SLAAC Reboot Test Cases
Changes:
SLAAC reboot test cases.
Tested:
Ran and Tested on BMC Environment.
Change-Id: I4f92dd137040cce009117beeffb47c127a2596d8
Signed-off-by: Sweta Potthuri <spotthur@in.ibm.com>
diff --git a/redfish/managers/test_bmc_ipv6.robot b/redfish/managers/test_bmc_ipv6.robot
index 1cdc11e..3c951f4 100644
--- a/redfish/managers/test_bmc_ipv6.robot
+++ b/redfish/managers/test_bmc_ipv6.robot
@@ -198,6 +198,24 @@
... ${eth1_initial_ipv4_addressorigin_list} ${eth1_initial_ipv4_addr_list}
+Verify Persistency Of SLAAC On BMC Reboot On Eth0
+ [Documentation] Verify persistency of SLAAC property on reboot on eth0.
+ [Tags] Verify_Persistency_Of_SLAAC_On_BMC_Reboot_On_Eth0
+
+ Set SLAAC Configuration State And Verify ${True} [${HTTP_OK}] ${1} ${False}
+ Redfish OBMC Reboot (off) stack_mode=skip
+ Verify SLAAC Property ${True}
+
+
+Verify Persistency Of SLAAC On BMC Reboot On Eth1
+ [Documentation] Verify persistency of SLAAC property on reboot on eth1.
+ [Tags] Verify_Persistency_Of_SLAAC_On_BMC_Reboot_On_Eth1
+
+ Set SLAAC Configuration State And Verify ${True} [${HTTP_OK}] ${2} ${False}
+ Redfish OBMC Reboot (off) stack_mode=skip
+ Verify SLAAC Property ${True} ${2}
+
+
Configure Invalid Static IPv6 And Verify
[Documentation] Configure invalid static IPv6 and verify.
[Tags] Configure_Invalid_Static_IPv6_And_Verify
@@ -209,7 +227,6 @@
${ipv6_multi_short} ${test_prefix_length} ${HTTP_BAD_REQUEST}
-
Configure IPv6 Static Default Gateway And Verify
[Documentation] Configure IPv6 static default gateway and verify.
[Tags] Configure_IPv6_Static_Default_Gateway_And_Verify
@@ -924,14 +941,15 @@
Set SLAAC Configuration State And Verify
- [Documentation] Set SLAAC configuration state and verify.
+ [Documentation] Set SLAAC configuration state.
[Arguments] ${slaac_state} ${valid_status_codes}=[${HTTP_OK},${HTTP_ACCEPTED},${HTTP_NO_CONTENT}]
- ... ${channel_number}=${CHANNEL_NUMBER}
+ ... ${channel_number}=${CHANNEL_NUMBER} ${is_slaac_verify_state}=${True}
# Description of argument(s):
- # slaac_state SLAAC state('True' or 'False').
- # valid_status_code Expected valid status codes.
- # channel_number Channel number 1(eth0) or 2(eth1).
+ # slaac_state SLAAC state('True' or 'False').
+ # valid_status_code Expected valid status codes.
+ # channel_number Channel number 1(eth0) or 2(eth1).
+ # is_slaac_verify_state Flag to check verification is required.
${active_channel_config}= Get Active Channel Config
${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']}
@@ -939,6 +957,18 @@
${data}= Set Variable If ${slaac_state} == ${False} ${DISABLE_SLAAC} ${ENABLE_SLAAC}
${resp}= Redfish.Patch ${REDFISH_NW_ETH_IFACE}${ethernet_interface}
... body=${data} valid_status_codes=${valid_status_codes}
+ IF ${is_slaac_verify_state}
+ Verify SLAAC Property ${slaac_state} ${channel_number}
+ END
+
+
+Verify SLAAC Property
+ [Documentation] Verify SLAAC property.
+ [Arguments] ${slaac_state} ${channel_number}=${CHANNEL_NUMBER}
+
+ # Description of argument(s):
+ # slaac_state SLAAC state('True' or 'False').
+ # channel_number Channel number 1(eth0) or 2(eth1).
# Verify SLAAC is set correctly.
${resp}= Redfish.Get ${REDFISH_NW_ETH_IFACE}${ethernet_interface}
@@ -948,6 +978,7 @@
Fail msg=SLAAC not set properly.
END
+
Set And Verify DHCPv6 Property
[Documentation] Set DHCPv6 property and verify.
[Arguments] ${dhcpv6_operating_mode}=${Disabled} ${channel_number}=${CHANNEL_NUMBER}