diff --git a/poky/documentation/toaster-manual/history.rst b/poky/documentation/toaster-manual/history.rst
new file mode 100644
index 0000000..027b343
--- /dev/null
+++ b/poky/documentation/toaster-manual/history.rst
@@ -0,0 +1,46 @@
+.. SPDX-License-Identifier: CC-BY-2.0-UK
+
+***********************
+Manual Revision History
+***********************
+
+.. list-table::
+   :widths: 10 15 40
+   :header-rows: 1
+
+   * - Revision
+     - Date
+     - Note
+   * - 1.8
+     - April 2015
+     - The initial document released with the Yocto Project 1.8 Release
+   * - 2.0
+     - October 2015
+     - Released with the Yocto Project 2.0 Release.
+   * - 2.1
+     - April 2016
+     - Released with the Yocto Project 2.1 Release.
+   * - 2.2
+     - October 2016
+     - Released with the Yocto Project 2.2 Release.
+   * - 2.3
+     - May 2017
+     - Released with the Yocto Project 2.3 Release.
+   * - 2.4
+     - October 2017
+     - Released with the Yocto Project 2.4 Release.
+   * - 2.5
+     - May 2018
+     - Released with the Yocto Project 2.5 Release.
+   * - 2.6
+     - November 2018
+     - Released with the Yocto Project 2.6 Release.
+   * - 2.7
+     - May 2019
+     - Released with the Yocto Project 2.7 Release.
+   * - 3.0
+     - October 2019
+     - Released with the Yocto Project 3.0 Release.
+   * - 3.1
+     - April 2020
+     - Released with the Yocto Project 3.1 Release.
diff --git a/poky/documentation/toaster-manual/toaster-manual-intro.rst b/poky/documentation/toaster-manual/toaster-manual-intro.rst
new file mode 100644
index 0000000..0b7cd41
--- /dev/null
+++ b/poky/documentation/toaster-manual/toaster-manual-intro.rst
@@ -0,0 +1,105 @@
+.. SPDX-License-Identifier: CC-BY-2.0-UK
+
+************
+Introduction
+************
+
+Toaster is a web interface to the Yocto Project's
+:term:`OpenEmbedded Build System`. The interface
+enables you to configure and run your builds. Information about builds
+is collected and stored in a database. You can use Toaster to configure
+and start builds on multiple remote build servers.
+
+.. _intro-features:
+
+Toaster Features
+================
+
+Toaster allows you to configure and run builds, and it provides
+extensive information about the build process.
+
+-  *Configure and Run Builds:* You can use the Toaster web interface to
+   configure and start your builds. Builds started using the Toaster web
+   interface are organized into projects. When you create a project, you
+   are asked to select a release, or version of the build system you
+   want to use for the project builds. As shipped, Toaster supports
+   Yocto Project releases 1.8 and beyond. With the Toaster web
+   interface, you can:
+
+   -  Browse layers listed in the various
+      :ref:`layer sources <toaster-manual/toaster-manual-reference:layer source>`
+      that are available in your project (e.g. the OpenEmbedded Layer Index at
+      http://layers.openembedded.org/layerindex/).
+
+   -  Browse images, recipes, and machines provided by those layers.
+
+   -  Import your own layers for building.
+
+   -  Add and remove layers from your configuration.
+
+   -  Set configuration variables.
+
+   -  Select a target or multiple targets to build.
+
+   -  Start your builds.
+
+   Toaster also allows you to configure and run your builds from the
+   command line, and switch between the command line and the web
+   interface at any time. Builds started from the command line appear
+   within a special Toaster project called "Command line builds".
+
+-  *Information About the Build Process:* Toaster also records extensive
+   information about your builds. Toaster collects data for builds you
+   start from the web interface and from the command line as long as
+   Toaster is running.
+
+   .. note::
+
+      You must start Toaster before the build or it will not collect
+      build data.
+
+   With Toaster you can:
+
+   -  See what was built (recipes and packages) and what packages were
+      installed into your final image.
+
+   -  Browse the directory structure of your image.
+
+   -  See the value of all variables in your build configuration, and
+      which files set each value.
+
+   -  Examine error, warning, and trace messages to aid in debugging.
+
+   -  See information about the BitBake tasks executed and reused during
+      your build, including those that used shared state.
+
+   -  See dependency relationships between recipes, packages, and tasks.
+
+   -  See performance information such as build time, task time, CPU
+      usage, and disk I/O.
+
+For an overview of Toaster shipped with the Yocto Project &DISTRO;
+Release, see the "`Toaster - Yocto Project
+2.2 <https://youtu.be/BlXdOYLgPxA>`__" video.
+
+.. _toaster-installation-options:
+
+Installation Options
+====================
+
+You can set Toaster up to run as a local instance or as a shared hosted
+service.
+
+When Toaster is set up as a local instance, all the components reside on
+a single build host. Fundamentally, a local instance of Toaster is
+suited for a single user developing on a single build host.
+
+.. image:: figures/simple-configuration.png
+   :align: center
+
+Toaster as a hosted service is suited for multiple users developing
+across several build hosts. When Toaster is set up as a hosted service,
+its components can be spread across several machines:
+
+.. image:: figures/hosted-service.png
+   :align: center
diff --git a/poky/documentation/toaster-manual/toaster-manual-reference.rst b/poky/documentation/toaster-manual/toaster-manual-reference.rst
new file mode 100644
index 0000000..e95536e
--- /dev/null
+++ b/poky/documentation/toaster-manual/toaster-manual-reference.rst
@@ -0,0 +1,662 @@
+.. SPDX-License-Identifier: CC-BY-2.0-UK
+
+**********************
+Concepts and Reference
+**********************
+
+In order to configure and use Toaster, you should understand some
+concepts and have some basic command reference material available. This
+final chapter provides conceptual information on layer sources,
+releases, and JSON configuration files. Also provided is a quick look at
+some useful ``manage.py`` commands that are Toaster-specific.
+Information on ``manage.py`` commands does exist across the Web and the
+information in this manual by no means attempts to provide a command
+comprehensive reference.
+
+Layer Source
+============
+
+In general, a "layer source" is a source of information about existing
+layers. In particular, we are concerned with layers that you can use
+with the Yocto Project and Toaster. This chapter describes a particular
+type of layer source called a "layer index."
+
+A layer index is a web application that contains information about a set
+of custom layers. A good example of an existing layer index is the
+OpenEmbedded Layer Index. A public instance of this layer index exists
+at http://layers.openembedded.org. You can find the code for this
+layer index's web application at
+http://git.yoctoproject.org/cgit/cgit.cgi/layerindex-web/.
+
+When you tie a layer source into Toaster, it can query the layer source
+through a
+`REST <http://en.wikipedia.org/wiki/Representational_state_transfer>`__
+API, store the information about the layers in the Toaster database, and
+then show the information to users. Users are then able to view that
+information and build layers from Toaster itself without worrying about
+cloning or editing the BitBake layers configuration file
+``bblayers.conf``.
+
+Tying a layer source into Toaster is convenient when you have many
+custom layers that need to be built on a regular basis by a community of
+developers. In fact, Toaster comes pre-configured with the OpenEmbedded
+Metadata Index.
+
+.. note::
+
+   You do not have to use a layer source to use Toaster. Tying into a
+   layer source is optional.
+
+.. _layer-source-using-with-toaster:
+
+Setting Up and Using a Layer Source
+-----------------------------------
+
+To use your own layer source, you need to set up the layer source and
+then tie it into Toaster. This section describes how to tie into a layer
+index in a manner similar to the way Toaster ties into the OpenEmbedded
+Metadata Index.
+
+Understanding Your Layers
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+The obvious first step for using a layer index is to have several custom
+layers that developers build and access using the Yocto Project on a
+regular basis. This set of layers needs to exist and you need to be
+familiar with where they reside. You will need that information when you
+set up the code for the web application that "hooks" into your set of
+layers.
+
+For general information on layers, see the
+":ref:`overview-manual/overview-manual-yp-intro:the yocto project layer model`"
+section in the Yocto Project Overview and Concepts Manual. For information on how
+to create layers, see the ":ref:`dev-manual/dev-manual-common-tasks:understanding and creating layers`"
+section in the Yocto Project Development Tasks Manual.
+
+.. _configuring-toaster-to-hook-into-your-layer-source:
+
+Configuring Toaster to Hook Into Your Layer Index
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+If you want Toaster to use your layer index, you must host the web
+application in a server to which Toaster can connect. You also need to
+give Toaster the information about your layer index. In other words, you
+have to configure Toaster to use your layer index. This section
+describes two methods by which you can configure and use your layer
+index.
+
+In the previous section, the code for the OpenEmbedded Metadata Index
+(i.e. http://layers.openembedded.org) was referenced. You can use
+this code, which is at
+http://git.yoctoproject.org/cgit/cgit.cgi/layerindex-web/, as a
+base to create your own layer index.
+
+Use the Administration Interface
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+Access the administration interface through a browser by entering the
+URL of your Toaster instance and adding "``/admin``" to the end of the
+URL. As an example, if you are running Toaster locally, use the
+following URL::
+
+   http://127.0.0.1:8000/admin
+
+The administration interface has a "Layer sources" section that includes
+an "Add layer source" button. Click that button and provide the required
+information. Make sure you select "layerindex" as the layer source type.
+
+Use the Fixture Feature
+^^^^^^^^^^^^^^^^^^^^^^^
+
+The Django fixture feature overrides the default layer server when you
+use it to specify a custom URL. To use the fixture feature, create (or
+edit) the file ``bitbake/lib/toaster.orm/fixtures/custom.xml``, and then
+set the following Toaster setting to your custom URL:
+
+.. code-block:: xml
+
+   <?xml version="1.0" ?>
+   <django-objects version="1.0">
+      <object model="orm.toastersetting" pk="100">
+         <field name="name" type="CharField">CUSTOM_LAYERINDEX_SERVER</field>
+         <field name="value" type="CharField">https://layers.my_organization.org/layerindex/branch/master/layers/</field>
+      </object>
+   <django-objects>
+
+When you start Toaster for the first time, or
+if you delete the file ``toaster.sqlite`` and restart, the database will
+populate cleanly from this layer index server.
+
+Once the information has been updated, verify the new layer information
+is available by using the Toaster web interface. To do that, visit the
+"All compatible layers" page inside a Toaster project. The layers from
+your layer source should be listed there.
+
+If you change the information in your layer index server, refresh the
+Toaster database by running the following command:
+
+.. code-block:: shell
+
+   $ bitbake/lib/toaster/manage.py lsupdates
+
+
+If Toaster can reach the API URL, you should see a message telling you that
+Toaster is updating the layer source information.
+
+.. _toaster-releases:
+
+Releases
+========
+
+When you create a Toaster project using the web interface, you are asked
+to choose a "Release." In the context of Toaster, the term "Release"
+refers to a set of layers and a BitBake version the OpenEmbedded build
+system uses to build something. As shipped, Toaster is pre-configured
+with releases that correspond to Yocto Project release branches.
+However, you can modify, delete, and create new releases according to
+your needs. This section provides some background information on
+releases.
+
+.. _toaster-releases-supported:
+
+Pre-Configured Releases
+-----------------------
+
+As shipped, Toaster is configured to use a specific set of releases. Of
+course, you can always configure Toaster to use any release. For
+example, you might want your project to build against a specific commit
+of any of the "out-of-the-box" releases. Or, you might want your project
+to build against different revisions of OpenEmbedded and BitBake.
+
+As shipped, Toaster is configured to work with the following releases:
+
+-  *Yocto Project &DISTRO; "&DISTRO_NAME;" or OpenEmbedded "&DISTRO_NAME;":*
+   This release causes your Toaster projects to build against the head
+   of the &DISTRO_NAME_NO_CAP; branch at
+   https://git.yoctoproject.org/cgit/cgit.cgi/poky/log/?h=&DISTRO_NAME_NO_CAP; or
+   http://git.openembedded.org/openembedded-core/commit/?h=&DISTRO_NAME_NO_CAP;.
+
+-  *Yocto Project "Master" or OpenEmbedded "Master":* This release
+   causes your Toaster Projects to build against the head of the master
+   branch, which is where active development takes place, at
+   https://git.yoctoproject.org/cgit/cgit.cgi/poky/log/ or
+   http://git.openembedded.org/openembedded-core/log/.
+
+-  *Local Yocto Project or Local OpenEmbedded:* This release causes your
+   Toaster Projects to build against the head of the ``poky`` or
+   ``openembedded-core`` clone you have local to the machine running
+   Toaster.
+
+Configuring Toaster
+===================
+
+In order to use Toaster, you must configure the database with the
+default content. The following subsections describe various aspects of
+Toaster configuration.
+
+Configuring the Workflow
+------------------------
+
+The ``bldcontrol/management/commands/checksettings.py`` file controls
+workflow configuration. The following steps outline the process to
+initially populate this database.
+
+1. The default project settings are set from
+   ``orm/fixtures/settings.xml``.
+
+2. The default project distro and layers are added from
+   ``orm/fixtures/poky.xml`` if poky is installed. If poky is not
+   installed, they are added from ``orm/fixtures/oe-core.xml``.
+
+3. If the ``orm/fixtures/custom.xml`` file exists, then its values are
+   added.
+
+4. The layer index is then scanned and added to the database.
+
+Once these steps complete, Toaster is set up and ready to use.
+
+Customizing Pre-Set Data
+------------------------
+
+The pre-set data for Toaster is easily customizable. You can create the
+``orm/fixtures/custom.xml`` file to customize the values that go into to
+the database. Customization is additive, and can either extend or
+completely replace the existing values.
+
+You use the ``orm/fixtures/custom.xml`` file to change the default
+project settings for the machine, distro, file images, and layers. When
+creating a new project, you can use the file to define the offered
+alternate project release selections. For example, you can add one or
+more additional selections that present custom layer sets or distros,
+and any other local or proprietary content.
+
+Additionally, you can completely disable the content from the
+``oe-core.xml`` and ``poky.xml`` files by defining the section shown
+below in the ``settings.xml`` file. For example, this option is
+particularly useful if your custom configuration defines fewer releases
+or layers than the default fixture files.
+
+The following example sets "name" to "CUSTOM_XML_ONLY" and its value to
+"True".
+
+.. code-block:: xml
+
+   <object model="orm.toastersetting" pk="99">
+      <field type="CharField" name="name">CUSTOM_XML_ONLY</field>
+      <field type="CharField" name="value">True</field>
+   </object>
+
+Understanding Fixture File Format
+---------------------------------
+
+The following is an overview of the file format used by the
+``oe-core.xml``, ``poky.xml``, and ``custom.xml`` files.
+
+The following subsections describe each of the sections in the fixture
+files, and outline an example section of the XML code. you can use to
+help understand this information and create a local ``custom.xml`` file.
+
+Defining the Default Distro and Other Values
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+This section defines the default distro value for new projects. By
+default, it reserves the first Toaster Setting record "1". The following
+demonstrates how to set the project default value for
+:term:`DISTRO`:
+
+.. code-block:: xml
+
+   <!-- Set the project default value for DISTRO -->
+   <object model="orm.toastersetting" pk="1">
+      <field type="CharField" name="name">DEFCONF_DISTRO</field>
+      <field type="CharField" name="value">poky</field>
+   </object>
+
+You can override
+other default project values by adding additional Toaster Setting
+sections such as any of the settings coming from the ``settings.xml``
+file. Also, you can add custom values that are included in the BitBake
+environment. The "pk" values must be unique. By convention, values that
+set default project values have a "DEFCONF" prefix.
+
+Defining BitBake Version
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+The following defines which version of BitBake is used for the following
+release selection:
+
+.. code-block:: xml
+
+   <!-- Bitbake versions which correspond to the metadata release -->
+   <object model="orm.bitbakeversion" pk="1">
+      <field type="CharField" name="name">&DISTRO_NAME_NO_CAP;</field>
+      <field type="CharField" name="giturl">git://git.yoctoproject.org/poky</field>
+      <field type="CharField" name="branch">&DISTRO_NAME_NO_CAP;</field>
+      <field type="CharField" name="dirpath">bitbake</field>
+   </object>
+
+.. _defining-releases:
+
+Defining Release
+~~~~~~~~~~~~~~~~
+
+The following defines the releases when you create a new project:
+
+.. code-block:: xml
+
+   <!-- Releases available -->
+   <object model="orm.release" pk="1">
+      <field type="CharField" name="name">&DISTRO_NAME_NO_CAP;</field>
+      <field type="CharField" name="description">Yocto Project &DISTRO; "&DISTRO_NAME;"</field>
+      <field rel="ManyToOneRel" to="orm.bitbakeversion" name="bitbake_version">1</field>
+      <field type="CharField" name="branch_name">&DISTRO_NAME_NO_CAP;</field>
+      <field type="TextField" name="helptext">Toaster will run your builds using the tip of the <a href="http://git.yoctoproject.org/cgit/cgit.cgi/poky/log/?h=&DISTRO_NAME_NO_CAP;">Yocto Project &DISTRO_NAME; branch</a>.</field>
+   </object>
+
+The "pk" value must match the above respective BitBake version record.
+
+Defining the Release Default Layer Names
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+The following defines the default layers for each release:
+
+.. code-block:: xml
+
+   <!-- Default project layers for each release -->
+   <object model="orm.releasedefaultlayer" pk="1">
+      <field rel="ManyToOneRel" to="orm.release" name="release">1</field>
+      <field type="CharField" name="layer_name">openembedded-core</field>
+   </object>
+
+The 'pk' values in the example above should start at "1" and increment
+uniquely. You can use the same layer name in multiple releases.
+
+Defining Layer Definitions
+~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Layer definitions are the most complex. The following defines each of
+the layers, and then defines the exact layer version of the layer used
+for each respective release. You must have one ``orm.layer`` entry for
+each layer. Then, with each entry you need a set of
+``orm.layer_version`` entries that connects the layer with each release
+that includes the layer. In general all releases include the layer.
+
+.. code-block:: xml
+
+   <object model="orm.layer" pk="1">
+      <field type="CharField" name="name">openembedded-core</field>
+      <field type="CharField" name="layer_index_url"></field>
+      <field type="CharField" name="vcs_url">git://git.yoctoproject.org/poky</field>
+      <field type="CharField" name="vcs_web_url">http://git.yoctoproject.org/cgit/cgit.cgi/poky</field>
+      <field type="CharField" name="vcs_web_tree_base_url">http://git.yoctoproject.org/cgit/cgit.cgi/poky/tree/%path%?h=%branch%</field>
+      <field type="CharField" name="vcs_web_file_base_url">http://git.yoctoproject.org/cgit/cgit.cgi/poky/tree/%path%?h=%branch%</field>
+   </object>
+   <object model="orm.layer_version" pk="1">
+      <field rel="ManyToOneRel" to="orm.layer" name="layer">1</field>
+      <field type="IntegerField" name="layer_source">0</field>
+      <field rel="ManyToOneRel" to="orm.release" name="release">1</field>
+      <field type="CharField" name="branch">&DISTRO_NAME_NO_CAP;</field>
+      <field type="CharField" name="dirpath">meta</field>
+   </object> <object model="orm.layer_version" pk="2">
+      <field rel="ManyToOneRel" to="orm.layer" name="layer">1</field>
+      <field type="IntegerField" name="layer_source">0</field>
+      <field rel="ManyToOneRel" to="orm.release" name="release">2</field>
+      <field type="CharField" name="branch">HEAD</field>
+      <field type="CharField" name="commit">HEAD</field>
+      <field type="CharField" name="dirpath">meta</field>
+   </object>
+   <object model="orm.layer_version" pk="3">
+      <field rel="ManyToOneRel" to="orm.layer" name="layer">1</field>
+      <field type="IntegerField" name="layer_source">0</field>
+      <field rel="ManyToOneRel" to="orm.release" name="release">3</field>
+      <field type="CharField" name="branch">master</field>
+      <field type="CharField" name="dirpath">meta</field>
+   </object>
+
+The layer "pk" values above must be unique, and typically start at "1". The
+layer version "pk" values must also be unique across all layers, and typically
+start at "1".
+
+Remote Toaster Monitoring
+=========================
+
+Toaster has an API that allows remote management applications to
+directly query the state of the Toaster server and its builds in a
+machine-to-machine manner. This API uses the
+`REST <http://en.wikipedia.org/wiki/Representational_state_transfer>`__
+interface and the transfer of JSON files. For example, you might monitor
+a build inside a container through well supported known HTTP ports in
+order to easily access a Toaster server inside the container. In this
+example, when you use this direct JSON API, you avoid having web page
+parsing against the display the user sees.
+
+Checking Health
+---------------
+
+Before you use remote Toaster monitoring, you should do a health check.
+To do this, ping the Toaster server using the following call to see if
+it is still alive::
+
+   http://host:port/health
+
+Be sure to provide values for host and port. If the server is alive, you will
+get the response HTML:
+
+.. code-block:: html
+
+   <!DOCTYPE html>
+   <html lang="en">
+      <head><title>Toaster Health</title></head>
+      <body>Ok</body>
+   </html>
+
+Determining Status of Builds in Progress
+----------------------------------------
+
+Sometimes it is useful to determine the status of a build in progress.
+To get the status of pending builds, use the following call::
+
+   http://host:port/toastergui/api/building
+
+Be sure to provide values for host and port. The output is a JSON file that
+itemizes all builds in progress. This file includes the time in seconds since
+each respective build started as well as the progress of the cloning, parsing,
+and task execution. The following is sample output for a build in progress:
+
+.. code-block:: JSON
+
+   {"count": 1,
+    "building": [
+      {"machine": "beaglebone",
+        "seconds": "463.869",
+        "task": "927:2384",
+        "distro": "poky",
+        "clone": "1:1",
+        "id": 2,
+        "start": "2017-09-22T09:31:44.887Z",
+        "name": "20170922093200",
+        "parse": "818:818",
+        "project": "my_rocko",
+        "target": "core-image-minimal"
+      }]
+   }
+
+The JSON data for this query is returned in a
+single line. In the previous example the line has been artificially
+split for readability.
+
+Checking Status of Builds Completed
+-----------------------------------
+
+Once a build is completed, you get the status when you use the following
+call::
+
+   http://host:port/toastergui/api/builds
+
+Be sure to provide values for host and port. The output is a JSON file that
+itemizes all complete builds, and includes build summary information. The
+following is sample output for a completed build:
+
+.. code-block:: JSON
+
+   {"count": 1,
+    "builds": [
+      {"distro": "poky",
+         "errors": 0,
+         "machine": "beaglebone",
+         "project": "my_rocko",
+         "stop": "2017-09-22T09:26:36.017Z",
+         "target": "quilt-native",
+         "seconds": "78.193",
+         "outcome": "Succeeded",
+         "id": 1,
+         "start": "2017-09-22T09:25:17.824Z",
+         "warnings": 1,
+         "name": "20170922092618"
+      }]
+   }
+
+The JSON data for this query is returned in a single line. In the
+previous example the line has been artificially split for readability.
+
+Determining Status of a Specific Build
+--------------------------------------
+
+Sometimes it is useful to determine the status of a specific build. To
+get the status of a specific build, use the following call::
+
+   http://host:port/toastergui/api/build/ID
+
+Be sure to provide values for
+host, port, and ID. You can find the value for ID from the Builds
+Completed query. See the ":ref:`toaster-manual/toaster-manual-reference:checking status of builds completed`"
+section for more information.
+
+The output is a JSON file that itemizes the specific build and includes
+build summary information. The following is sample output for a specific
+build:
+
+.. code-block:: JSON
+
+   {"build":
+      {"distro": "poky",
+       "errors": 0,
+       "machine": "beaglebone",
+       "project": "my_rocko",
+       "stop": "2017-09-22T09:26:36.017Z",
+       "target": "quilt-native",
+       "seconds": "78.193",
+       "outcome": "Succeeded",
+       "id": 1,
+       "start": "2017-09-22T09:25:17.824Z",
+       "warnings": 1,
+       "name": "20170922092618",
+       "cooker_log": "/opt/user/poky/build-toaster-2/tmp/log/cooker/beaglebone/build_20170922_022607.991.log"
+      }
+   }
+
+The JSON data for this query is returned in a single line. In the
+previous example the line has been artificially split for readability.
+
+.. _toaster-useful-commands:
+
+Useful Commands
+===============
+
+In addition to the web user interface and the scripts that start and
+stop Toaster, command-line commands exist through the ``manage.py``
+management script. You can find general documentation on ``manage.py``
+at the
+`Django <https://docs.djangoproject.com/en/2.2/topics/settings/>`__
+site. However, several ``manage.py`` commands have been created that are
+specific to Toaster and are used to control configuration and back-end
+tasks. You can locate these commands in the
+:term:`Source Directory` (e.g. ``poky``) at
+``bitbake/lib/manage.py``. This section documents those commands.
+
+.. note::
+
+   -  When using ``manage.py`` commands given a default configuration,
+      you must be sure that your working directory is set to the
+      :term:`Build Directory`. Using
+      ``manage.py`` commands from the Build Directory allows Toaster to
+      find the ``toaster.sqlite`` file, which is located in the Build
+      Directory.
+
+   -  For non-default database configurations, it is possible that you
+      can use ``manage.py`` commands from a directory other than the
+      Build Directory. To do so, the ``toastermain/settings.py`` file
+      must be configured to point to the correct database backend.
+
+.. _toaster-command-buildslist:
+
+``buildslist``
+--------------
+
+The ``buildslist`` command lists all builds that Toaster has recorded.
+Access the command as follows:
+
+.. code-block:: shell
+
+   $ bitbake/lib/toaster/manage.py buildslist
+
+The command returns a list, which includes numeric
+identifications, of the builds that Toaster has recorded in the current
+database.
+
+You need to run the ``buildslist`` command first to identify existing
+builds in the database before using the
+:ref:`toaster-manual/toaster-manual-reference:\`\`builddelete\`\`` command. Here is an
+example that assumes default repository and build directory names:
+
+.. code-block:: shell
+
+   $ cd ~/poky/build
+   $ python ../bitbake/lib/toaster/manage.py buildslist
+
+If your Toaster database had only one build, the above
+:ref:`toaster-manual/toaster-manual-reference:\`\`buildslist\`\``
+command would return something like the following::
+
+   1: qemux86 poky core-image-minimal
+
+.. _toaster-command-builddelete:
+
+``builddelete``
+---------------
+
+The ``builddelete`` command deletes data associated with a build. Access
+the command as follows:
+
+.. code-block::
+
+   $ bitbake/lib/toaster/manage.py builddelete build_id
+
+The command deletes all the build data for the specified
+build_id. This command is useful for removing old and unused data from
+the database.
+
+Prior to running the ``builddelete`` command, you need to get the ID
+associated with builds by using the
+:ref:`toaster-manual/toaster-manual-reference:\`\`buildslist\`\`` command.
+
+.. _toaster-command-perf:
+
+``perf``
+--------
+
+The ``perf`` command measures Toaster performance. Access the command as
+follows:
+
+.. code-block:: shell
+
+   $ bitbake/lib/toaster/manage.py perf
+
+The command is a sanity check that returns page loading times in order to
+identify performance problems.
+
+.. _toaster-command-checksettings:
+
+``checksettings``
+-----------------
+
+The ``checksettings`` command verifies existing Toaster settings. Access
+the command as follows:
+
+.. code-block:: shell
+
+   $ bitbake/lib/toaster/manage.py checksettings
+
+Toaster uses settings that are based on the database to configure the
+building tasks. The ``checksettings`` command verifies that the database
+settings are valid in the sense that they have the minimal information
+needed to start a build.
+
+In order for the ``checksettings`` command to work, the database must be
+correctly set up and not have existing data. To be sure the database is
+ready, you can run the following:
+
+.. code-block:: shell
+
+   $ bitbake/lib/toaster/manage.py syncdb
+   $ bitbake/lib/toaster/manage.py migrate orm
+   $ bitbake/lib/toaster/manage.py migrate bldcontrol
+
+After running these commands, you can run the ``checksettings`` command.
+
+.. _toaster-command-runbuilds:
+
+``runbuilds``
+-------------
+
+The ``runbuilds`` command launches scheduled builds. Access the command
+as follows:
+
+.. code-block:: shell
+
+   $ bitbake/lib/toaster/manage.py runbuilds
+
+The ``runbuilds`` command checks if scheduled builds exist in the database
+and then launches them per schedule. The command returns after the builds
+start but before they complete. The Toaster Logging Interface records and
+updates the database when the builds complete.
diff --git a/poky/documentation/toaster-manual/toaster-manual-setup-and-use.rst b/poky/documentation/toaster-manual/toaster-manual-setup-and-use.rst
new file mode 100644
index 0000000..01c0dce
--- /dev/null
+++ b/poky/documentation/toaster-manual/toaster-manual-setup-and-use.rst
@@ -0,0 +1,651 @@
+.. SPDX-License-Identifier: CC-BY-2.0-UK
+.. Set default pygment highlighting to 'shell' for this document
+.. highlight:: shell
+
+****************************
+Setting Up and Using Toaster
+****************************
+
+Starting Toaster for Local Development
+======================================
+
+Once you have set up the Yocto Project and installed the Toaster system
+dependencies as described in the ":ref:`toaster-manual/toaster-manual-start:Preparing to Use
+Toaster`" chapter, you are ready to start
+Toaster.
+
+Navigate to the root of your
+:term:`Source Directory` (e.g. ``poky``)::
+
+   $ cd poky
+
+Once in that directory, source the build environment script::
+
+   $ source oe-init-build-env
+
+Next, from the build directory (e.g.
+``poky/build``), start Toaster using this command::
+
+   $ source toaster start
+
+You can now run your builds from the command line, or with Toaster
+as explained in section
+":ref:`toaster-manual/toaster-manual-setup-and-use:using the toaster web interface`".
+
+To access the Toaster web interface, open your favorite browser and
+enter the following::
+
+   http://127.0.0.1:8000
+
+Setting a Different Port
+========================
+
+By default, Toaster starts on port 8000. You can use the ``WEBPORT``
+parameter to set a different port. For example, the following command
+sets the port to "8400"::
+
+   $ source toaster start webport=8400
+
+Setting Up Toaster Without a Web Server
+=======================================
+
+You can start a Toaster environment without starting its web server.
+This is useful for the following:
+
+-  Capturing a command-line build's statistics into the Toaster database
+   for examination later.
+
+-  Capturing a command-line build's statistics when the Toaster server
+   is already running.
+
+-  Having one instance of the Toaster web server track and capture
+   multiple command-line builds, where each build is started in its own
+   "noweb" Toaster environment.
+
+The following commands show how to start a Toaster environment without
+starting its web server, perform BitBake operations, and then shut down
+the Toaster environment. Once the build is complete, you can close the
+Toaster environment. Before closing the environment, however, you should
+allow a few minutes to ensure the complete transfer of its BitBake build
+statistics to the Toaster database. If you have a separate Toaster web
+server instance running, you can watch this command-line build's
+progress and examine the results as soon as they are posted::
+
+   $ source toaster start noweb
+   $ bitbake target
+   $ source toaster stop
+
+Setting Up Toaster Without a Build Server
+=========================================
+
+You can start a Toaster environment with the "New Projects" feature
+disabled. Doing so is useful for the following:
+
+-  Sharing your build results over the web server while blocking others
+   from starting builds on your host.
+
+-  Allowing only local command-line builds to be captured into the
+   Toaster database.
+
+Use the following command to set up Toaster without a build server::
+
+   $ source toaster start nobuild webport=port
+
+Setting up External Access
+==========================
+
+By default, Toaster binds to the loop back address (i.e. ``localhost``),
+which does not allow access from external hosts. To allow external
+access, use the ``WEBPORT`` parameter to open an address that connects
+to the network, specifically the IP address that your NIC uses to
+connect to the network. You can also bind to all IP addresses the
+computer supports by using the shortcut "0.0.0.0:port".
+
+The following example binds to all IP addresses on the host::
+
+   $ source toaster start webport=0.0.0.0:8400
+
+This example binds to a specific IP address on the host's NIC::
+
+   $ source toaster start webport=192.168.1.1:8400
+
+The Directory for Cloning Layers
+================================
+
+Toaster creates a ``_toaster_clones`` directory inside your Source
+Directory (i.e. ``poky``) to clone any layers needed for your builds.
+
+Alternatively, if you would like all of your Toaster related files and
+directories to be in a particular location other than the default, you
+can set the ``TOASTER_DIR`` environment variable, which takes precedence
+over your current working directory. Setting this environment variable
+causes Toaster to create and use ``$TOASTER_DIR./_toaster_clones``.
+
+.. _toaster-the-build-directory:
+
+The Build Directory
+===================
+
+Toaster creates a build directory within your Source Directory (e.g.
+``poky``) to execute the builds.
+
+Alternatively, if you would like all of your Toaster related files and
+directories to be in a particular location, you can set the
+``TOASTER_DIR`` environment variable, which takes precedence over your
+current working directory. Setting this environment variable causes
+Toaster to use ``$TOASTER_DIR/build`` as the build directory.
+
+.. _toaster-creating-a-django-super-user:
+
+Creating a Django Superuser
+===========================
+
+Toaster is built on the `Django
+framework <https://www.djangoproject.com/>`__. Django provides an
+administration interface you can use to edit Toaster configuration
+parameters.
+
+To access the Django administration interface, you must create a
+superuser by following these steps:
+
+#. If you used ``pip3``, which is recommended, to set up the Toaster
+   system dependencies, you need be sure the local user path is in your
+   ``PATH`` list. To append the pip3 local user path, use the following
+   command::
+
+      $ export PATH=$PATH:$HOME/.local/bin
+
+#. From the directory containing the Toaster database, which by default
+   is the :term:`Build Directory`,
+   invoke the ``createsuperuser`` command from ``manage.py``::
+
+      $ cd ~/poky/build
+      $ ../bitbake/lib/toaster/manage.py createsuperuser
+
+#. Django prompts you for the username, which you need to provide.
+
+#. Django prompts you for an email address, which is optional.
+
+#. Django prompts you for a password, which you must provide.
+
+#. Django prompts you to re-enter your password for verification.
+
+After completing these steps, the following confirmation message
+appears::
+
+   Superuser created successfully.
+
+Creating a superuser allows you to access the Django administration
+interface through a browser. The URL for this interface is the same as
+the URL used for the Toaster instance with "/admin" on the end. For
+example, if you are running Toaster locally, use the following URL::
+
+   http://127.0.0.1:8000/admin
+
+You can use the Django administration interface to set Toaster configuration
+parameters such as the build directory, layer sources, default variable
+values, and BitBake versions.
+
+.. _toaster-setting-up-a-production-instance-of-toaster:
+
+Setting Up a Production Instance of Toaster
+===========================================
+
+You can use a production instance of Toaster to share the Toaster
+instance with remote users, multiple users, or both. The production
+instance is also the setup that can handle heavier loads on the web
+service. Use the instructions in the following sections to set up
+Toaster to run builds through the Toaster web interface.
+
+.. _toaster-production-instance-requirements:
+
+Requirements
+------------
+
+Be sure you meet the following requirements:
+
+.. note::
+
+   You must comply with all Apache, ``mod-wsgi``, and Mysql requirements.
+
+-  Have all the build requirements as described in the ":ref:`toaster-manual/toaster-manual-start:Preparing to
+   Use Toaster`" chapter.
+
+-  Have an Apache webserver.
+
+-  Have ``mod-wsgi`` for the Apache webserver.
+
+-  Use the Mysql database server.
+
+-  If you are using Ubuntu, run the following::
+
+      $ sudo apt-get install apache2 libapache2-mod-wsgi-py3 mysql-server python3-pip libmysqlclient-dev
+
+-  If you are using Fedora or a RedHat distribution, run the
+   following::
+
+      $ sudo dnf install httpd python3-mod_wsgi python3-pip mariadb-server mariadb-devel python3-devel
+
+-  If you are using openSUSE, run the following::
+
+      $ sudo zypper install apache2 apache2-mod_wsgi-python3 python3-pip mariadb mariadb-client python3-devel
+
+.. _toaster-installation-steps:
+
+Installation
+------------
+
+Perform the following steps to install Toaster:
+
+#.  Create toaster user and set its home directory to
+    ``/var/www/toaster``::
+
+      $ sudo /usr/sbin/useradd toaster -md /var/www/toaster -s /bin/false
+      $ sudo su - toaster -s /bin/bash
+
+#.  Checkout a copy of ``poky`` into the web server directory. You will
+    be using ``/var/www/toaster``::
+
+      $ git clone git://git.yoctoproject.org/poky
+      $ git checkout &DISTRO_NAME_NO_CAP;
+
+#.  Install Toaster dependencies using the --user flag which keeps the
+    Python packages isolated from your system-provided packages::
+
+      $ cd /var/www/toaster/
+      $ pip3 install --user -r ./poky/bitbake/toaster-requirements.txt
+      $ pip3 install --user mysqlclient
+
+    .. note::
+
+       Isolating these packages is not required but is recommended.
+       Alternatively, you can use your operating system's package
+       manager to install the packages.
+
+#.  Configure Toaster by editing
+    ``/var/www/toaster/poky/bitbake/lib/toaster/toastermain/settings.py``
+    as follows:
+
+    -  Edit the
+       `DATABASES <https://docs.djangoproject.com/en/2.2/ref/settings/#databases>`__
+       settings:
+
+       .. code-block:: python
+
+         DATABASES = {
+            'default': {
+               'ENGINE': 'django.db.backends.mysql',
+               'NAME': 'toaster_data',
+               'USER': 'toaster',
+               'PASSWORD': 'yourpasswordhere',
+               'HOST': 'localhost',
+               'PORT': '3306',
+            }
+         }
+
+    -  Edit the
+       `SECRET_KEY <https://docs.djangoproject.com/en/2.2/ref/settings/#std:setting-SECRET_KEY>`__:
+
+       .. code-block:: python
+
+         SECRET_KEY = 'your_secret_key'
+
+    -  Edit the
+       `STATIC_ROOT <https://docs.djangoproject.com/en/2.2/ref/settings/#std:setting-STATIC_ROOT>`__:
+
+      .. code-block:: python
+
+         STATIC_ROOT = '/var/www/toaster/static_files/'
+
+#.  Add the database and user to the ``mysql`` server defined earlier::
+
+      $ mysql -u root -p
+      mysql> CREATE DATABASE toaster_data;
+      mysql> CREATE USER 'toaster'@'localhost' identified by 'yourpasswordhere';
+      mysql> GRANT all on toaster_data.\* to 'toaster'@'localhost';
+      mysql> quit
+
+#.  Get Toaster to create the database schema, default data, and gather
+    the statically-served files::
+
+      $ cd /var/www/toaster/poky/
+      $ ./bitbake/lib/toaster/manage.py migrate
+      $ TOASTER_DIR=`pwd\` TEMPLATECONF='poky' \
+         ./bitbake/lib/toaster/manage.py checksettings
+      $ ./bitbake/lib/toaster/manage.py collectstatic
+
+
+    In the previous
+    example, from the ``poky`` directory, the ``migrate`` command
+    ensures the database schema changes have propagated correctly (i.e.
+    migrations). The next line sets the Toaster root directory
+    ``TOASTER_DIR`` and the location of the Toaster configuration file
+    ``TOASTER_CONF``, which is relative to ``TOASTER_DIR``. The
+    ``TEMPLATECONF`` value reflects the contents of
+    ``poky/.templateconf``, and by default, should include the string
+    "poky". For more information on the Toaster configuration file, see
+    the ":ref:`toaster-manual/toaster-manual-reference:Configuring Toaster`" section.
+
+    This line also runs the ``checksettings`` command, which configures
+    the location of the Toaster :term:`Build Directory`.
+    The Toaster
+    root directory ``TOASTER_DIR`` determines where the Toaster build
+    directory is created on the file system. In the example above,
+    ``TOASTER_DIR`` is set as follows::
+
+       /var/www/toaster/poky
+
+
+    This setting causes the Toaster build directory to be::
+
+       /var/www/toaster/poky/build
+
+    Finally, the ``collectstatic`` command is a Django framework command
+    that collects all the statically served files into a designated
+    directory to be served up by the Apache web server as defined by
+    ``STATIC_ROOT``.
+
+#.  Test and/or use the Mysql integration with Toaster's Django web
+    server. At this point, you can start up the normal Toaster Django
+    web server with the Toaster database in Mysql. You can use this web
+    server to confirm that the database migration and data population
+    from the Layer Index is complete.
+
+    To start the default Toaster Django web server with the Toaster
+    database now in Mysql, use the standard start commands::
+
+      $ source oe-init-build-env
+      $ source toaster start
+
+    Additionally, if Django is sufficient for your requirements, you can use
+    it for your release system and migrate later to Apache as your
+    requirements change.
+
+#.  Add an Apache configuration file for Toaster to your Apache web
+    server's configuration directory. If you are using Ubuntu or Debian,
+    put the file here::
+
+      /etc/apache2/conf-available/toaster.conf
+
+
+    If you are using Fedora or RedHat, put it here::
+
+      /etc/httpd/conf.d/toaster.conf
+
+    If you are using OpenSUSE, put it here::
+
+      /etc/apache2/conf.d/toaster.conf
+
+    Following is a sample Apache configuration for Toaster you can follow:
+
+    .. code-block:: apache
+
+      Alias /static /var/www/toaster/static_files
+      <Directory /var/www/toaster/static_files>
+         <IfModule mod_access_compat.c>
+            Order allow,deny
+            Allow from all
+         </IfModule>
+         <IfModule !mod_access_compat.c>
+            Require all granted
+         </IfModule>
+      </Directory>
+    
+      <Directory /var/www/toaster/poky/bitbake/lib/toaster/toastermain>
+         <Files "wsgi.py">
+            Require all granted
+         </Files>
+      </Directory>
+    
+      WSGIDaemonProcess toaster_wsgi python-path=/var/www/toaster/poky/bitbake/lib/toaster:/var/www/toaster/.local/lib/python3.4/site-packages
+      WSGIScriptAlias / "/var/www/toaster/poky/bitbake/lib/toaster/toastermain/wsgi.py"
+      <Location />
+         WSGIProcessGroup toaster_wsgi
+      </Location>
+
+
+    If you are using Ubuntu or Debian, you will need to enable the config and
+    module for Apache::
+
+      $ sudo a2enmod wsgi
+      $ sudo a2enconf toaster
+      $ chmod +x bitbake/lib/toaster/toastermain/wsgi.py
+
+    Finally, restart Apache to make sure all new configuration is loaded. For Ubuntu,
+    Debian, and OpenSUSE use::
+
+      $ sudo service apache2 restart
+
+    For Fedora and RedHat use::
+
+      $ sudo service httpd restart
+
+#.  Prepare the systemd service to run Toaster builds. Here is a sample
+    configuration file for the service:
+
+    .. code-block:: ini
+
+      [Unit]
+      Description=Toaster runbuilds
+      
+      [Service]
+      Type=forking User=toaster
+      ExecStart=/usr/bin/screen -d -m -S runbuilds /var/www/toaster/poky/bitbake/lib/toaster/runbuilds-service.sh start
+      ExecStop=/usr/bin/screen -S runbuilds -X quit
+      WorkingDirectory=/var/www/toaster/poky
+      
+      [Install]
+      WantedBy=multi-user.target
+
+
+    Prepare the ``runbuilds-service.sh`` script that you need to place in the
+    ``/var/www/toaster/poky/bitbake/lib/toaster/`` directory by setting
+    up executable permissions::
+
+      #!/bin/bash
+      
+      #export http_proxy=http://proxy.host.com:8080
+      #export https_proxy=http://proxy.host.com:8080
+      #export GIT_PROXY_COMMAND=$HOME/bin/gitproxy
+      cd ~/poky/
+      source ./oe-init-build-env build
+      source ../bitbake/bin/toaster $1 noweb
+      [ "$1" == 'start' ] && /bin/bash
+
+#.  Run the service::
+
+       $ sudo service runbuilds start
+
+    Since the service is running in a detached screen session, you can
+    attach to it using this command::
+
+       $ sudo su - toaster
+       $ screen -rS runbuilds
+
+    You can detach from the service again using "Ctrl-a" followed by "d" key
+    combination.
+
+You can now open up a browser and start using Toaster.
+
+Using the Toaster Web Interface
+===============================
+
+The Toaster web interface allows you to do the following:
+
+-  Browse published layers in the `OpenEmbedded Layer
+   Index <http://layers.openembedded.org>`__ that are available for your
+   selected version of the build system.
+
+-  Import your own layers for building.
+
+-  Add and remove layers from your configuration.
+
+-  Set configuration variables.
+
+-  Select a target or multiple targets to build.
+
+-  Start your builds.
+
+-  See what was built (recipes and packages) and what packages were
+   installed into your final image.
+
+-  Browse the directory structure of your image.
+
+-  See the value of all variables in your build configuration, and which
+   files set each value.
+
+-  Examine error, warning and trace messages to aid in debugging.
+
+-  See information about the BitBake tasks executed and reused during
+   your build, including those that used shared state.
+
+-  See dependency relationships between recipes, packages and tasks.
+
+-  See performance information such as build time, task time, CPU usage,
+   and disk I/O.
+
+.. _web-interface-videos:
+
+Toaster Web Interface Videos
+----------------------------
+
+Following are several videos that show how to use the Toaster GUI:
+
+-  *Build Configuration:* This
+   `video <https://www.youtube.com/watch?v=qYgDZ8YzV6w>`__ overviews and
+   demonstrates build configuration for Toaster.
+
+-  *Build Custom Layers:* This
+   `video <https://www.youtube.com/watch?v=QJzaE_XjX5c>`__ shows you how
+   to build custom layers that are used with Toaster.
+
+-  *Toaster Homepage and Table Controls:* This
+   `video <https://www.youtube.com/watch?v=QEARDnrR1Xw>`__ goes over the
+   Toaster entry page, and provides an overview of the data manipulation
+   capabilities of Toaster, which include search, sorting and filtering
+   by different criteria.
+
+-  *Build Dashboard:* This
+   `video <https://www.youtube.com/watch?v=KKqHYcnp2gE>`__ shows you the
+   build dashboard, a page providing an overview of the information
+   available for a selected build.
+
+-  *Image Information:* This
+   `video <https://www.youtube.com/watch?v=XqYGFsmA0Rw>`__ walks through
+   the information Toaster provides about images: packages installed and
+   root file system.
+
+-  *Configuration:* This
+   `video <https://www.youtube.com/watch?v=UW-j-T2TzIg>`__ provides
+   Toaster build configuration information.
+
+-  *Tasks:* This `video <https://www.youtube.com/watch?v=D4-9vGSxQtw>`__
+   shows the information Toaster provides about the tasks run by the
+   build system.
+
+-  *Recipes and Packages Built:* This
+   `video <https://www.youtube.com/watch?v=x-6dx4huNnw>`__ shows the
+   information Toaster provides about recipes and packages built.
+
+-  *Performance Data:* This
+   `video <https://www.youtube.com/watch?v=qWGMrJoqusQ>`__ shows the
+   build performance data provided by Toaster.
+
+.. _a-note-on-the-local-yocto-project-release:
+
+Additional Information About the Local Yocto Project Release
+------------------------------------------------------------
+
+This section only applies if you have set up Toaster for local
+development, as explained in the
+":ref:`toaster-manual/toaster-manual-setup-and-use:starting toaster for local development`"
+section.
+
+When you create a project in Toaster, you will be asked to provide a
+name and to select a Yocto Project release. One of the release options
+you will find is called "Local Yocto Project".
+
+.. image:: figures/new-project.png
+   :align: center
+   :scale: 75%
+
+When you select the "Local Yocto Project" release, Toaster will run your
+builds using the local Yocto Project clone you have in your computer:
+the same clone you are using to run Toaster. Unless you manually update
+this clone, your builds will always use the same Git revision.
+
+If you select any of the other release options, Toaster will fetch the
+tip of your selected release from the upstream `Yocto Project
+repository <https://git.yoctoproject.org>`__ every time you run a build.
+Fetching this tip effectively means that if your selected release is
+updated upstream, the Git revision you are using for your builds will
+change. If you are doing development locally, you might not want this
+change to happen. In that case, the "Local Yocto Project" release might
+be the right choice.
+
+However, the "Local Yocto Project" release will not provide you with any
+compatible layers, other than the three core layers that come with the
+Yocto Project:
+
+-  `openembedded-core <http://layers.openembedded.org/layerindex/branch/master/layer/openembedded-core/>`__
+
+-  `meta-poky <http://layers.openembedded.org/layerindex/branch/master/layer/meta-poky/>`__
+
+-  `meta-yocto-bsp <http://layers.openembedded.org/layerindex/branch/master/layer/meta-yocto-bsp/>`__
+
+.. image:: figures/compatible-layers.png
+   :align: center
+   :scale: 75%
+
+If you want to build any other layers, you will need to manually import
+them into your Toaster project, using the "Import layer" page.
+
+.. image:: figures/import-layer.png
+   :align: center
+   :scale: 75%
+
+.. _toaster-web-interface-preferred-version:
+
+Building a Specific Recipe Given Multiple Versions
+--------------------------------------------------
+
+Occasionally, a layer might provide more than one version of the same
+recipe. For example, the ``openembedded-core`` layer provides two
+versions of the ``bash`` recipe (i.e. 3.2.48 and 4.3.30-r0) and two
+versions of the ``which`` recipe (i.e. 2.21 and 2.18). The following
+figure shows this exact scenario:
+
+.. image:: figures/bash-oecore.png
+   :align: center
+   :scale: 75%
+
+By default, the OpenEmbedded build system builds one of the two recipes.
+For the ``bash`` case, version 4.3.30-r0 is built by default.
+Unfortunately, Toaster as it exists, is not able to override the default
+recipe version. If you would like to build bash 3.2.48, you need to set
+the
+:term:`PREFERRED_VERSION`
+variable. You can do so from Toaster, using the "Add variable" form,
+which is available in the "BitBake variables" page of the project
+configuration section as shown in the following screen:
+
+.. image:: figures/add-variable.png
+   :align: center
+   :scale: 75%
+
+To specify ``bash`` 3.2.48 as the version to build, enter
+"PREFERRED_VERSION_bash" in the "Variable" field, and "3.2.48" in the
+"Value" field. Next, click the "Add variable" button:
+
+.. image:: figures/set-variable.png
+   :align: center
+   :scale: 75%
+
+After clicking the "Add variable" button, the settings for
+``PREFERRED_VERSION`` are added to the bottom of the BitBake variables
+list. With these settings, the OpenEmbedded build system builds the
+desired version of the recipe rather than the default version:
+
+.. image:: figures/variable-added.png
+   :align: center
+   :scale: 75%
diff --git a/poky/documentation/toaster-manual/toaster-manual-setup-and-use.xml b/poky/documentation/toaster-manual/toaster-manual-setup-and-use.xml
index d810b9d..f555745 100644
--- a/poky/documentation/toaster-manual/toaster-manual-setup-and-use.xml
+++ b/poky/documentation/toaster-manual/toaster-manual-setup-and-use.xml
@@ -70,17 +70,17 @@
             web server. This is useful for the following:
             <itemizedlist>
                 <listitem><para>
-                    Capturing a command-line build’s statistics into
+                    Capturing a command-line build's statistics into
                     the Toaster database for examination later.
                     </para></listitem>
                 <listitem><para>
-                    Capturing a command-line build’s statistics when
+                    Capturing a command-line build's statistics when
                     the Toaster server is already running.
                     </para></listitem>
                 <listitem><para>
                     Having one instance of the Toaster web server
                     track and capture multiple command-line builds,
-                    where each build is started in its own “noweb”
+                    where each build is started in its own "noweb"
                     Toaster environment.
                     </para></listitem>
             </itemizedlist>
@@ -92,7 +92,7 @@
             minutes to ensure the complete transfer of its BitBake build
             statistics to the Toaster database.
             If you have a separate Toaster web server instance running, you
-            can watch this command-line build’s progress and examine the
+            can watch this command-line build's progress and examine the
             results as soon as they are posted:
             <literallayout class='monospaced'>
      $ source toaster start noweb
@@ -107,7 +107,7 @@
 
         <para>
             You can start a Toaster environment with the
-            “New Projects” feature disabled.
+            "New Projects" feature disabled.
             Doing so is useful for the following:
             <itemizedlist>
                 <listitem><para>
@@ -470,7 +470,7 @@
                       <filename>STATIC_ROOT</filename>.
                       </para></listitem>
                   <listitem><para>
-                      Test and/or use the Mysql integration with Toaster’s
+                      Test and/or use the Mysql integration with Toaster's
                       Django web server.
                       At this point, you can start up the normal Toaster
                       Django web server with the Toaster database in Mysql.
diff --git a/poky/documentation/toaster-manual/toaster-manual-start.rst b/poky/documentation/toaster-manual/toaster-manual-start.rst
new file mode 100644
index 0000000..2d612b8
--- /dev/null
+++ b/poky/documentation/toaster-manual/toaster-manual-start.rst
@@ -0,0 +1,57 @@
+.. SPDX-License-Identifier: CC-BY-2.0-UK
+.. Set default pygments highlighting to shell for this document
+.. highlight:: shell
+
+************************
+Preparing to Use Toaster
+************************
+
+This chapter describes how you need to prepare your system in order to
+use Toaster.
+
+.. _toaster-setting-up-the-basic-system-requirements:
+
+Setting Up the Basic System Requirements
+========================================
+
+Before you can use Toaster, you need to first set up your build system
+to run the Yocto Project. To do this, follow the instructions in the
+":ref:`dev-manual/dev-manual-start:preparing the build host`" section of
+the Yocto Project Development Tasks Manual. For Ubuntu/Debian, you might
+also need to do an additional install of pip3. ::
+
+   $ sudo apt-get install python3-pip
+
+.. _toaster-establishing-toaster-system-dependencies:
+
+Establishing Toaster System Dependencies
+========================================
+
+Toaster requires extra Python dependencies in order to run. A Toaster
+requirements file named ``toaster-requirements.txt`` defines the Python
+dependencies. The requirements file is located in the ``bitbake``
+directory, which is located in the root directory of the
+:term:`Source Directory` (e.g.
+``poky/bitbake/toaster-requirements.txt``). The dependencies appear in a
+``pip``, install-compatible format.
+
+.. _toaster-load-packages:
+
+Install Toaster Packages
+------------------------
+
+You need to install the packages that Toaster requires. Use this
+command::
+
+   $ pip3 install --user -r bitbake/toaster-requirements.txt
+
+The previous command installs the necessary Toaster modules into a local
+python 3 cache in your ``$HOME`` directory. The caches is actually
+located in ``$HOME/.local``. To see what packages have been installed
+into your ``$HOME`` directory, do the following::
+
+   $ pip3 list installed --local
+
+If you need to remove something, the following works::
+
+   $ pip3 uninstall PackageNameToUninstall
diff --git a/poky/documentation/toaster-manual/toaster-manual.rst b/poky/documentation/toaster-manual/toaster-manual.rst
new file mode 100644
index 0000000..f6f5941
--- /dev/null
+++ b/poky/documentation/toaster-manual/toaster-manual.rst
@@ -0,0 +1,19 @@
+.. SPDX-License-Identifier: CC-BY-2.0-UK
+
+===================
+Toaster User Manual
+===================
+
+|
+
+.. toctree::
+   :caption: Table of Contents
+   :numbered:
+
+   toaster-manual-intro
+   toaster-manual-start
+   toaster-manual-setup-and-use
+   toaster-manual-reference
+   history
+
+.. include:: /boilerplate.rst