY_Status & 0x0080);
++      switch (PHY_Status & 0x0018) {
++      case 0x0000:
++        PHY_Speed = SPEED_1000M;
++        break;
++      case 0x0008:
++        PHY_Speed = SPEED_100M;
++        break;
++      case 0x0010:
++        PHY_Speed = SPEED_10M;
++        break;
++      default:
++        PHY_Speed = SPEED_100M;
++        break;
+       }
+-      else if ((Advertise & Link_Partner) & PHY_100M_HALF) {
+-        MAC_CR_Register |= SPEED_100M_MODE_bit;
+-        MAC_CR_Register &= ~FULLDUP_bit;
++      if (PHY_Speed == SPEED_1000M) {
++        MAC_CR_Register |= GMAC_MODE_bit;
++      } else {
++        MAC_CR_Register &= ~GMAC_MODE_bit;
++        if (PHY_Speed == SPEED_100M) {
++          MAC_CR_Register |= SPEED_100M_MODE_bit;
++        } else {
++          MAC_CR_Register &= ~SPEED_100M_MODE_bit;
++        }
+       }
+-      else if ((Advertise & Link_Partner) & PHY_10M_DUPLEX) {
+-        MAC_CR_Register &= ~SPEED_100M_MODE_bit;
++      if (PHY_Duplex) {
+         MAC_CR_Register |= FULLDUP_bit;
+-      }
+-      else if ((Advertise & Link_Partner) & PHY_10M_HALF) {
+-        MAC_CR_Register &= ~SPEED_100M_MODE_bit;
++      } else {
+         MAC_CR_Register &= ~FULLDUP_bit;
+       }
+-    }else {
++    } else {
+       printf("Unknow Chip_ID %x\n",Chip_ID);
+     }
+   }
+diff --git a/include/configs/wedge.h b/include/configs/wedge.h
+new file mode 100644
+index 0000000..6bb7639
+--- /dev/null
++++ b/include/configs/wedge.h
+@@ -0,0 +1,350 @@
++/*
++ * Copyright 2004-present Facebook. All Rights Reserved.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
++ * MA 02111-1307 USA
++ */
++
++#ifndef __CONFIG_H
++#define __CONFIG_H
++
++/* Uncommit the following line to enable JTAG in u-boot */
++//#define CONFIG_ASPEED_ENABLE_JTAG
++
++/*
++ * High Level Configuration Options
++ * (easy to change)
++ */
++//#define CONFIG_INIT_CRITICAL			/* define for U-BOOT 1.1.1 */
++#undef  CONFIG_INIT_CRITICAL			/* undef for  U-BOOT 1.1.4 */
++//#define CONFIG_FPGA_ASPEED	1
++#define CONFIG_ARM926EJS	1		/* This is an arm926ejs CPU */
++#define	CONFIG_ASPEED		1
++#define CONFIG_AST2400		1
++//#define CONFIG_AST1070		1
++//#define CONFIG_SYS_FLASH_CFI			/* CONFIG_FLASH_CFI, CONFIG_FLASH_SPI is exclusive*/
++#define CONFIG_FLASH_SPI
++//#define CONFIG_2SPIFLASH			/* Boot SPI: CS2, 2nd SPI: CS0 */
++#undef CONFIG_2SPIFLASH
++#undef CONFIG_ASPEED_SLT
++#define CONFIG_FLASH_AST2300
++//#define CONFIG_FLASH_AST2300_DMA
++//#define CONFIG_FLASH_SPIx2_Dummy
++//#define CONFIG_FLASH_SPIx4_Dummy
++#define CONFIG_CRT_DISPLAY	1		/* undef if not support CRT */
++
++//#define CONFIG_USE_IRQ				/* we don't need IRQ/FIQ stuff */
++#define CONFIG_MISC_INIT_R
++
++/*
++ * DRAM Config
++ *
++ * 1. DRAM Size              //
++ *    CONFIG_DRAM_512MBIT    // 512M bit
++ *    CONFIG_DRAM_1GBIT      // 1G   bit (default)
++ *    CONFIG_DRAM_2GBIT      // 2G   bit
++ *    CONFIG_DRAM_4GBIT      // 4G   bit
++ * 2. DRAM Speed             //
++ *    CONFIG_DRAM_336        // 336MHz (DDR-667)
++ *    CONFIG_DRAM_408        // 408MHz (DDR-800) (default)
++ * 3. VGA Mode
++ *    CONFIG_CRT_DISPLAY     // define to disable VGA function
++ * 4. ECC Function enable
++ *    CONFIG_DRAM_ECC        // define to enable ECC function
++ * 5. UART Debug Message
++ *    CONFIG_DRAM_UART_OUT   // enable output message at UART5
++ *    CONFIG_DRAM_UART_38400 // set the UART baud rate to 38400, default is 115200
++ */
++
++//1. DRAM Size
++//#define    CONFIG_DRAM_512MBIT
++#define    CONFIG_DRAM_1GBIT
++//#define    CONFIG_DRAM_2GBIT
++//#define    CONFIG_DRAM_4GBIT
++//2. DRAM Speed
++//#define    CONFIG_DRAM_336
++#define    CONFIG_DRAM_408
++//3. VGA Mode
++//#define    CONFIG_CRT_DISPLAY
++//4. ECC Function enable
++//#define    CONFIG_DRAM_ECC
++//5. UART Debug Message
++#define    CONFIG_DRAM_UART_OUT
++//#define    CONFIG_DRAM_UART_38400
++
++
++
++/*
++ * Environment Config
++ */
++#define CONFIG_CMDLINE_TAG	 1		/* enable passing of ATAGs	*/
++#define CONFIG_SETUP_MEMORY_TAGS 1
++#define CONFIG_INITRD_TAG	 1
++#define	CONFIG_BOOTARGS 	"debug console=ttyS2,9600n8 root=/dev/ram rw"
++#define CONFIG_UPDATE           "tftp 40800000 ast2400.scr; so 40800000'"
++
++#define CONFIG_BOOTDELAY	3		/* autoboot after 3 seconds	*/
++#define CONFIG_AUTOBOOT_KEYED
++#define CONFIG_AUTOBOOT_PROMPT		\
++	"autoboot in %d seconds (stop with 'Delete' key)...\n", bootdelay
++#define CONFIG_AUTOBOOT_STOP_STR	"\x1b\x5b\x33\x7e" /* 'Delete', ESC[3~ */
++#define CONFIG_ZERO_BOOTDELAY_CHECK
++
++#ifdef CONFIG_FLASH_AST2300
++#define CONFIG_BOOTCOMMAND	"bootm 20080000 20300000"
++#else
++#ifdef	CONFIG_SYS_FLASH_CFI
++#define CONFIG_BOOTCOMMAND	"bootm 10080000 10300000"
++#else
++#define CONFIG_BOOTCOMMAND	"bootm 14080000 14300000"
++#endif
++#endif
++#define CONFIG_BOOTFILE		"all.bin"
++#define CONFIG_ENV_OVERWRITE
++
++/*
++ * Command line configuration.
++ */
++#include <config_cmd_default.h>
++
++#define CONFIG_CMD_DFL
++#define CONFIG_CMD_ENV
++#define CONFIG_CMD_FLASH
++#define CONFIG_CMD_MII
++#define CONFIG_CMD_NET
++#define CONFIG_CMD_PING
++#define CONFIG_CMD_I2C
++#define CONFIG_CMD_EEPROM
++#define CONFIG_CMD_NETTEST
++#define CONFIG_CMD_SLT
++
++/*
++ * CPU Setting
++ */
++#define CPU_CLOCK_RATE		18000000	/* 16.5 MHz clock for the ARM core */
++
++/*
++ * Size of malloc() pool
++ */
++#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 768*1024)
++#define CONFIG_SYS_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
++
++/*
++ * Stack sizes,  The stack sizes are set up in start.S using the settings below
++ */
++#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
++#define CONFIG_STACKSIZE_IRQ	(4*1024)	/* IRQ stack */
++#define CONFIG_STACKSIZE_FIQ	(4*1024)	/* FIQ stack */
++
++/*
++ * Memory Configuration
++ */
++#define CONFIG_NR_DRAM_BANKS	1	   	/* we have 1 bank of DRAM */
++#define PHYS_SDRAM_1		  0x40000000 	/* SDRAM Bank #1 */
++#define PHYS_SDRAM_1_SIZE	0x10000000 	/* 256 MB */
++
++#define CONFIG_SYS_SDRAM_BASE	0x40000000
++
++/*
++ * FLASH Configuration
++ */
++#ifdef CONFIG_SYS_FLASH_CFI				/* NOR Flash */
++
++#ifdef CONFIG_FLASH_AST2300
++#define PHYS_FLASH_1			0x20000000 	/* Flash Bank #1 */
++#else
++#define PHYS_FLASH_1			0x10000000 	/* Flash Bank #1 */
++#endif
++
++#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1
++#define CONFIG_FLASH_BANKS_LIST 	{ PHYS_FLASH_1 }
++
++#define CONFIG_SYS_MAX_FLASH_BANKS 	1
++#define CONFIG_SYS_MAX_FLASH_SECT	(256)		/* max number of sectors on one chip */
++
++#define CONFIG_ENV_IS_IN_FLASH	1
++#define CONFIG_ENV_OFFSET					0x60000 	/* environment starts here  */
++#define CONFIG_ENV_SIZE					0x20000 	/* Total Size of Environment Sector */
++
++#define CONFIG_SYS_FLASH_CFI_AMD_RESET
++#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
++
++#else						/* SPI Flash */
++
++#ifdef CONFIG_FLASH_AST2300
++#define PHYS_FLASH_1		0x20000000 	/* Flash Bank #1 */
++#else
++#define PHYS_FLASH_1		0x14000000 	/* Flash Bank #1 */
++#define PHYS_FLASH_2		0x14800000 	/* Flash Bank #2 */
++#define PHYS_FLASH_2_BASE	0x10000000
++#endif
++
++#ifdef CONFIG_2SPIFLASH
++#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_2_BASE
++#define CONFIG_FLASH_BANKS_LIST 	{ PHYS_FLASH_1, PHYS_FLASH_2 }
++#define CONFIG_SYS_MAX_FLASH_BANKS 	2
++#define CONFIG_SYS_MAX_FLASH_SECT	(1024)		/* max number of sectors on one chip */
++
++#define CONFIG_ENV_IS_IN_FLASH		1
++#define CONFIG_ENV_OFFSET		0x7F0000 	/* environment starts here  */
++#define CONFIG_ENV_SIZE			0x010000 	/* Total Size of Environment Sector */
++#else
++#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1
++#define CONFIG_FLASH_BANKS_LIST 	{ PHYS_FLASH_1 }
++#define CONFIG_SYS_MAX_FLASH_BANKS 	1
++#define CONFIG_SYS_MAX_FLASH_SECT	(1024)		/* max number of sectors on one chip */
++
++#define CONFIG_ENV_IS_IN_FLASH		1
++#define CONFIG_ENV_OFFSET		0x60000 	/* environment starts here  */
++#define CONFIG_ENV_SIZE			0x20000 	/* Total Size of Environment Sector */
++#define CONFIG_ASPEED_WRITE_DEFAULT_ENV
++#endif
++
++#endif
++
++#define __LITTLE_ENDIAN                 1
++
++#define CONFIG_MONITOR_BASE		TEXT_BASE
++#define CONFIG_MONITOR_LEN		(192 << 10)
++
++/* timeout values are in ticks */
++#define CONFIG_SYS_FLASH_ERASE_TOUT	(20*CONFIG_SYS_HZ) 	/* Timeout for Flash Erase */
++#define CONFIG_SYS_FLASH_WRITE_TOUT	(20*CONFIG_SYS_HZ) 	/* Timeout for Flash Write */
++
++/*
++ * Miscellaneous configurable options
++ */
++#define CONFIG_SYS_LONGHELP				/* undef to save memory		*/
++
++#define CONFIG_SYS_PROMPT		"boot# " 	/* Monitor Command Prompt	*/
++#define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
++#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
++#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
++#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
++
++#define CONFIG_SYS_MEMTEST_START	0x40000000	/* memtest works on	*/
++#define CONFIG_SYS_MEMTEST_END		0x44FFFFFF	/* 256 MB in DRAM	*/
++
++#define CONFIG_SYS_LOAD_ADDR		0x43000000	/* default load address */
++
++#define CONFIG_SYS_TIMERBASE		0x1E782000	/* use timer 1 */
++#define CONFIG_SYS_HZ			      1000
++#define CONFIG_ASPEED_TIMER_CLK (1*1000*1000) /* use external clk (1M) */
++
++/*
++ * Serial Configuration
++ */
++#define CONFIG_SYS_NS16550
++#define CONFIG_SYS_NS16550_SERIAL
++#define CONFIG_SYS_NS16550_MEM32
++#define CONFIG_SYS_NS16550_REG_SIZE	-4
++#define CONFIG_SYS_NS16550_CLK		24000000
++#define CONFIG_SYS_NS16550_COM1		0x1e783000
++#define CONFIG_SYS_NS16550_COM2		0x1e784000
++#define CONFIG_SYS_NS16550_COM3		0x1e78e000
++#define	CONFIG_SYS_LOADS_BAUD_CHANGE
++#define CONFIG_CONS_INDEX		2
++#define CONFIG_BAUDRATE			9600
++#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
++#define CONFIG_ASPEED_COM 0x1e78e000 // COM3
++#define CONFIG_ASPEED_COM_IER (CONFIG_ASPEED_COM + 0x4)
++#define CONFIG_ASPEED_COM_IIR (CONFIG_ASPEED_COM + 0x8)
++#define CONFIG_ASPEED_COM_LCR (CONFIG_ASPEED_COM + 0xc)
++
++/*
++ * USB device configuration
++ */
++/*
++#define CONFIG_USB_DEVICE		1
++#define CONFIG_USB_TTY			1
++
++#define CONFIG_USBD_VENDORID		0x1234
++#define CONFIG_USBD_PRODUCTID		0x5678
++#define CONFIG_USBD_MANUFACTURER	"Siemens"
++#define CONFIG_USBD_PRODUCT_NAME	"SX1"
++*/
++
++/*
++ * I2C configuration
++ */
++#define CONFIG_HARD_I2C
++#define CONFIG_SYS_I2C_SPEED		100000
++#define CONFIG_SYS_I2C_SLAVE		1
++#define CONFIG_DRIVER_ASPEED_I2C
++
++/*
++* EEPROM configuration
++*/
++#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 	2
++#define CONFIG_SYS_I2C_EEPROM_ADDR 	0xa0
++
++#define __BYTE_ORDER __LITTLE_ENDIAN
++#define __LITTLE_ENDIAN_BITFIELD
++
++/*
++ * NIC configuration
++ */
++#define CONFIG_ASPEEDNIC
++#define CONFIG_NET_MULTI
++#define CONFIG_MAC1_PHY_LINK_INTERRUPT
++#define CONFIG_MAC2_ENABLE
++#define CONFIG_MAC2_PHY_LINK_INTERRUPT
++/*
++*-------------------------------------------------------------------------------
++* NOTICE: MAC1 and MAC2 now have their own seperate PHY configuration.
++* We use 2 bits for each MAC in the scratch register(D[15:11] in 0x1E6E2040) to
++* inform kernel driver.
++* The meanings of the 2 bits are:
++* 00(0): Dedicated PHY
++* 01(1): ASPEED's EVA + INTEL's NC-SI PHY chip EVA
++* 10(2): ASPEED's MAC is connected to NC-SI PHY chip directly
++* 11: Reserved
++*
++* We use CONFIG_MAC1_PHY_SETTING and CONFIG_MAC2_PHY_SETTING in U-Boot
++* 0: Dedicated PHY
++* 1: ASPEED's EVA + INTEL's NC-SI PHY chip EVA
++* 2: ASPEED's MAC is connected to NC-SI PHY chip directly
++* 3: Reserved
++*-------------------------------------------------------------------------------
++*/
++#define CONFIG_MAC1_PHY_SETTING		0
++#define CONFIG_MAC2_PHY_SETTING		0
++#define CONFIG_ASPEED_MAC_NUMBER  2
++#define CONFIG_ASPEED_MAC_CONFIG  2 // config MAC2
++#define _PHY_SETTING_CONCAT(mac) CONFIG_MAC##mac##_PHY_SETTING
++#define _GET_MAC_PHY_SETTING(mac) _PHY_SETTING_CONCAT(mac)
++#define CONFIG_ASPEED_MAC_PHY_SETTING \
++  _GET_MAC_PHY_SETTING(CONFIG_ASPEED_MAC_CONFIG)
++#define CONFIG_MAC_INTERFACE_CLOCK_DELAY	0x2255
++#define CONFIG_RANDOM_MACADDR
++//#define CONFIG_GATEWAYIP 192.168.0.1
++//#define CONFIG_NETMASK   255.255.255.0
++//#define CONFIG_IPADDR    192.168.0.45
++//#define CONFIG_SERVERIP  192.168.0.81
++
++/*
++ * SLT
++ */
++/*
++#define CONFIG_SLT
++#define CFG_CMD_SLT		(CFG_CMD_VIDEOTEST | CFG_CMD_MACTEST | CFG_CMD_HACTEST | CFG_CMD_MICTEST)
++*/
++
++#define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
++
++#define CONFIG_ASPEED_ENABLE_WATCHDOG
++#define CONFIG_ASPEED_WATCHDOG_TIMEOUT (5*60) // 5m
++
++#endif	/* __CONFIG_H */
+diff --git a/include/configs/palmetto.h b/include/configs/palmetto.h
+new file mode 100644
+index 0000000..6bb7639
+--- /dev/null
++++ b/include/configs/palmetto.h
+@@ -0,0 +1,350 @@
++/*
++ * Copyright 2004-present Facebook. All Rights Reserved.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
++ * MA 02111-1307 USA
++ */
++
++#ifndef __CONFIG_H
++#define __CONFIG_H
++
++/* Uncommit the following line to enable JTAG in u-boot */
++//#define CONFIG_ASPEED_ENABLE_JTAG
++
++/*
++ * High Level Configuration Options
++ * (easy to change)
++ */
++//#define CONFIG_INIT_CRITICAL			/* define for U-BOOT 1.1.1 */
++#undef  CONFIG_INIT_CRITICAL			/* undef for  U-BOOT 1.1.4 */
++//#define CONFIG_FPGA_ASPEED	1
++#define CONFIG_ARM926EJS	1		/* This is an arm926ejs CPU */
++#define	CONFIG_ASPEED		1
++#define CONFIG_AST2400		1
++//#define CONFIG_AST1070		1
++//#define CONFIG_SYS_FLASH_CFI			/* CONFIG_FLASH_CFI, CONFIG_FLASH_SPI is exclusive*/
++#define CONFIG_FLASH_SPI
++//#define CONFIG_2SPIFLASH			/* Boot SPI: CS2, 2nd SPI: CS0 */
++#undef CONFIG_2SPIFLASH
++#undef CONFIG_ASPEED_SLT
++#define CONFIG_FLASH_AST2300
++//#define CONFIG_FLASH_AST2300_DMA
++//#define CONFIG_FLASH_SPIx2_Dummy
++//#define CONFIG_FLASH_SPIx4_Dummy
++#define CONFIG_CRT_DISPLAY	1		/* undef if not support CRT */
++
++//#define CONFIG_USE_IRQ				/* we don't need IRQ/FIQ stuff */
++#define CONFIG_MISC_INIT_R
++
++/*
++ * DRAM Config
++ *
++ * 1. DRAM Size              //
++ *    CONFIG_DRAM_512MBIT    // 512M bit
++ *    CONFIG_DRAM_1GBIT      // 1G   bit (default)
++ *    CONFIG_DRAM_2GBIT      // 2G   bit
++ *    CONFIG_DRAM_4GBIT      // 4G   bit
++ * 2. DRAM Speed             //
++ *    CONFIG_DRAM_336        // 336MHz (DDR-667)
++ *    CONFIG_DRAM_408        // 408MHz (DDR-800) (default)
++ * 3. VGA Mode
++ *    CONFIG_CRT_DISPLAY     // define to disable VGA function
++ * 4. ECC Function enable
++ *    CONFIG_DRAM_ECC        // define to enable ECC function
++ * 5. UART Debug Message
++ *    CONFIG_DRAM_UART_OUT   // enable output message at UART5
++ *    CONFIG_DRAM_UART_38400 // set the UART baud rate to 38400, default is 115200
++ */
++
++//1. DRAM Size
++//#define    CONFIG_DRAM_512MBIT
++#define    CONFIG_DRAM_1GBIT
++//#define    CONFIG_DRAM_2GBIT
++//#define    CONFIG_DRAM_4GBIT
++//2. DRAM Speed
++//#define    CONFIG_DRAM_336
++#define    CONFIG_DRAM_408
++//3. VGA Mode
++//#define    CONFIG_CRT_DISPLAY
++//4. ECC Function enable
++//#define    CONFIG_DRAM_ECC
++//5. UART Debug Message
++#define    CONFIG_DRAM_UART_OUT
++//#define    CONFIG_DRAM_UART_38400
++
++
++
++/*
++ * Environment Config
++ */
++#define CONFIG_CMDLINE_TAG	 1		/* enable passing of ATAGs	*/
++#define CONFIG_SETUP_MEMORY_TAGS 1
++#define CONFIG_INITRD_TAG	 1
++#define	CONFIG_BOOTARGS 	"debug console=ttyS0,57600n8 root=/dev/ram rw"
++#define CONFIG_UPDATE           "tftp 40800000 ast2400.scr; so 40800000'"
++
++#define CONFIG_BOOTDELAY	3		/* autoboot after 3 seconds	*/
++#define CONFIG_AUTOBOOT_KEYED
++#define CONFIG_AUTOBOOT_PROMPT		\
++	"autoboot in %d seconds (stop with 'Delete' key)...\n", bootdelay
++#define CONFIG_AUTOBOOT_STOP_STR	"\x1b\x5b\x33\x7e" /* 'Delete', ESC[3~ */
++#define CONFIG_ZERO_BOOTDELAY_CHECK
++
++#ifdef CONFIG_FLASH_AST2300
++#define CONFIG_BOOTCOMMAND	"bootm 20080000 20300000"
++#else
++#ifdef	CONFIG_SYS_FLASH_CFI
++#define CONFIG_BOOTCOMMAND	"bootm 10080000 10300000"
++#else
++#define CONFIG_BOOTCOMMAND	"bootm 14080000 14300000"
++#endif
++#endif
++#define CONFIG_BOOTFILE		"all.bin"
++#define CONFIG_ENV_OVERWRITE
++
++/*
++ * Command line configuration.
++ */
++#include <config_cmd_default.h>
++
++#define CONFIG_CMD_DFL
++#define CONFIG_CMD_ENV
++#define CONFIG_CMD_FLASH
++#define CONFIG_CMD_MII
++#define CONFIG_CMD_NET
++#define CONFIG_CMD_PING
++#define CONFIG_CMD_I2C
++#define CONFIG_CMD_EEPROM
++#define CONFIG_CMD_NETTEST
++#define CONFIG_CMD_SLT
++
++/*
++ * CPU Setting
++ */
++#define CPU_CLOCK_RATE		18000000	/* 16.5 MHz clock for the ARM core */
++
++/*
++ * Size of malloc() pool
++ */
++#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 768*1024)
++#define CONFIG_SYS_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
++
++/*
++ * Stack sizes,  The stack sizes are set up in start.S using the settings below
++ */
++#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
++#define CONFIG_STACKSIZE_IRQ	(4*1024)	/* IRQ stack */
++#define CONFIG_STACKSIZE_FIQ	(4*1024)	/* FIQ stack */
++
++/*
++ * Memory Configuration
++ */
++#define CONFIG_NR_DRAM_BANKS	1	   	/* we have 1 bank of DRAM */
++#define PHYS_SDRAM_1		  0x40000000 	/* SDRAM Bank #1 */
++#define PHYS_SDRAM_1_SIZE	0x10000000 	/* 256 MB */
++
++#define CONFIG_SYS_SDRAM_BASE	0x40000000
++
++/*
++ * FLASH Configuration
++ */
++#ifdef CONFIG_SYS_FLASH_CFI				/* NOR Flash */
++
++#ifdef CONFIG_FLASH_AST2300
++#define PHYS_FLASH_1			0x20000000 	/* Flash Bank #1 */
++#else
++#define PHYS_FLASH_1			0x10000000 	/* Flash Bank #1 */
++#endif
++
++#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1
++#define CONFIG_FLASH_BANKS_LIST 	{ PHYS_FLASH_1 }
++
++#define CONFIG_SYS_MAX_FLASH_BANKS 	1
++#define CONFIG_SYS_MAX_FLASH_SECT	(256)		/* max number of sectors on one chip */
++
++#define CONFIG_ENV_IS_IN_FLASH	1
++#define CONFIG_ENV_OFFSET					0x60000 	/* environment starts here  */
++#define CONFIG_ENV_SIZE					0x20000 	/* Total Size of Environment Sector */
++
++#define CONFIG_SYS_FLASH_CFI_AMD_RESET
++#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
++
++#else						/* SPI Flash */
++
++#ifdef CONFIG_FLASH_AST2300
++#define PHYS_FLASH_1		0x20000000 	/* Flash Bank #1 */
++#else
++#define PHYS_FLASH_1		0x14000000 	/* Flash Bank #1 */
++#define PHYS_FLASH_2		0x14800000 	/* Flash Bank #2 */
++#define PHYS_FLASH_2_BASE	0x10000000
++#endif
++
++#ifdef CONFIG_2SPIFLASH
++#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_2_BASE
++#define CONFIG_FLASH_BANKS_LIST 	{ PHYS_FLASH_1, PHYS_FLASH_2 }
++#define CONFIG_SYS_MAX_FLASH_BANKS 	2
++#define CONFIG_SYS_MAX_FLASH_SECT	(1024)		/* max number of sectors on one chip */
++
++#define CONFIG_ENV_IS_IN_FLASH		1
++#define CONFIG_ENV_OFFSET		0x7F0000 	/* environment starts here  */
++#define CONFIG_ENV_SIZE			0x010000 	/* Total Size of Environment Sector */
++#else
++#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1
++#define CONFIG_FLASH_BANKS_LIST 	{ PHYS_FLASH_1 }
++#define CONFIG_SYS_MAX_FLASH_BANKS 	1
++#define CONFIG_SYS_MAX_FLASH_SECT	(1024)		/* max number of sectors on one chip */
++
++#define CONFIG_ENV_IS_IN_FLASH		1
++#define CONFIG_ENV_OFFSET		0x60000 	/* environment starts here  */
++#define CONFIG_ENV_SIZE			0x20000 	/* Total Size of Environment Sector */
++#define CONFIG_ASPEED_WRITE_DEFAULT_ENV
++#endif
++
++#endif
++
++#define __LITTLE_ENDIAN                 1
++
++#define CONFIG_MONITOR_BASE		TEXT_BASE
++#define CONFIG_MONITOR_LEN		(192 << 10)
++
++/* timeout values are in ticks */
++#define CONFIG_SYS_FLASH_ERASE_TOUT	(20*CONFIG_SYS_HZ) 	/* Timeout for Flash Erase */
++#define CONFIG_SYS_FLASH_WRITE_TOUT	(20*CONFIG_SYS_HZ) 	/* Timeout for Flash Write */
++
++/*
++ * Miscellaneous configurable options
++ */
++#define CONFIG_SYS_LONGHELP				/* undef to save memory		*/
++
++#define CONFIG_SYS_PROMPT		"boot# " 	/* Monitor Command Prompt	*/
++#define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
++#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
++#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
++#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
++
++#define CONFIG_SYS_MEMTEST_START	0x40000000	/* memtest works on	*/
++#define CONFIG_SYS_MEMTEST_END		0x44FFFFFF	/* 256 MB in DRAM	*/
++
++#define CONFIG_SYS_LOAD_ADDR		0x43000000	/* default load address */
++
++#define CONFIG_SYS_TIMERBASE		0x1E782000	/* use timer 1 */
++#define CONFIG_SYS_HZ			      1000
++#define CONFIG_ASPEED_TIMER_CLK (1*1000*1000) /* use external clk (1M) */
++
++/*
++ * Serial Configuration
++ */
++#define CONFIG_SYS_NS16550
++#define CONFIG_SYS_NS16550_SERIAL
++#define CONFIG_SYS_NS16550_MEM32
++#define CONFIG_SYS_NS16550_REG_SIZE	-4
++#define CONFIG_SYS_NS16550_CLK		24000000
++#define CONFIG_SYS_NS16550_COM1		0x1e783000
++#define CONFIG_SYS_NS16550_COM2		0x1e784000
++#define CONFIG_SYS_NS16550_COM3		0x1e78e000
++#define	CONFIG_SYS_LOADS_BAUD_CHANGE
++#define CONFIG_CONS_INDEX		3
++#define CONFIG_BAUDRATE			57600
++#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
++#define CONFIG_ASPEED_COM 0x1e784000 // UART5
++#define CONFIG_ASPEED_COM_IER (CONFIG_ASPEED_COM + 0x4)
++#define CONFIG_ASPEED_COM_IIR (CONFIG_ASPEED_COM + 0x8)
++#define CONFIG_ASPEED_COM_LCR (CONFIG_ASPEED_COM + 0xc)
++
++/*
++ * USB device configuration
++ */
++/*
++#define CONFIG_USB_DEVICE		1
++#define CONFIG_USB_TTY			1
++
++#define CONFIG_USBD_VENDORID		0x1234
++#define CONFIG_USBD_PRODUCTID		0x5678
++#define CONFIG_USBD_MANUFACTURER	"Siemens"
++#define CONFIG_USBD_PRODUCT_NAME	"SX1"
++*/
++
++/*
++ * I2C configuration
++ */
++#define CONFIG_HARD_I2C
++#define CONFIG_SYS_I2C_SPEED		100000
++#define CONFIG_SYS_I2C_SLAVE		1
++#define CONFIG_DRIVER_ASPEED_I2C
++
++/*
++* EEPROM configuration
++*/
++#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 	2
++#define CONFIG_SYS_I2C_EEPROM_ADDR 	0xa0
++
++#define __BYTE_ORDER __LITTLE_ENDIAN
++#define __LITTLE_ENDIAN_BITFIELD
++
++/*
++ * NIC configuration
++ */
++#define CONFIG_ASPEEDNIC
++#define CONFIG_NET_MULTI
++#define CONFIG_MAC1_PHY_LINK_INTERRUPT
++#define CONFIG_MAC2_ENABLE
++#define CONFIG_MAC2_PHY_LINK_INTERRUPT
++/*
++*-------------------------------------------------------------------------------
++* NOTICE: MAC1 and MAC2 now have their own seperate PHY configuration.
++* We use 2 bits for each MAC in the scratch register(D[15:11] in 0x1E6E2040) to
++* inform kernel driver.
++* The meanings of the 2 bits are:
++* 00(0): Dedicated PHY
++* 01(1): ASPEED's EVA + INTEL's NC-SI PHY chip EVA
++* 10(2): ASPEED's MAC is connected to NC-SI PHY chip directly
++* 11: Reserved
++*
++* We use CONFIG_MAC1_PHY_SETTING and CONFIG_MAC2_PHY_SETTING in U-Boot
++* 0: Dedicated PHY
++* 1: ASPEED's EVA + INTEL's NC-SI PHY chip EVA
++* 2: ASPEED's MAC is connected to NC-SI PHY chip directly
++* 3: Reserved
++*-------------------------------------------------------------------------------
++*/
++#define CONFIG_MAC1_PHY_SETTING		2
++#define CONFIG_MAC2_PHY_SETTING		0
++#define CONFIG_ASPEED_MAC_NUMBER  1
++#define CONFIG_ASPEED_MAC_CONFIG  1 // config MAC1
++#define _PHY_SETTING_CONCAT(mac) CONFIG_MAC##mac##_PHY_SETTING
++#define _GET_MAC_PHY_SETTING(mac) _PHY_SETTING_CONCAT(mac)
++#define CONFIG_ASPEED_MAC_PHY_SETTING \
++  _GET_MAC_PHY_SETTING(CONFIG_ASPEED_MAC_CONFIG)
++#define CONFIG_MAC_INTERFACE_CLOCK_DELAY	0x2255
++#define CONFIG_RANDOM_MACADDR
++//#define CONFIG_GATEWAYIP 192.168.0.1
++//#define CONFIG_NETMASK   255.255.255.0
++//#define CONFIG_IPADDR    192.168.0.45
++//#define CONFIG_SERVERIP  192.168.0.81
++
++/*
++ * SLT
++ */
++/*
++#define CONFIG_SLT
++#define CFG_CMD_SLT		(CFG_CMD_VIDEOTEST | CFG_CMD_MACTEST | CFG_CMD_HACTEST | CFG_CMD_MICTEST)
++*/
++
++#define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
++
++#define CONFIG_ASPEED_ENABLE_WATCHDOG
++#define CONFIG_ASPEED_WATCHDOG_TIMEOUT (5*60) // 5m
++
++#endif	/* __CONFIG_H */
diff --git a/meta-palmetto/recipes-bsp/u-boot/u-boot_2013.07%.bbappend b/meta-palmetto/recipes-bsp/u-boot/u-boot_2013.07%.bbappend
new file mode 100644
index 0000000..6d4a18f
--- /dev/null
+++ b/meta-palmetto/recipes-bsp/u-boot/u-boot_2013.07%.bbappend
@@ -0,0 +1,13 @@
+FILESEXTRAPATHS_prepend := "${THISDIR}/files:"
+
+#SRC_URI += "file://fw_env.config
+SRC_URI += "file://patch-2013.07/0000-u-boot-aspeed-064.patch \
+           file://patch-2013.07/0001-u-boot-openbmc.patch \
+           file://config.patch \
+           "
+
+# Do not install u-boot in rootfs
+#do_install[postfuncs] += "remove_uboot_from_rootfs"
+#remove_uboot_from_rootfs() {
+#    rm -rf ${D}/boot/u-boot*
+#}