DHCPv6 Enable/ Disable Test Cases
Changes:
DHCPv6 enable/ disable test cases
Tested:
Ran and Tested on BMC Environment.
Change-Id: I85f034d3ba7fc424de4220f45deabc2d3dcd9a80
Signed-off-by: Sweta Potthuri <spotthur@in.ibm.com>
diff --git a/redfish/managers/test_bmc_ipv6.robot b/redfish/managers/test_bmc_ipv6.robot
index 127b230..10b45bf 100644
--- a/redfish/managers/test_bmc_ipv6.robot
+++ b/redfish/managers/test_bmc_ipv6.robot
@@ -214,17 +214,6 @@
Check BMC Gets SLAAC Address
-Enable And Verify DHCPv6 Property On Eth1 When DHCPv6 Property Enabled On Eth0
- [Documentation] Verify DHCPv6 on eth1 when DHCPv6 property is enabled on eth0.
- [Tags] Enable_And_Verify_DHCPv6_Property_On_Eth1_When_DHCPv6_Property_Enabled_On_Eth0
- [Setup] Get The Initial DHCPv6 Settings
- [Teardown] Run Keywords Set And Verify DHCPv6 Property ${dhcpv6_channel_1} ${1}
- ... AND Set And Verify DHCPv6 Property ${dhcpv6_channel_2} ${2}
-
- Set And Verify DHCPv6 Property Enabled ${1}
- Set And Verify DHCPv6 Property Enabled ${2}
-
-
Verify Enable And Disable SLAAC On Both Interfaces
[Documentation] Verify enable and disable SLAAC on both the interfaces.
[Tags] Verify_Enable_And_Disable_SLAAC_On_Both_Interfaces
@@ -240,6 +229,22 @@
${False} ${False}
+Configure And Validate DHCPv6 Settings On Both Network Interfaces
+ [Documentation] Configure and validate the DHCPv6 enable/disable settings
+ ... on both network interfaces.
+ [Tags] Configure_And_Validate_DHCPv6_Settings_On_Both_Network_Interfaces
+ [Setup] Get The Initial DHCPv6 Settings
+ [Template] Set And Verify DHCPv6 Property On Both Interfaces
+ [Teardown] Run Keywords Set And Verify DHCPv6 Property ${dhcpv6_channel_1} ${1} AND
+ ... Set And Verify DHCPv6 Property ${dhcpv6_channel_2} ${2}
+
+ # DHCPv6_eth0 DHCPv6_eth1
+ Enabled Enabled
+ Enabled Disabled
+ Disabled Enabled
+ Disabled Disabled
+
+
Verify Autoconfig Is Present On Ethernet Interface
[Documentation] Verify autoconfig is present on ethernet interface.
[Tags] Verify_Autoconfig_Is_Present_On_Ethernet_Interface
@@ -881,13 +886,27 @@
# dhcpv6_operating_mode Enable/ Disable DHCPv6.
# channel_number Channel number 1 or 2.
- ${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']}
+ ${ethernet_interface}= Set Variable ${active_channel_config['${channel_number}']['name']}
${resp}= Redfish.Get ${REDFISH_NW_ETH_IFACE}${ethernet_interface}
${dhcpv6_verify}= Get From Dictionary ${resp.dict} DHCPv6
Should Be Equal '${dhcpv6_verify['OperatingMode']}' '${dhcpv6_operating_mode}'
+ Sleep 30s
+
+ @{ipv6_addressorigin_list} ${ipv6_dhcpv6_addr}=
+ ... Get Address Origin List And IPv4 or IPv6 Address IPv6Addresses ${channel_number}
+
+ IF "${dhcpv6_operating_mode}" == "Enabled"
+ @{ipv6_addressorigin_list} ${ipv6_dhcpv6_addr}=
+ ... Get Address Origin List And Address For Type DHCPv6 ${channel_number}
+ Should Not Be Empty ${ipv6_dhcpv6_addr} msg=DHCPv6 must be present.
+ ELSE
+ Should Not Contain ${ipv6_addressorigin_list} DHCPv6
+ END
+
+
Get IPv6 Static Default Gateway
[Documentation] Get IPv6 static default gateway.
@@ -1300,3 +1319,18 @@
Verify All The Addresses Are Intact ${2}
... ${eth1_initial_ipv4_addressorigin_list} ${eth1_initial_ipv4_addr_list}
+
+Set And Verify DHCPv6 Property On Both Interfaces
+ [Documentation] Set and verify DHCPv6 property on both interfaces.
+ [Arguments] ${dhcpv6_value_1} ${dhcpv6_value_2}
+
+ # Description of the argument(s):
+ # dhcpv6_value_1 DHCPv6 value for channel 1.
+ # dhcpv6_value_2 DHCPv6 value for channel 2.
+
+ Set And Verify DHCPv6 Property ${dhcpv6_value_1} ${1}
+ Set And Verify DHCPv6 Property ${dhcpv6_value_2} ${2}
+
+ Verify All The Addresses Are Intact ${1}
+ Verify All The Addresses Are Intact ${2}
+ ... ${eth1_initial_ipv4_addressorigin_list} ${eth1_initial_ipv4_addr_list}