diff --git a/xml/p10/node_occ_fir.xml b/xml/p10/node_occ_fir.xml
index 769f09a..0e6df35 100644
--- a/xml/p10/node_occ_fir.xml
+++ b/xml/p10/node_occ_fir.xml
@@ -5,10 +5,20 @@
         <action attn_type="CS" config="00"/>
         <action attn_type="RE" config="01"/>
     </local_fir>
-    <bit pos="0">Input tied to 0.  Used by OCC Firmware to produce an attention to the FSP.</bit>
-    <bit pos="1">Input tied to 0.  Used by OCC Firmware to produce an attention tothe FSP.</bit>
-    <bit pos="2">Input tied to 0. Used by STOP GPE code to indicated to HYP that a QME has indicated a fault.</bit>
-    <bit pos="3">Input tied to 0.   Written by stop recovery firmware to indicate that the host side actions are complete and that FFDC information is available for</bit>
+    <register name="OCC_SCOM_ERR_RPT">
+        <instance addr="0x0101080A" reg_inst="0"/>
+    </register>
+    <register name="OCC_SCOM_ERR_RPT2">
+        <instance addr="0x0101080B" reg_inst="0"/>
+    </register>
+    <capture_group node_inst="0">
+        <capture_register reg_inst="0" reg_name="OCC_SCOM_ERR_RPT" />
+        <capture_register reg_inst="0" reg_name="OCC_SCOM_ERR_RPT2" />
+    </capture_group>
+    <bit pos="0">OCC_FW0</bit>
+    <bit pos="1">OCC_FW1</bit>
+    <bit pos="2">OCC_QME_ERROR_NOTIFY</bit>
+    <bit pos="3">reserved</bit>
     <bit pos="4">OCC Heartbeat Error</bit>
     <bit pos="5">GPE0 asserted a watchdog timeout condition</bit>
     <bit pos="6">GPE1 asserted a watchdog timeout condition</bit>
@@ -18,9 +28,9 @@
     <bit pos="10">GPE1 asserted an error condition that caused it to halt.</bit>
     <bit pos="11">GPE2 asserted an error condition that caused it to halt.</bit>
     <bit pos="12">GPE3 asserted an error condition that caused it to halt.</bit>
-    <bit pos="13">OCB Error (recoverable error)</bit>
-    <bit pos="14">SRAM Uncorrectable Error (recoverable error)</bit>
-    <bit pos="15">SRAM Correctable Error (masked (product); recoverable error (mfg)</bit>
+    <bit pos="13">OCB Error to PM Hcode for PM Complex Restart</bit>
+    <bit pos="14">SRAM UE to PM Hcode for PM Complex Restart</bit>
+    <bit pos="15">SRAM CE</bit>
     <bit pos="16">GPE0 asserted a halt condition</bit>
     <bit pos="17">GPE1 asserted a halt condition</bit>
     <bit pos="18">GPE2 asserted a halt condition</bit>
@@ -29,42 +39,42 @@
     <bit pos="21">GPE1 attempted to write outside the region defined in GPESWPR</bit>
     <bit pos="22">GPE2 attempted to write outside the region defined in GPESWPR</bit>
     <bit pos="23">GPE3 attempted to write outside the region defined in GPESWPR</bit>
-    <bit pos="24">Implemented but not used, inputs tied to 0</bit>
-    <bit pos="25">Implemented but not used, inputs tied to 0</bit>
-    <bit pos="26">External Trigger pin active (recoverable (product)</bit>
-    <bit pos="27">PPC405 Core Reset Output asserted (??? firmware)</bit>
-    <bit pos="28">PPC405 Chip Reset Output asserted (??? firmware)</bit>
-    <bit pos="29">PPC405 System Reset Output asserted (??? firmware)</bit>
-    <bit pos="30">PPC405 Wait State asserted (??? firmware)</bit>
-    <bit pos="31">PPC405 Stop Ack output asserted (recoverable -&gt; logging)</bit>
-    <bit pos="32">OCB Direct Bridge Error - See OCCERRRPT2[8:11] for error source</bit>
-    <bit pos="33">OCB PIB Address Parity Error - (PIB read or write operation).  Note:  may be set for either direct bridge or indirect channel operations.</bit>
+    <bit pos="24">Safe Mode for debug use</bit>
+    <bit pos="25">reserved</bit>
+    <bit pos="26">EXTERNAL_TRAP</bit>
+    <bit pos="27">PPC405 Core Reset Output asserted (OCC firmware)</bit>
+    <bit pos="28">PPC405 Chip Reset Output asserted (OCC firmware)</bit>
+    <bit pos="29">PPC405 System Reset Output asserted (OCC firmware)</bit>
+    <bit pos="30">PPC405 Wait State asserted (OCC firmware)</bit>
+    <bit pos="31">PPC405 Stop Ack output asserted</bit>
+    <bit pos="32">OCB Direct Bridge Error</bit>
+    <bit pos="33">OCB PIB Address Parity Error</bit>
     <bit pos="34">Indirect Channel Error</bit>
-    <bit pos="35">Parity error detected on OPIT interrupt bus. Interrupts are hung.</bit>
-    <bit pos="36">OPIT interrupt state machine error occurred.</bit>
-    <bit pos="37">Implemented but not used.  Input tied to 0</bit>
-    <bit pos="38">Implemented but not used.  Input tied to 0</bit>
-    <bit pos="39">Implemented but not used.  Input tied to 0</bit>
-    <bit pos="40">Implemented but not used.  Input tied to 0</bit>
-    <bit pos="41">Implemented but not used.  Input tied to 0</bit>
+    <bit pos="35">Parity error detected on OPIT interrupt bus</bit>
+    <bit pos="36">OPIT interrupt state machine error occurred</bit>
+    <bit pos="37">reserved</bit>
+    <bit pos="38">reserved</bit>
+    <bit pos="39">reserved</bit>
+    <bit pos="40">reserved</bit>
+    <bit pos="41">reserved</bit>
     <bit pos="42">JTAG accelerator error</bit>
     <bit pos="43">Any OCI Slave error occurreds</bit>
     <bit pos="44">PPC405 cache UE</bit>
     <bit pos="45">PPC405 cache CE</bit>
     <bit pos="46">PPC405 Machine Check</bit>
-    <bit pos="47">SRAM spare direct error Summary.  See OCCERRRPT2[0:3] for details</bit>
-    <bit pos="48">SRAM Controller Error - A read, write, or parity error occurred in the  SRAM tank controller.   See OCCERRRPT2[12:18] for more information</bit>
-    <bit pos="49">Implemented but notused.   Input tied to 0</bit>
-    <bit pos="50">Implemented but notused.   Input tied to 0</bit>
-    <bit pos="51">OCI slave error for GPE0 (see OCCERRPT for details)</bit>
-    <bit pos="52">OCI slave error for GPE1 (see OCCERRPT for details)</bit>
-    <bit pos="53">OCI slave error for GPE2 (see OCCERRPT for details)</bit>
-    <bit pos="54">OCI slave error for GPE3 (see OCCERRPT for details)</bit>
-    <bit pos="55">PPC405 ICU timeout on OCI  request</bit>
-    <bit pos="56">PPC405 DCU timeout on OCI  request</bit>
-    <bit pos="57">Used by OCC to indicate that a fault occurred (to achieve safe mode).  Connected to OCCMISC[firmware_fault].</bit>
-    <bit pos="58">Used by OCC to notify another firmware entity that an event occurred.  Connected to OCCMISC[firmware_notify].</bit>
-    <bit pos="59">Implemented but not used.  Inputs tied to 0.</bit>
-    <bit pos="60">Implemented but not used.  Inputs tied to 0.</bit>
-    <bit pos="61">Implemented but not used.  Inputs tied to 0.</bit>
+    <bit pos="47">SRAM spare direct error Summary</bit>
+    <bit pos="48">Read, write, or parity error in the SRAM tank controller</bit>
+    <bit pos="49">reserved</bit>
+    <bit pos="50">reserved</bit>
+    <bit pos="51">OCI slave error for GPE0</bit>
+    <bit pos="52">OCI slave error for GPE1</bit>
+    <bit pos="53">OCI slave error for GPE2</bit>
+    <bit pos="54">OCI slave error for GPE3</bit>
+    <bit pos="55">PPC405 ICU timeout on OCI request</bit>
+    <bit pos="56">PPC405 DCU timeout on OCI request</bit>
+    <bit pos="57">OCC fault occurred (to achieve safe mode)</bit>
+    <bit pos="58">Read by HYP as part of the communication of a Power Management fault</bit>
+    <bit pos="59">reserved</bit>
+    <bit pos="60">reserved</bit>
+    <bit pos="61">reserved</bit>
 </attn_node>