Switch From Static to DHCP
Changes:
Added test case to switch from static to DHCP
Tested: Tested bmc_network_conf.robot and multiple_interfaces_dhcp.robot
Change-Id: I0cb5629317b9bb26f01a8a6b8740500dd9a7ee47
Signed-off-by: Sweta Potthuri <spotthur@in.ibm.com>
diff --git a/redfish/managers/test_bmc_network_conf.robot b/redfish/managers/test_bmc_network_conf.robot
index c9b61c4..3acd08e 100644
--- a/redfish/managers/test_bmc_network_conf.robot
+++ b/redfish/managers/test_bmc_network_conf.robot
@@ -898,28 +898,3 @@
Sleep ${NETWORK_TIMEOUT}s
Wait For Host To Ping ${OPENBMC_HOST} ${NETWORK_TIMEOUT}
-
-
-Get IPv4 DHCP Enabled Status
- [Documentation] Return IPv4 DHCP enabled status from redfish URI.
-
- ${active_channel_config}= Get Active Channel Config
- ${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']}
- ${resp}= Redfish.Get Attribute ${REDFISH_NW_ETH_IFACE}${ethernet_interface} DHCPv4
- ${status}= Set Variable ${resp['DHCPEnabled']}
- Return From Keyword ${status}
-
-
-Get DHCP IP Info
- [Documentation] Return DHCP IP address, gateway and subnetmask from redfish URI.
-
- ${active_channel_config}= Get Active Channel Config
- ${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']}
- ${resp_list}= Redfish.Get Attribute ${REDFISH_NW_ETH_IFACE}${ethernet_interface} IPv4Addresses
- FOR ${resp} IN @{resp_list}
- Continue For Loop If '${resp['AddressOrigin']}' != 'DHCP'
- ${ip_addr}= Set Variable ${resp['Address']}
- ${gateway}= Set Variable ${resp['Gateway']}
- ${subnetmask}= Set Variable ${resp['SubnetMask']}
- Return From Keyword ${ip_addr} ${gateway} ${subnetmask}
- END
diff --git a/redfish/managers/test_multiple_interfaces_dhcp.robot b/redfish/managers/test_multiple_interfaces_dhcp.robot
index 8a850ec..2ac1ca7 100644
--- a/redfish/managers/test_multiple_interfaces_dhcp.robot
+++ b/redfish/managers/test_multiple_interfaces_dhcp.robot
@@ -1,5 +1,6 @@
*** Settings ***
Documentation Test BMC DHCP multiple network interface functionalities.
+ ... Run on setup eth0 in static and eth1 in DHCP.
Resource ../../lib/resource.robot
Resource ../../lib/common_utils.robot
@@ -43,6 +44,8 @@
[Teardown] Set DHCPEnabled To Enable Or Disable True eth1
Set DHCPEnabled To Enable Or Disable False eth1
+ ${DHCPEnabled}= Get IPv4 DHCP Enabled Status
+ Should Be Equal ${DHCPEnabled} ${False}
Wait For Host To Ping ${OPENBMC_HOST} ${NETWORK_TIMEOUT}
Enable DHCP On Eth1 And Verify System Is Accessible By Eth0
@@ -52,6 +55,8 @@
[Setup] Set DHCPEnabled To Enable Or Disable False eth1
Set DHCPEnabled To Enable Or Disable True eth1
+ ${DHCPEnabled}= Get IPv4 DHCP Enabled Status
+ Should Be Equal ${DHCPEnabled} ${True}
Wait For Host To Ping ${OPENBMC_HOST} ${NETWORK_TIMEOUT}
Set Network Property via Redfish And Verify
@@ -78,7 +83,7 @@
# Getting the eth0 details before enabling DHCP.
${ip_data_before}= Get BMC IP Info
- # Enable DHCP.
+ # Enable DHCP on eth1.
Set DHCPEnabled To Enable Or Disable True eth1
# Check the value of DHCPEnabled on eth0 is not impacted.
@@ -91,16 +96,31 @@
# Before and after IP details must match.
Should Be Equal ${ip_data_before} ${ip_data_after}
+Switch Between DHCP And Static
+ [Documentation] Switch between DHCP and static.
+ [Tags] Switch_Between_DHCP_And_Static
+ [Teardown] Set DHCPEnabled To Enable Or Disable True eth1
+
+ # Fetch the IP details before.
+ ${ip_addr_before} ${gateway_before} ${subnetmask_before} Get DHCP IP Info
+
+ # Switch Between Static and DHCP.
+ FOR ${i} IN RANGE ${10}
+ Set DHCPEnabled To Enable Or Disable False eth1
+ Set DHCPEnabled To Enable Or Disable True eth1
+ END
+ Sleep 5s
+
+ # Fetch the IP details after.
+ ${ip_addr_after} ${gateway_after} ${subnetmask_after} Get DHCP IP Info
+
+ # DHCP Details must be the same before and after.
+ Should Be Equal ${ip_addr_before} ${ip_addr_after}
+ Should Be Equal ${gateway_before} ${gateway_after}
+ Should Be Equal ${subnetmask_before} ${subnetmask_after}
+
*** Keywords ***
-Get IPv4 DHCP Enabled Status
- [Documentation] Return IPv4 DHCP enabled status from redfish URI.
-
- ${active_channel_config}= Get Active Channel Config
- ${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']}
- ${resp}= Redfish.Get Attribute ${REDFISH_NW_ETH_IFACE}${ethernet_interface} DHCPv4
- Return From Keyword ${resp['DHCPEnabled']}
-
Set DHCPEnabled To Enable Or Disable
[Documentation] Enable or Disable DHCP on the interface.
[Arguments] ${dhcp_enabled}=${False} ${interface}=${ethernet_interface}
@@ -183,7 +203,6 @@
[Documentation] Do suite setup task.
Ping Host ${OPENBMC_HOST}
- Ping Host ${OPENBMC_HOST_1}
Redfish.Login
# Get the configuration of eth1
@@ -203,4 +222,3 @@
... AND Set Suite Variable ${eth0_gateway} ${network_configuration['Gateway']}
... AND Exit For Loop
END
-