linux-aspeed: Move to v5.1

Current list of out-of-tree patches:

Alexander Amelkin (1):
      mtd: spi-nor: fix options for mx66l51235f

Alexander Soldatov (1):
      hwmon (occ): Add temp sensor value check

Andrew Jeffery (8):
      dt-bindings: hwmon: pmbus: Add Maxim MAX31785 documentation
      pmbus (max31785): Add support for devicetree configuration
      pmbus (core): One-shot retries for failure to set page
      pmbus (core): Use driver callbacks in pmbus_get_fan_rate()
      pmbus (max31785): Wrap all I2C accessors in one-shot failure handlers
      soc: aspeed: Miscellaneous control interfaces
      ARM: dts: aspeed: witherspoon: Update max31785 node
      ARM: dts: aspeed-g5: Expose VGA and SuperIO scratch registers

Andrew Peng (1):
      ARM: dts: aspeed: Adding Lenovo Hr630 BMC

Benjamin Fair (1):
      net: npcm: use bitmap functions on link mode params

Benjamin Herrenschmidt (1):
      ARM: dts: aspeed: Add Power9 and Power9 CFAM description

Christopher Bostic (1):
      iio: dps310: Temperature measurement errata

Cyril Bur (1):
      misc: Add ASPEED mbox driver

Cédric Le Goater (11):
      mtd: spi-nor: aspeed: use command mode for reads
      mtd: spi-nor: aspeed: add support for SPI dual IO read mode
      mtd: spi-nor: aspeed: link controller with the ahb clock
      mtd: spi-nor: aspeed: optimize read mode
      mtd: spi-nor: aspeed: limit the maximum SPI frequency
      /dev/mem: add a devmem kernel parameter to activate the device
      ARM: dts: aspeed: Add "spi-max-frequency" property
      mtd: spi-nor: aspeed: introduce a aspeed_smc_default_read() helper
      mtd: spi-nor: aspeed: clarify 4BYTE address mode mask
      mtd: spi-nor: aspeed: use memcpy_fromio() to capture the optimization buffer
      mtd: spi-nor: aspeed: add support for the 4B opcodes

Eddie James (10):
      ARM: dts: witherspoon: Enable vhub
      media: platform: Aspeed: Remove use of reset line
      media: platform: Aspeed: Make reserved memory optional
      media: dt-bindings: aspeed-video: Add missing memory-region property
      clk: Aspeed: Setup video engine clocking
      ARM: dts: aspeed-g5: Add video engine
      ARM: dts: witherspoon: Enable video engine
      ARM: dts: romulus: Enable video engine
      hwmon (occ): Store error condition for rate-limited polls
      hwmon (occ): Prevent sysfs error attribute from returning error

Edward A. James (1):
      ARM: dts: Aspeed: Witherspoon: Update BMC partitioning

Jae Hyun Yoo (19):
      dt-bindings: Add a document of PECI subsystem
      Documentation: ioctl: Add ioctl numbers for PECI subsystem
      peci: Add support for PECI bus driver core
      dt-bindings: Add a document of PECI adapter driver for ASPEED AST24xx/25xx SoCs
      peci: Add a PECI adapter driver for Aspeed AST24xx/AST25xx
      dt-bindings: mfd: Add a document for PECI client MFD
      mfd: intel-peci-client: Add PECI client MFD driver
      Documentation: hwmon: Add documents for PECI hwmon client drivers
      hwmon: Add PECI cputemp driver
      hwmon: Add PECI dimmtemp driver
      Add maintainers for the PECI subsystem
      ARM: dts: aspeed: peci: Add PECI node
      media: platform: aspeed: fix a kernel warning on clk control
      media: platform: aspeed: refine clock control logic
      media: platform: aspeed: change irq to threaded irq
      media: aspeed: remove IRQF_SHARED flag
      media: aspeed: reduce noisy log printing outs
      media: aspeed: remove checking of VE_INTERRUPT_CAPTURE_COMPLETE
      media: aspeed: refine interrupt handling logic

Joel Stanley (20):
      iio: Add driver for Infineon DPS310
      ARM: dts: aspeed-ast2500: Update flash layout
      ARM: dts: aspeed: Add LPC mailbox node
      ARM: dts: aspeed: Enable mbox
      ARM: dts: aspeed-g4: Expose SuperIO scratch registers
      ARM: dts: aspeed-g5: Add resets and clocks to GFX node
      ARM: dts: aspeed: Enable the GFX IP
      ARM: dts: aspeed: Add RTC node
      ARM: dts: aspeed: Rename flash-controller nodes
      ARM: config: aspeed: Update defconfigs
      ARM: config: aspeed-g5: Add video engine driver
      ARM: dts: npcm: Remove use of skeleton.dtsi
      dt-bindings: gpu: Add ASPEED GFX bindings document
      drm: Add ASPEED GFX driver
      drm: aspeed: Clean up Kconfig options
      dt-bindings: rtc: Add on-chip ASPEED RTC documentation
      rtc: Add ASPEED RTC driver
      ARM: config: aspeed: Add P2A and EDAC drivers
      ARM: config: aspeed-g5: Remove unused gadget drivers
      ARM: config: aspeed-g5: Add ISL68137 and IR38064

Lei YU (2):
      ARM: dts: palmetto: Fix flash_memory region
      hwmon (occ): Fix extended status bits

Maxim Sloyko (3):
      hwmon: (pmbus/ir38064): Add driver for Infineon IR38064 Voltage Regulator
      ARM: dts: aspeed: zaius: add Infineon and Intersil regulators
      hwmon: (pmbus/isl68137) Add driver for Intersil ISL68137 PWM Controller

Patrick Venture (7):
      ARM: dts: aspeed: zaius: Fix intersil compatibles
      dt-bindings: misc: aspeed-p2a-ctrl: add support
      drivers/misc: Add Aspeed P2A control driver
      ARM: dts: aspeed: Add aspeed-p2a-ctrl node
      ARM: dts: aspeed: quanta-q71: Enable p2a node
      dt-bindings: Add ir38064 as a trivial device
      dt-bindings: Add isl68137 as a trivial device

Robert Lippert (2):
      ARM: dts: aspeed: zaius: update 12V brick I2C address
      ARM: dts: aspeed: zaius: fixed I2C bus numbers for pcie slots

Tomer Maimon (18):
      dts: npcm7xx: Modify NPCM7xx device tree
      clk: nuvoton: add npcm750 clock function prototype initialization
      dt-binding: mtd: add NPCM FIU controller
      mtd: spi-nor: add NPCM FIU controller driver
      dt-bindings: i2c: npcm7xx: add binding for i2c controller
      i2c: npcm: driver for Poleg i2c controller
      dt-binding: bmc: Add NPCM7xx LPC BPC documentation
      misc: npcm7xx-lpc-bpc: add NPCM7xx BIOS post code driver
      dt-binding: bmc: add npcm7xx pci mailbox document
      misc: mbox: add npcm7xx pci mailbox driver
      dt-binding: net: document NPCM7xx EMC DT bindings
      net: npcm: add NPCM7xx Ethernet MAC controller
      ARM: npcm: add defconfig for Nuvoton NPCM7xx BMC
      ARM: dts: npcm7xx: Update device tree
      dt-binding: peci: add NPCM PECI documentation
      peci: npcm: add NPCM PECI driver
      ARM: dts: npcm7xx: Add PECI description
      ARM: config: npcm7xx: Enable PECI driver

Vijay Khemka (1):
      misc: aspeed-lpc-ctrl: make parameter optional

krzysztof.adamski@nokia.com (1):
      pmbus: support for custom sysfs attributes

(From meta-aspeed rev: a1594746d761ae3fd57c8e8419c8129e78b6634a)

Change-Id: I83486a54d00afb6162ab1a3c9ee3a082241f109b
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
1 file changed
tree: 05c29a6f9c6d518c16e4f392c0c0e0d1c3c98f13
  1. .github/
  2. meta-arm/
  3. meta-aspeed/
  4. meta-evb/
  5. meta-facebook/
  6. meta-google/
  7. meta-hxt/
  8. meta-ibm/
  9. meta-ingrasys/
  10. meta-inspur/
  11. meta-intel/
  12. meta-inventec/
  13. meta-mellanox/
  14. meta-nuvoton/
  15. meta-openembedded/
  16. meta-openpower/
  17. meta-phosphor/
  18. meta-portwell/
  19. meta-qualcomm/
  20. meta-quanta/
  21. meta-raspberrypi/
  22. meta-security/
  23. meta-x86/
  24. meta-xilinx/
  25. poky/
  26. .gitignore
  27. .gitreview
  28. .templateconf
  29. MAINTAINERS
  30. openbmc-env
  31. README.md
  32. setup
README.md

OpenBMC

Build Status

The OpenBMC project can be described as a Linux distribution for embedded devices that have a BMC; typically, but not limited to, things like servers, top of rack switches or RAID appliances. The OpenBMC stack uses technologies such as Yocto, OpenEmbedded, systemd, and D-Bus to allow easy customization for your server platform.

Setting up your OpenBMC project

1) Prerequisite

  • Ubuntu 14.04
sudo apt-get install -y git build-essential libsdl1.2-dev texinfo gawk chrpath diffstat
  • Fedora 28
sudo dnf install -y git patch diffstat texinfo chrpath SDL-devel bitbake \
    rpcgen perl-Thread-Queue perl-bignum perl-Crypt-OpenSSL-Bignum
sudo dnf groupinstall "C Development Tools and Libraries"

2) Download the source

git clone git@github.com:openbmc/openbmc.git
cd openbmc

3) Target your hardware

Any build requires an environment variable known as TEMPLATECONF to be set to a hardware target. You can see all of the known targets with find meta-* -name local.conf.sample. Choose the hardware target and then move to the next step. Additional examples can be found in the OpenBMC Cheatsheet

MachineTEMPLATECONF
Palmettometa-ibm/meta-palmetto/conf
Zaiusmeta-ingrasys/meta-zaius/conf
Witherspoonmeta-ibm/meta-witherspoon/conf
Romulusmeta-ibm/meta-romulus/conf

As an example target Palmetto

export TEMPLATECONF=meta-ibm/meta-palmetto/conf

4) Build

. openbmc-env
bitbake obmc-phosphor-image

Additional details can be found in the docs repository.

Build Validation and Testing

Commits submitted by members of the OpenBMC GitHub community are compiled and tested via our Jenkins server. Commits are run through two levels of testing. At the repository level the makefile make check directive is run. At the system level, the commit is built into a firmware image and run with an arm-softmmu QEMU model against a barrage of CI tests.

Commits submitted by non-members do not automatically proceed through CI testing. After visual inspection of the commit, a CI run can be manually performed by the reviewer.

Automated testing against the QEMU model along with supported systems are performed. The OpenBMC project uses the Robot Framework for all automation. Our complete test repository can be found here.

Submitting Patches

Support of additional hardware and software packages is always welcome. Please follow the contributing guidelines when making a submission. It is expected that contributions contain test cases.

Bug Reporting

Issues are managed on GitHub. It is recommended you search through the issues before opening a new one.

Features of OpenBMC

Feature List

  • Host management: Power, Cooling, LEDs, Inventory, Events, Watchdog
  • Full IPMI 2.0 Compliance with DCMI
  • Code Update Support for multiple BMC/BIOS images
  • Web-based user interface
  • REST interfaces
  • D-Bus based interfaces
  • SSH based SOL
  • Remote KVM
  • Hardware Simulation
  • Automated Testing

Features In Progress

  • OpenCompute Redfish Compliance
  • User management
  • Virtual media
  • Verified Boot

Features Requested but need help

  • OpenBMC performance monitoring

Finding out more

Dive deeper into OpenBMC by opening the docs repository.

Contact