Verify DHCPv6 on two interfaces
Changes:
- Added the test case
Verify DHCPv6 Can Be Enabled On Both Interfaces
Tested:
Ran and Tested on BMC Environment
Change-Id: I1eb8d3f41649f28668f00b19c49299dfa29bb61c
Signed-off-by: Sweta Potthuri <spotthur@in.ibm.com>
diff --git a/redfish/managers/test_bmc_ipv6.robot b/redfish/managers/test_bmc_ipv6.robot
index d1a5d47..3d6ade6 100644
--- a/redfish/managers/test_bmc_ipv6.robot
+++ b/redfish/managers/test_bmc_ipv6.robot
@@ -124,25 +124,23 @@
[Documentation] Enable DHCPv6 property on BMC and verify.
[Tags] Enable_DHCPv6_Property_On_BMC_And_Verify
- Set DHCPv6 Property Enabled
- Verify DHCPv6 Property Enabled
+ Set And Verify DHCPv6 Property Enabled
Disable DHCPv6 Property On BMC And Verify
[Documentation] Disable DHCPv6 property on BMC and verify.
[Tags] Disable_DHCPv6_Property_On_BMC_And_Verify
- Set DHCPv6 Property Disabled
- Verify DHCPv6 Property Disabled
+ Set And Verify DHCPv6 Property Disabled
Verify Persistency Of DHCPv6 On Reboot
[Documentation] Verify persistency of DHCPv6 property on reboot.
[Tags] Verify_Persistency_Of_DHCPv6_On_Reboot
- Set DHCPv6 Property Enabled
- Redfish OBMC Reboot (off) stack_mode=skip
- Verify DHCPv6 Property Enabled
+ Set And Verify DHCPv6 Property Enabled
+ Redfish OBMC Reboot (off) stack_mode=skip
+ Verify DHCPv6 Property Enabled
Configure Invalid Static IPv6 And Verify
@@ -206,6 +204,18 @@
Check BMC Gets SLAACv6 Address
+Enable And Verify DHCPv6 Property On Eth1 When DHCPv6 Property Enabled On Eth0
+ [Documentation] Verify DHCPv6 on eth1 when DHCPv6 property is enabled on eth0.
+ [Tags] Enable_And_Verify_DHCPv6_Property_On_Eth1_When_DHCPv6_Property_Enabled_On_Eth0
+ [Setup] Run Keywords Get The Initial DHCPv6 Setting ${1} dhcpv6_channel_1
+ ... AND Get The Initial DHCPv6 Setting ${2} dhcpv6_channel_2
+ [Teardown] Run Keywords Set And Verify DHCPv6 Property ${dhcpv6_channel_1} ${1}
+ ... AND Set And Verify DHCPv6 Property ${dhcpv6_channel_2} ${2}
+
+ Set And Verify DHCPv6 Property Enabled ${1}
+ Set And Verify DHCPv6 Property Enabled ${2}
+
+
*** Keywords ***
Suite Setup Execution
@@ -592,16 +602,27 @@
Fail msg=SLAACv6 not set properly.
END
-
-Set DHCPv6 Property
- [Documentation] Set DHCPv6 attribute and verify.
- [Arguments] ${dhcpv6_operating_mode}=${Disabled}
+Set And Verify DHCPv6 Property
+ [Documentation] Set DHCPv6 property and verify.
+ [Arguments] ${dhcpv6_operating_mode}=${Disabled} ${channel_number}=${CHANNEL_NUMBER}
# Description of argument(s):
# dhcpv6_operating_mode Enabled if user wants to enable DHCPv6('Enabled' or 'Disabled').
+ # channel_number Channel number 1 or 2.
+
+ Set DHCPv6 Property ${dhcpv6_operating_mode} ${channel_number}
+ Verify DHCPv6 Property ${dhcpv6_operating_mode} ${channel_number}
+
+
+Set DHCPv6 Property
+ [Documentation] Set DHCPv6 attribute is enables or disabled.
+ [Arguments] ${dhcpv6_operating_mode}=${Disabled} ${channel_number}=${CHANNEL_NUMBER}
+
+ # Description of argument(s):
+ # dhcpv6_operating_mode Enabled if user wants to enable DHCPv6('Enabled' or 'Disabled').
+ # channel_number Channel number 1 or 2.
${data}= Set Variable If '${dhcpv6_operating_mode}' == 'Disabled' ${DISABLE_DHCPv6} ${ENABLE_DHCPv6}
- ${active_channel_config}= Get Active Channel Config
${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']}
Redfish.Patch ${REDFISH_NW_ETH_IFACE}${ethernet_interface}
@@ -610,10 +631,13 @@
Verify DHCPv6 Property
[Documentation] Verify DHCPv6 settings is enabled or disabled.
- [Arguments] ${dhcpv6_operating_mode}
+ [Arguments] ${dhcpv6_operating_mode} ${channel_number}=${CHANNEL_NUMBER}
# Description of Argument(s):
# dhcpv6_operating_mode Enable/ Disable DHCPv6.
+ # channel_number Channel number 1 or 2.
+
+ ${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']}
${resp}= Redfish.Get ${REDFISH_NW_ETH_IFACE}${ethernet_interface}
${dhcpv6_verify}= Get From Dictionary ${resp.dict} DHCPv6
@@ -827,6 +851,21 @@
Should Contain ${ipv6_addressorigin_list} SLAAC
Should Not Be Empty ${ipv6_slaac_addr} msg=SLAACv6 address is not present.
+
+Get The Initial DHCPv6 Setting
+ [Documentation] Get the initial DHCPv6 setting and store in a variable.
+ [Arguments] ${channel_number} ${initial_dhcpv6_before}
+
+ # Description of the argument(s):
+ # channel_number Channel number 1 or 2.
+ # initial_dhcpv6_before Variable to store initial DHCPv6 setting.
+
+ ${ethernet_interface}= Set Variable ${active_channel_config['${channel_number}']['name']}
+ ${resp}= Redfish.Get ${REDFISH_NW_ETH_IFACE}${ethernet_interface}
+ ${initial_dhcpv6_iface}= Get From Dictionary ${resp.dict} DHCPv6
+ Set Test Variable ${${initial_dhcpv6_before}} ${initial_dhcpv6_iface['OperatingMode']}
+
+
Get Address Origin List And Address For Type
[Documentation] Get address origin list and address for type.
[Arguments] ${ipv6_address_type}
@@ -847,5 +886,3 @@
END
END
RETURN @{ipv6_addressorigin_list} ${ipv6_type_addr}
-
-