diff --git a/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/conf/layer.conf b/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/conf/layer.conf
index b34e780..ac8a2a2 100644
--- a/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/conf/layer.conf
+++ b/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/conf/layer.conf
@@ -1,9 +1,5 @@
 # We have a conf and classes directory, add to BBPATH
 BBPATH .= ":${LAYERDIR}"
 
-# We have a recipes-* directories, add to BBFILES
-BBFILES += "${LAYERDIR}/recipes-*/*/*.bb \
-	${LAYERDIR}/recipes-*/*/*.bbappend"
-
 BBFILE_COLLECTIONS += "palmetto"
 BBFILE_PATTERN_palmetto = ""
diff --git a/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes-bsp/u-boot/files/config.patch b/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes-bsp/u-boot/files/config.patch
deleted file mode 100644
index c5216e7..0000000
--- a/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes-bsp/u-boot/files/config.patch
+++ /dev/null
@@ -1,14 +0,0 @@
---- a/include/configs/palmetto.h
-+++ b/include/configs/palmetto.h
-@@ -96,11 +96,8 @@
- #define CONFIG_UPDATE           "tftp 40800000 ast2400.scr; so 40800000'"
- 
- #define CONFIG_BOOTDELAY	3		/* autoboot after 3 seconds	*/
--#define CONFIG_AUTOBOOT_KEYED
- #define CONFIG_AUTOBOOT_PROMPT		\
- 	"autoboot in %d seconds (stop with 'Delete' key)...\n", bootdelay
--#define CONFIG_AUTOBOOT_STOP_STR	"\x1b\x5b\x33\x7e" /* 'Delete', ESC[3~ */
--#define CONFIG_ZERO_BOOTDELAY_CHECK
- 
- #ifdef CONFIG_FLASH_AST2300
- #define CONFIG_BOOTCOMMAND	"bootm 20080000 20300000"
diff --git a/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes-bsp/u-boot/files/fw_env.config b/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes-bsp/u-boot/files/fw_env.config
deleted file mode 100644
index 9cb3ad2..0000000
--- a/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes-bsp/u-boot/files/fw_env.config
+++ /dev/null
@@ -1,22 +0,0 @@
-# Configuration file for fw_(printenv/setenv) utility.
-# Up to two entries are valid, in this case the redundant
-# environment sector is assumed present.
-# Notice, that the "Number of sectors" is ignored on NOR and SPI-dataflash.
-# Futhermore, if the Flash sector size is ommitted, this value is assumed to
-# be the same as the Environment size, which is valid for NOR and SPI-dataflash
-
-# NOR example
-# MTD device name	Device offset	Env. size	Flash sector size	Number of sectors
-/dev/mtd1		0x0000		0x20000		0x20000
-#/dev/mtd2		0x0000		0x4000		0x4000
-
-# MTD SPI-dataflash example
-# MTD device name	Device offset	Env. size	Flash sector size	Number of sectors
-#/dev/mtd5		0x4200		0x4200
-#/dev/mtd6		0x4200		0x4200
-
-# NAND example
-#/dev/mtd0		0x4000		0x4000		0x20000			2
-
-# Block device example
-#/dev/mmcblk0		0xc0000		0x20000
diff --git a/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes-bsp/u-boot/files/patch-2013.07/0000-u-boot-aspeed-064.patch b/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes-bsp/u-boot/files/patch-2013.07/0000-u-boot-aspeed-064.patch
deleted file mode 100644
index 7d8c805..0000000
--- a/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes-bsp/u-boot/files/patch-2013.07/0000-u-boot-aspeed-064.patch
+++ /dev/null
Binary files differ
diff --git a/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes-bsp/u-boot/files/patch-2013.07/0001-u-boot-openbmc.patch b/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes-bsp/u-boot/files/patch-2013.07/0001-u-boot-openbmc.patch
deleted file mode 100644
index 1c1c5ea..0000000
--- a/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes-bsp/u-boot/files/patch-2013.07/0001-u-boot-openbmc.patch
+++ /dev/null
@@ -1,1937 +0,0 @@
-diff --git a/arch/arm/cpu/arm926ejs/aspeed/IO.c b/arch/arm/cpu/arm926ejs/aspeed/IO.c
-index 86e9918..b06fdba 100644
---- a/arch/arm/cpu/arm926ejs/aspeed/IO.c
-+++ b/arch/arm/cpu/arm926ejs/aspeed/IO.c
-@@ -31,7 +31,7 @@ static const char ThisFile[] = "IO.c";
-   #include <post.h>
-   #include <malloc.h>
-   #include <net.h>
--  #include <COMMINF.H>
-+  #include "COMMINF.H"
- #endif
- #ifdef SLT_DOS
-   #include <stdlib.h>
-@@ -353,4 +353,3 @@ ULONG ReadSOC_DD(ULONG addr)
- #endif
-     return 0;
- }
--
-diff --git a/arch/arm/cpu/arm926ejs/aspeed/LAN9303.c b/arch/arm/cpu/arm926ejs/aspeed/LAN9303.c
-index 498d4fd..fdabd45 100644
---- a/arch/arm/cpu/arm926ejs/aspeed/LAN9303.c
-+++ b/arch/arm/cpu/arm926ejs/aspeed/LAN9303.c
-@@ -13,9 +13,9 @@ static const char ThisFile[] = "LAN9303.c";
- 
- #include "SWFUNC.H"
- #ifdef SLT_UBOOT
--  #include <COMMINF.H>
--  #include <MAC.H>
--  #include <IO.H>
-+  #include "COMMINF.H"
-+  #include "MAC.H"
-+  #include "IO.H"
- #endif
- 
- #ifdef SLT_DOS
-diff --git a/arch/arm/cpu/arm926ejs/aspeed/MAC.c b/arch/arm/cpu/arm926ejs/aspeed/MAC.c
-index 829da92..b4182f5 100644
---- a/arch/arm/cpu/arm926ejs/aspeed/MAC.c
-+++ b/arch/arm/cpu/arm926ejs/aspeed/MAC.c
-@@ -16,7 +16,7 @@ static const char ThisFile[] = "MAC.c";
- #ifdef SLT_UBOOT
-   #include <common.h>
-   #include <command.h>
--  #include <COMMINF.H>
-+  #include "COMMINF.H"
-   #include "STDUBOOT.H"
- #endif
- #ifdef SLT_DOS
-@@ -2081,5 +2081,3 @@ char TestingLoop (ULONG loop_checknum) {
- 	
- 	return(0);
- } // End char TestingLoop (ULONG loop_checknum)
--
--
-diff --git a/arch/arm/cpu/arm926ejs/aspeed/Makefile b/arch/arm/cpu/arm926ejs/aspeed/Makefile
-index 378745e..4c4e239 100644
---- a/arch/arm/cpu/arm926ejs/aspeed/Makefile
-+++ b/arch/arm/cpu/arm926ejs/aspeed/Makefile
-@@ -16,7 +16,7 @@
- 
- include $(TOPDIR)/config.mk
- 
--LIB	= $(obj)lib$(SOC).a
-+LIB	= $(obj)lib$(SOC).o
- 
- COBJS	= timer.o
- COBJS	+= reset.o
-@@ -41,7 +41,7 @@ START	:= $(addprefix $(obj),$(START))
- all:	$(obj).depend $(LIB)
- 
- $(LIB):	$(OBJS)
--	$(AR) $(ARFLAGS) $@ $(OBJS)
-+	$(call cmd_link_o_target, $(OBJS))
- 
- #########################################################################
- 
-diff --git a/arch/arm/cpu/arm926ejs/aspeed/NCSI.c b/arch/arm/cpu/arm926ejs/aspeed/NCSI.c
-index 7de06c3..7e86fb6 100644
---- a/arch/arm/cpu/arm926ejs/aspeed/NCSI.c
-+++ b/arch/arm/cpu/arm926ejs/aspeed/NCSI.c
-@@ -16,9 +16,9 @@ static const char ThisFile[] = "NCSI.c";
- #ifdef SLT_UBOOT
-   #include <common.h>
-   #include <command.h>
--  #include <COMMINF.H>
--  #include <NCSI.H>
--  #include <IO.H>
-+  #include "COMMINF.H"
-+  #include "NCSI.H"
-+  #include "IO.H"
- #endif
- #ifdef SLT_DOS
-   #include <stdio.h>
-diff --git a/arch/arm/cpu/arm926ejs/aspeed/PHY.c b/arch/arm/cpu/arm926ejs/aspeed/PHY.c
-index 6afed9d..db73a70 100644
---- a/arch/arm/cpu/arm926ejs/aspeed/PHY.c
-+++ b/arch/arm/cpu/arm926ejs/aspeed/PHY.c
-@@ -16,7 +16,7 @@ static const char ThisFile[] = "PHY.c";
- #ifdef SLT_UBOOT
-   #include <common.h>
-   #include <command.h>
--  #include <COMMINF.H>
-+  #include "COMMINF.H"
-   #include "STDUBOOT.H"
- #endif
- #ifdef SLT_DOS
-diff --git a/arch/arm/cpu/arm926ejs/aspeed/PLLTESTU.c b/arch/arm/cpu/arm926ejs/aspeed/PLLTESTU.c
-index 95958b0..2414d57 100644
---- a/arch/arm/cpu/arm926ejs/aspeed/PLLTESTU.c
-+++ b/arch/arm/cpu/arm926ejs/aspeed/PLLTESTU.c
-@@ -13,11 +13,11 @@ static const char ThisFile[] = "PLLTEST.c";
- 
- #include "SWFUNC.H"
- 
--#include <COMMINF.H>
--#include <STDUBOOT.H>
--#include <TYPEDEF.H>
--#include <IO.H>
--#include <PLLTESTU.H>
-+#include "COMMINF.H"
-+#include "STDUBOOT.H"
-+#include "TYPEDEF.H"
-+#include "IO.H"
-+#include "PLLTESTU.H"
- 
- /*
-  * static
-@@ -407,5 +407,3 @@ int pll_function(int argc, char *argv[])
-         return (ERR_FATAL);
-     }
- }
--
--
-diff --git a/arch/arm/cpu/arm926ejs/aspeed/STDUBOOT.H b/arch/arm/cpu/arm926ejs/aspeed/STDUBOOT.H
-index 7fbf590..4e0adf6 100644
---- a/arch/arm/cpu/arm926ejs/aspeed/STDUBOOT.H
-+++ b/arch/arm/cpu/arm926ejs/aspeed/STDUBOOT.H
-@@ -13,6 +13,5 @@
- 
- unsigned long int strtoul(char *string, char **endPtr, int base);
- int atoi( char s[] );
--int rand(void);
- 
- #endif // End STDUBOOT_H
-diff --git a/arch/arm/cpu/arm926ejs/aspeed/STDUBOOT.c b/arch/arm/cpu/arm926ejs/aspeed/STDUBOOT.c
-index 90e2997..4b1f439 100644
---- a/arch/arm/cpu/arm926ejs/aspeed/STDUBOOT.c
-+++ b/arch/arm/cpu/arm926ejs/aspeed/STDUBOOT.c
-@@ -19,11 +19,11 @@ int isspace ( char c )
- {
-     if ( ( c == ' ' ) || ( c == 9 ) || ( c == 13 ) )
-         return 1;
--    
-+
-     return 0;
- }
- 
--/* 
-+/*
-  * strtoul.c --
-  *
-  *  Source code for the "strtoul" library procedure.
-@@ -111,7 +111,7 @@ strtoul(char *string, char **endPtr, int base)
-      * If no base was provided, pick one from the leading characters
-      * of the string.
-      */
--    
-+
-     if (base == 0)
-     {
-     if (*p == '0') {
-@@ -219,17 +219,6 @@ int atoi( char s[] )
-         ans = ( 10 * ans ) + ( s[i] - '0' );
- 
-     return ans;
--} 
--
--// -----------------------------------------------------------------------------
--/* rand:return pseudo-random integer on 0...32767 */
--int rand(void)
--{
--    static unsigned long int next = 1;
--    
--    next = next * 1103515245 + 12345; 
--
--    return (unsigned int) ( next / 65536 ) % 32768;
- }
- 
- #endif // End SLT_UBOOT
-diff --git a/arch/arm/cpu/arm926ejs/aspeed/STRESS.c b/arch/arm/cpu/arm926ejs/aspeed/STRESS.c
-index dffd64f..e86685e 100644
---- a/arch/arm/cpu/arm926ejs/aspeed/STRESS.c
-+++ b/arch/arm/cpu/arm926ejs/aspeed/STRESS.c
-@@ -12,8 +12,8 @@
- static const char ThisFile[] = "STRESS.c";
- 
- #include "SWFUNC.H"
--#include <COMMINF.H>
--#include <IO.H>
-+#include "COMMINF.H"
-+#include "IO.H"
- 
- #define TIMEOUT_DRAM              5000000
- 
-@@ -142,4 +142,3 @@ int dram_stress_function(int argc, char *argv[])
-      
-      return( ret );
- }
--
-diff --git a/arch/arm/cpu/arm926ejs/aspeed/TRAPTEST.c b/arch/arm/cpu/arm926ejs/aspeed/TRAPTEST.c
-index 72936c0..24ec0c5 100644
---- a/arch/arm/cpu/arm926ejs/aspeed/TRAPTEST.c
-+++ b/arch/arm/cpu/arm926ejs/aspeed/TRAPTEST.c
-@@ -13,9 +13,9 @@ static const char ThisFile[] = "PLLTEST.c";
- 
- #include "SWFUNC.H"
- 
--#include <COMMINF.H>
--#include <TYPEDEF.H>
--#include <IO.H>
-+#include "COMMINF.H"
-+#include "TYPEDEF.H"
-+#include "IO.H"
- 
- #define ASTCHIP_2400    0
- #define ASTCHIP_2300    1
-diff --git a/arch/arm/cpu/arm926ejs/aspeed/mactest.c b/arch/arm/cpu/arm926ejs/aspeed/mactest.c
-index 95bd560..62a696d 100644
---- a/arch/arm/cpu/arm926ejs/aspeed/mactest.c
-+++ b/arch/arm/cpu/arm926ejs/aspeed/mactest.c
-@@ -19,9 +19,9 @@ static const char ThisFile[] = "MACTEST.c";
-   #include <post.h>
-   #include <malloc.h>
-   #include <net.h>
--  #include <COMMINF.H>
--  #include <STDUBOOT.H>
--  #include <IO.H>
-+  #include "COMMINF.H"
-+  #include "STDUBOOT.H"
-+  #include "IO.H"
- #else
-   #include <stdlib.h>
-   #include <string.h>
-@@ -1212,4 +1212,3 @@ Find_Err_IOMargin:;
-     return(Finish_Check(0));
-    
- }
--
-diff --git a/arch/arm/cpu/arm926ejs/aspeed/reset.c b/arch/arm/cpu/arm926ejs/aspeed/reset.c
-index e0a57f9..ce8dba1 100644
---- a/arch/arm/cpu/arm926ejs/aspeed/reset.c
-+++ b/arch/arm/cpu/arm926ejs/aspeed/reset.c
-@@ -17,7 +17,7 @@ void reset_cpu(ulong addr)
- {
- 	__raw_writel(0x10 , AST_WDT_BASE+0x04);
- 	__raw_writel(0x4755, AST_WDT_BASE+0x08);
--	__raw_writel(0x3, AST_WDT_BASE+0x0c);
-+	__raw_writel(0x23, AST_WDT_BASE+0x0c); /* reset the full chip */
- 
- 	while (1)
- 	/*nothing*/;
-diff --git a/arch/arm/cpu/arm926ejs/aspeed/timer.c b/arch/arm/cpu/arm926ejs/aspeed/timer.c
-index 4bba5c5..add4c0e 100644
---- a/arch/arm/cpu/arm926ejs/aspeed/timer.c
-+++ b/arch/arm/cpu/arm926ejs/aspeed/timer.c
-@@ -16,12 +16,17 @@
-  */
- 
- #include <common.h>
--#include <arm926ejs.h>
-+
-+#if CONFIG_ASPEED_TIMER_CLK < CONFIG_SYS_HZ
-+#error "CONFIG_ASPEED_TIMER_CLK must be as large as CONFIG_SYS_HZ"
-+#endif
- 
- #define TIMER_LOAD_VAL 0xffffffff
-+#define CLK_PER_HZ (CONFIG_ASPEED_TIMER_CLK / CONFIG_SYS_HZ)
- 
- /* macro to read the 32 bit timer */
--#define READ_TIMER (*(volatile ulong *)(CONFIG_SYS_TIMERBASE+0))
-+#define READ_CLK (*(volatile ulong *)(CONFIG_SYS_TIMERBASE + 0))
-+#define READ_TIMER (READ_CLK / CLK_PER_HZ)
- 
- static ulong timestamp;
- static ulong lastdec;
-@@ -57,27 +62,25 @@ void set_timer (ulong t)
- }
- 
- /* delay x useconds AND perserve advance timstamp value */
--void udelay (unsigned long usec)
-+void __udelay (unsigned long usec)
- {
--	ulong tmo, tmp;
--
--	if(usec >= 1000){		/* if "big" number, spread normalization to seconds */
--		tmo = usec / 1000;	/* start to normalize for usec to ticks per sec */
--		tmo *= CONFIG_SYS_HZ;		/* find number of "ticks" to wait to achieve target */
--		tmo /= 1000;		/* finish normalize. */
--	}else{				/* else small number, don't kill it prior to HZ multiply */
--		tmo = usec * CONFIG_SYS_HZ;
--		tmo /= (1000*1000);
--	}
--
--	tmp = get_timer (0);		/* get current timestamp */
--	if( (tmo + tmp + 1) < tmp )	/* if setting this fordward will roll time stamp */
--		reset_timer_masked ();	/* reset "advancing" timestamp to 0, set lastdec value */
--	else
--		tmo += tmp;		/* else, set advancing stamp wake up time */
--
--	while (get_timer_masked () < tmo)/* loop till event */
--		/*NOP*/;
-+  ulong last = READ_CLK;
-+  ulong clks;
-+  ulong elapsed = 0;
-+
-+  /* translate usec to clocks */
-+  clks = (usec / 1000) * CLK_PER_HZ;
-+  clks += (usec % 1000) * CLK_PER_HZ / 1000;
-+
-+  while (clks > elapsed) {
-+    ulong now = READ_CLK;
-+    if (now <= last) {
-+      elapsed += last - now;
-+    } else {
-+      elapsed += TIMER_LOAD_VAL - (now - last);
-+    }
-+    last = now;
-+  }
- }
- 
- void reset_timer_masked (void)
-@@ -100,7 +103,7 @@ ulong get_timer_masked (void)
- 		 * (TLV-now) amount of time after passing though -1
- 		 * nts = new "advancing time stamp"...it could also roll and cause problems.
- 		 */
--		timestamp += lastdec + TIMER_LOAD_VAL - now;
-+		timestamp += lastdec + (TIMER_LOAD_VAL / CLK_PER_HZ) - now;
- 	}
- 	lastdec = now;
- 
-@@ -110,25 +113,7 @@ ulong get_timer_masked (void)
- /* waits specified delay value and resets timestamp */
- void udelay_masked (unsigned long usec)
- {
--	ulong tmo;
--	ulong endtime;
--	signed long diff;
--
--	if (usec >= 1000) {		/* if "big" number, spread normalization to seconds */
--		tmo = usec / 1000;	/* start to normalize for usec to ticks per sec */
--		tmo *= CONFIG_SYS_HZ;		/* find number of "ticks" to wait to achieve target */
--		tmo /= 1000;		/* finish normalize. */
--	} else {			/* else small number, don't kill it prior to HZ multiply */
--		tmo = usec * CONFIG_SYS_HZ;
--		tmo /= (1000*1000);
--	}
--
--	endtime = get_timer_masked () + tmo;
--
--	do {
--		ulong now = get_timer_masked ();
--		diff = endtime - now;
--	} while (diff >= 0);
-+  __udelay(usec);
- }
- 
- /*
-@@ -146,8 +131,5 @@ unsigned long long get_ticks(void)
-  */
- ulong get_tbclk (void)
- {
--	ulong tbclk;
--
--	tbclk = CONFIG_SYS_HZ;
--	return tbclk;
-+	return CONFIG_SYS_HZ;
- }
-diff --git a/board/aspeed/ast2400/Makefile b/board/aspeed/ast2400/Makefile
-index 1970ea1..fb77fc9 100644
---- a/board/aspeed/ast2400/Makefile
-+++ b/board/aspeed/ast2400/Makefile
-@@ -11,7 +11,7 @@
- 
- include $(TOPDIR)/config.mk
- 
--LIB	= $(obj)lib$(BOARD).a
-+LIB	= $(obj)lib$(BOARD).o
- 
- COBJS   := ast2400.o flash.o flash_spi.o pci.o crc32.o slt.o regtest.o vfun.o vhace.o crt.o videotest.o mactest.o hactest.o mictest.o
- 
-@@ -28,17 +28,13 @@ OBJS    := $(addprefix $(obj),$(COBJS))
- SOBJS   := $(addprefix $(obj),$(SOBJS))
- 
- $(LIB): $(obj).depend $(OBJS) $(SOBJS)
--	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
-+	$(call cmd_link_o_target, $(OBJS) $(SOBJS))
- 
--clean:
--	rm -f $(SOBJS) $(OBJS)
--
--distclean:	clean
--	rm -f $(LIB) core *.bak $(obj).depend
-+#########################################################################
- 
- # defines $(obj).depend target
- include $(SRCTREE)/rules.mk
- 
--sinclude .depend
-+sinclude $(obj).depend
- 
- #########################################################################
-diff --git a/board/aspeed/ast2400/ast2400.c b/board/aspeed/ast2400/ast2400.c
-index 65bccbe..55ed6b7 100644
---- a/board/aspeed/ast2400/ast2400.c
-+++ b/board/aspeed/ast2400/ast2400.c
-@@ -10,6 +10,7 @@
-  */
- 
- #include <common.h>
-+#include <asm/io.h>
- #include <command.h>
- #include <pci.h>
- 
-@@ -105,8 +106,8 @@ int dram_init (void)
- {
-     DECLARE_GLOBAL_DATA_PTR;
- 
--    gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
--    gd->bd->bi_dram[0].size  = PHYS_SDRAM_1_SIZE;
-+    /* dram_init must store complete ramsize in gd->ram_size */
-+    gd->ram_size = get_ram_size((void *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE);
- 
-     return 0;
- }
-@@ -190,6 +191,22 @@ int ast1070_calibration()
- 	return 0;
- }
- 
-+static void watchdog_init()
-+{
-+#ifdef CONFIG_ASPEED_ENABLE_WATCHDOG
-+#define AST_WDT_BASE 0x1e785000
-+#define AST_WDT_CLK (1*1000*1000) /* 1M clock source */
-+  u32 reload = AST_WDT_CLK * CONFIG_ASPEED_WATCHDOG_TIMEOUT;
-+  /* set the reload value */
-+  __raw_writel(reload, AST_WDT_BASE + 0x04);
-+  /* magic word to reload */
-+  __raw_writel(0x4755, AST_WDT_BASE + 0x08);
-+  /* start the watchdog with 1M clk src and reset whole chip */
-+  __raw_writel(0x33, AST_WDT_BASE + 0x0c);
-+  printf("Watchdog: %us\n", CONFIG_ASPEED_WATCHDOG_TIMEOUT);
-+#endif
-+}
-+
- int misc_init_r(void)
- {
-     unsigned int reg, reg1, revision, chip_id, lpc_plus;
-@@ -290,6 +307,8 @@ int misc_init_r(void)
-     if (getenv ("eeprom") == NULL) {
- 	setenv ("eeprom", "y");
-     }
-+
-+    watchdog_init();
- }
- 
- #ifdef	CONFIG_PCI
-@@ -302,3 +321,15 @@ void pci_init_board(void)
-     aspeed_init_pci(&hose);
- }
- #endif
-+
-+int board_eth_init(bd_t *bis)
-+{
-+  int ret = -1;
-+#if defined(CONFIG_ASPEEDNIC)
-+  ret = aspeednic_initialize(bis);
-+#else
-+  printf("No ETH, ");
-+#endif
-+
-+  return ret;
-+}
-diff --git a/board/aspeed/ast2400/config.mk b/board/aspeed/ast2400/config.mk
-index 24ca09b..eddc3bf 100755
---- a/board/aspeed/ast2400/config.mk
-+++ b/board/aspeed/ast2400/config.mk
-@@ -9,10 +9,5 @@
- # MA 02111-1307 USA
- #
- 
--# ROM version
--#TEXT_BASE = 0xBFC00000
--
--# RAM version
--TEXT_BASE = 0x40500000
--#TEXT_BASE = 0x00000000
--#TEXT_BASE = 0x00400000
-+# SPI flash is mapped to 0x00000000 initially
-+CONFIG_SYS_TEXT_BASE = 0x00000000
-diff --git a/board/aspeed/ast2400/flash_spi.c b/board/aspeed/ast2400/flash_spi.c
-index ad89254..339e531 100755
---- a/board/aspeed/ast2400/flash_spi.c
-+++ b/board/aspeed/ast2400/flash_spi.c
-@@ -23,7 +23,7 @@
-  */
- 
- /* The DEBUG define must be before common to enable debugging */
--/* #define DEBUG	*/
-+/* #define DEBUG */
- 
- #include <common.h>
- #include <asm/processor.h>
-@@ -68,6 +68,7 @@ flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];		/* FLASH chips info */
- /* Support Flash ID */
- #define STM25P64		0x172020
- #define STM25P128		0x182020
-+#define N25Q128			0x18ba20
- #define N25Q256			0x19ba20
- #define N25Q512			0x20ba20
- #define S25FL064A		0x160201
-@@ -581,7 +582,7 @@ static ulong flash_get_size (ulong base, int banknum)
-         ulID = ((ulong)ch[0]) | ((ulong)ch[1] << 8) | ((ulong)ch[2] << 16) ;        
-         info->flash_id = ulID;
-         
--        //printf("SPI Flash ID: %x \n", ulID);
-+        printf("SPI Flash ID: %x \n", ulID);
- 
-         /* init default */        
-         info->iomode = IOMODEx1;
-@@ -617,6 +618,19 @@ static ulong flash_get_size (ulong base, int banknum)
-             ReadClk  = 50;
-             break;
-             
-+        case N25Q128:
-+	    info->sector_count = 256;
-+	    info->size = 0x1000000;        	
-+            erase_region_size  = 0x10000;
-+            info->readcmd = 0x0b;            
-+            info->dualport = 0;
-+            info->dummybyte = 1;
-+            info->buffersize = 256;            
-+            WriteClk = 50;
-+            EraseClk = 20;
-+            ReadClk  = 50;
-+	    break;
-+
-         case N25Q256:
- 	    info->sector_count = 256;
- 	    info->size = 0x1000000;        	
-@@ -1051,8 +1065,7 @@ AST2300 A0 SPI can't run faster than 50Mhz
-             } /* JDEC */        
-         }
-         				
--        debug ("erase_region_count = %d erase_region_size = %d\n",
--		erase_region_count, erase_region_size);
-+        debug ("erase_region_size = %d\n", erase_region_size);
- 
- 	sector = base;			
- 	for (j = 0; j < info->sector_count; j++) {
-diff --git a/board/aspeed/ast2400/platform.S b/board/aspeed/ast2400/platform.S
-index 27e8f26..dd94da0 100644
---- a/board/aspeed/ast2400/platform.S
-+++ b/board/aspeed/ast2400/platform.S
-@@ -334,7 +334,11 @@ set_MPLL:
-     str r1, [r0]
- 
- /* Debug - UART console message */
--    ldr r0, =0x1e78400c
-+    ldr r0, =0x1e6e2080
-+    ldr r1, =0xFFFF0000                          @ enable UART3 and UART4
-+    str r1, [r0]
-+
-+    ldr r0, =CONFIG_ASPEED_COM_LCR
-     mov r1, #0x83
-     str r1, [r0]
- 
-@@ -342,28 +346,38 @@ set_MPLL:
-     ldr r2, [r0]
-     mov r2, r2, lsr #12
-     tst r2, #0x01
--    ldr r0, =0x1e784000
-+    ldr r0, =CONFIG_ASPEED_COM
-+#if CONFIG_BAUDRATE == 115200
-     moveq r1, #0x0D                              @ Baudrate 115200
-     movne r1, #0x01                              @ Baudrate 115200, div13
--#if defined(CONFIG_DRAM_UART_38400)
-+#endif
-+#if CONFIG_BAUDRATE == 57600
-+    moveq r1, #0x1A                              @ Baudrate 57600
-+    movne r1, #0x02                              @ Baudrate 57600, div13
-+#endif
-+#if CONFIG_BAUDRATE == 38400
-     moveq r1, #0x27                              @ Baudrate 38400
-     movne r1, #0x03                              @ Baudrate 38400 , div13
- #endif
-+#if CONFIG_BAUDRATE == 9600
-+    moveq r1, #0x9c                              @ Baudrate 9600
-+    movne r1, #0x0C                              @ Baudrate 9600 , div13
-+#endif
-     str r1, [r0]
- 
--    ldr r0, =0x1e784004
-+    ldr r0, =CONFIG_ASPEED_COM_IER
-     mov r1, #0x00
-     str r1, [r0]
- 
--    ldr r0, =0x1e78400c
-+    ldr r0, =CONFIG_ASPEED_COM_LCR
-     mov r1, #0x03
-     str r1, [r0]
- 
--    ldr r0, =0x1e784008
-+    ldr r0, =CONFIG_ASPEED_COM_IIR
-     mov r1, #0x07
-     str r1, [r0]
- 
--    ldr r0, =0x1e784000
-+    ldr r0, =CONFIG_ASPEED_COM
-     mov r1, #0x0D                                @ '\r'
-     str r1, [r0]
-     mov r1, #0x0A                                @ '\n'
-@@ -575,7 +589,7 @@ delay_2:
-  ******************************************************************************/
- ddr3_init:
- /* Debug - UART console message */
--    ldr r0, =0x1e784000
-+    ldr r0, =CONFIG_ASPEED_COM
-     mov r1, #0x33                                @ '3'
-     str r1, [r0]
-     mov r1, #0x0D                                @ '\r'
-@@ -764,7 +778,7 @@ delay3_4:
-  ******************************************************************************/
- ddr2_init:
- /* Debug - UART console message */
--    ldr r0, =0x1e784000
-+    ldr r0, =CONFIG_ASPEED_COM
-     mov r1, #0x32                                @ '2'
-     str r1, [r0]
-     mov r1, #0x0D                                @ '\r'
-@@ -1416,7 +1430,7 @@ init_sram_start3:
-  *****************************************************************************/
- CBR0_START:
- /* Debug - UART console message */
--    ldr r0, =0x1e784000
-+    ldr r0, =CONFIG_ASPEED_COM
-     mov r1, #0x43                                @ 'C'
-     str r1, [r0]
-     mov r1, #0x42                                @ 'B'
-@@ -1454,7 +1468,7 @@ cbr0_next_dqidly:
-     bgt   CBR0_END
- 
- /* Debug - UART console message */
--    ldr   r0, =0x1e784000
-+    ldr   r0, =CONFIG_ASPEED_COM
-     and   r1, r8, #0x07
-     add   r1, r1, #0x30                          @ '0-7'
-     str   r1, [r0]
-@@ -1776,7 +1790,7 @@ delay_5:
-  *****************************************************************************/
- CBR1_START:
- /* Debug - UART console message */
--    ldr r0, =0x1e784000
-+    ldr r0, =CONFIG_ASPEED_COM
-     mov r1, #0x0D                                @ '\r'
-     str r1, [r0]
-     mov r1, #0x0A                                @ '\n'
-@@ -2057,7 +2071,7 @@ cbr1_set_result_end:
- 
- CBR3_START:
- /* Debug - UART console message */
--    ldr r0, =0x1e784000
-+    ldr r0, =CONFIG_ASPEED_COM
-     mov r1, #0x33                                @ '3'
-     str r1, [r0]
- /* Debug - UART console message */
-@@ -2276,7 +2290,7 @@ CBR3_END:
-  *****************************************************************************/
- CBR4_START:
- /* Debug - UART console message */
--    ldr r0, =0x1e784000
-+    ldr r0, =CONFIG_ASPEED_COM
-     mov r1, #0x34                                @ '4'
-     str r1, [r0]
- /* Debug - UART console message */
-@@ -2556,7 +2570,7 @@ set_scratch:
-     str r1, [r0]
- 
- /* Debug - UART console message */
--    ldr r0, =0x1e784000
-+    ldr r0, =CONFIG_ASPEED_COM
-     mov r1, #0x44                                @ 'D'
-     str r1, [r0]
-     mov r1, #0x6F                                @ 'o'
-@@ -2724,11 +2738,13 @@ ECC_Init_Flag:
-     orr r1, r1, #0x08
-     str r1, [r0]
- 
-+#ifndef CONFIG_ASPEED_ENABLE_JTAG
-     ldr r0, =0x1e6e2004
-     ldr r1, [r0]
-     ldr r2, =0xFFBFFFFF                          @ Enable JTAG Master, solve ARM stucked by JTAG issue
-     and r1, r1, r2
-     str r1, [r0]
-+#endif
- 
-     ldr r0, =0x1e6e2048                          @ Set MAC interface delay timing
-     ldr r1, =0x2255
-diff --git a/board/aspeed/ast2400/u-boot.lds b/board/aspeed/ast2400/u-boot.lds
-deleted file mode 100755
-index ff0fe22..0000000
---- a/board/aspeed/ast2400/u-boot.lds
-+++ /dev/null
-@@ -1,56 +0,0 @@
--/*
-- * (C) Copyright 2004
-- * Wolfgang Denk, DENX Software Engineering, <wg@denx.de>
-- *
-- * See file CREDITS for list of people who contributed to this
-- * project.
-- *
-- * This program is free software; you can redistribute it and/or
-- * modify it under the terms of the GNU General Public License as
-- * published by the Free Software Foundation; either version 2 of
-- * the License, or (at your option) any later version.
-- *
-- * This program is distributed in the hope that it will be useful,
-- * but WITHOUT ANY WARRANTY; without even the implied warranty of
-- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
-- * GNU General Public License for more details.
-- *
-- * You should have received a copy of the GNU General Public License
-- * along with this program; if not, write to the Free Software
-- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-- * MA 02111-1307 USA
-- */
--
--OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
--/*OUTPUT_FORMAT("elf32-arm", "elf32-arm", "elf32-arm")*/
--OUTPUT_ARCH(arm)
--ENTRY(_start)
--SECTIONS
--{
--	. = 0x00000000;
--
--	. = ALIGN(4);
--	.text	   :
--	{
--	  cpu/arm926ejs/start.o	(.text)
--	  *(.text)
--	}
--
--	. = ALIGN(4);
--	.rodata : { *(.rodata) }
--
--	. = ALIGN(4);
--	.data : { *(.data) }
--
--	. = ALIGN(4);
--	.got : { *(.got) }
--
--	__u_boot_cmd_start = .;
--	.u_boot_cmd : { *(.u_boot_cmd) }
--	__u_boot_cmd_end = .;
--
--	. = ALIGN(4);
--	__bss_start = .;
--	.bss : { *(.bss) }
--	_end = .;
--}
-diff --git a/boards.cfg b/boards.cfg
-index 674896b..ce6bff1 100644
---- a/boards.cfg
-+++ b/boards.cfg
-@@ -72,7 +72,8 @@ mini2440                     arm         arm920t     mini2440            friendl
- VCMA9                        arm         arm920t     vcma9               mpl            s3c24x0
- smdk2410                     arm         arm920t     -                   samsung        s3c24x0
- omap1510inn                  arm         arm925t     -                   ti
--ast2400                      arm         arm926ejs   ast2400             aspeed         aspeed
-+wedge                        arm         arm926ejs   ast2400             aspeed         aspeed
-+palmetto                     arm         arm926ejs   ast2400             aspeed         aspeed
- integratorap_cm926ejs        arm         arm926ejs   integrator          armltd         -           integratorap:CM926EJ_S
- integratorcp_cm926ejs        arm         arm926ejs   integrator          armltd         -           integratorcp:CM924EJ_S
- aspenite                     arm         arm926ejs   -                   Marvell        armada100
-diff --git a/common/cmd_slt.c b/common/cmd_slt.c
-index 9763692..6296416 100644
---- a/common/cmd_slt.c
-+++ b/common/cmd_slt.c
-@@ -9,6 +9,7 @@
-  *  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
- 
-+#include <common.h>
- #include <command.h>
- 
- extern int pll_function(int argc, char *argv[]);
-diff --git a/common/env_common.c b/common/env_common.c
-index 906b41f..f5af537 100644
---- a/common/env_common.c
-+++ b/common/env_common.c
-@@ -203,6 +203,9 @@ void env_relocate(void)
- #else
- 		bootstage_error(BOOTSTAGE_ID_NET_CHECKSUM);
- 		set_default_env("!bad CRC");
-+#ifdef CONFIG_ASPEED_WRITE_DEFAULT_ENV
-+    saveenv();
-+#endif
- #endif
- 	} else {
- 		env_relocate_spec();
-diff --git a/common/image.c b/common/image.c
-index f5ad097..2fc071b 100644
---- a/common/image.c
-+++ b/common/image.c
-@@ -902,6 +902,11 @@ int boot_get_ramdisk(int argc, char * const argv[], bootm_headers_t *images,
- 			rd_data = image_get_data(rd_hdr);
- 			rd_len = image_get_data_size(rd_hdr);
- 			rd_load = image_get_load(rd_hdr);
-+#ifdef CONFIG_ASPEED
-+			/* Need to copy the initrd into RAM */
-+			memmove_wd((void *)rd_load, (void *)rd_data, rd_len, CHUNKSZ);
-+			rd_data = rd_load;
-+#endif
- 			break;
- #if defined(CONFIG_FIT)
- 		case IMAGE_FORMAT_FIT:
-diff --git a/drivers/net/aspeednic.c b/drivers/net/aspeednic.c
-index 6b1ce05..d75ef67 100644
---- a/drivers/net/aspeednic.c
-+++ b/drivers/net/aspeednic.c
-@@ -16,6 +16,7 @@
- #include <malloc.h>
- #include <net.h>
- #include <pci.h>
-+#include <linux/mii.h>
- 
- 
- /*
-@@ -53,7 +54,6 @@
- #define MAC1_MDC                 (1 << 30)
- #define MAC1_PHY_LINK            (1 << 0)
- #define MAC2_MDC_MDIO            (1 << 2)
--#define MAC1_PHY_LINK            (1 << 0)
- #define MAC2_PHY_LINK            (1 << 1)
- #else
- #define MAC2_MDC_MDIO            (1 << 20)
-@@ -69,6 +69,9 @@ unsigned int aspeednic_iobase[CONFIG_ASPEED_MAC_NUMBER] = {
-   0x1E660000, 0x1E680000};
- #endif
- 
-+/* PHY address */
-+static u8 g_phy_addr = 0;
-+
- #undef DEBUG_SROM
- #undef DEBUG_SROM2
- 
-@@ -249,6 +252,7 @@ struct de4x5_desc {
- #define PHYID_RTL8201EL     0x001cc810
- #define PHYID_RTL8211         0x001cc910
- #define PHYID_BCM54612E             0x03625E6A
-+#define PHYID_BCM54616S             0x03625D12
- 
- //NCSI define & structure
- //NC-SI Command Packet
-@@ -410,6 +414,12 @@ static void  aspeednic_halt(struct eth_device* dev);
- static void  set_mac_address (struct eth_device* dev, bd_t* bis);
- static void  phy_write_register (struct eth_device* dev, u8 PHY_Register, u8 PHY_Address, u16 PHY_Data);
- static u16   phy_read_register (struct eth_device* dev, u8 PHY_Register, u8 PHY_Address);
-+#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
-+static int faraday_mdio_read(const char *devname, uint8_t addr, uint8_t reg,
-+                             uint16_t *value);
-+static int faraday_mdio_write(const char *devname, uint8_t addr, uint8_t reg,
-+                              uint16_t value);
-+#endif
- static void  set_mac_control_register(struct eth_device* dev);
- 
- #if defined(CONFIG_E500)
-@@ -456,7 +466,7 @@ void NCSI_Struct_Initialize(void)
- 
- int aspeednic_initialize(bd_t *bis)
- {
--  int               card_number = 0;
-+  int               card_number = CONFIG_ASPEED_MAC_CONFIG - 1;
-   unsigned int    iobase, SCURegister;
-   struct eth_device*  dev;
- 
-@@ -538,7 +548,7 @@ int aspeednic_initialize(bd_t *bis)
- 
-   dev->iobase = iobase;
- 
--  if (CONFIG_MAC1_PHY_SETTING >= 1) {
-+  if (CONFIG_ASPEED_MAC_PHY_SETTING >= 1) {
- //NCSI Struct Initialize
-     NCSI_Struct_Initialize();
-   }
-@@ -556,20 +566,22 @@ int aspeednic_initialize(bd_t *bis)
-   dev->recv   = aspeednic_recv;
- 
-   /* Ensure we're not sleeping. */
--  if (CONFIG_MAC1_PHY_SETTING >= 1) {
-+  if (CONFIG_ASPEED_MAC_PHY_SETTING >= 1) {
-     udelay(2000000); //2.0 sec
-   }
-   else {
-     udelay(10 * 1000);
-   }
- 
--
-   dev->init(dev, bis);
- 
-   eth_register(dev);
- 
-+#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
-+  miiphy_register(dev->name, faraday_mdio_read, faraday_mdio_write);
-+#endif
- 
--  return card_number;
-+  return 1;
- }
- 
- void Calculate_Checksum(unsigned char *buffer_base, int Length)
-@@ -1114,11 +1126,37 @@ void Set_Link (struct eth_device* dev)
-   Retry = 0;
- }
- 
-+static void aspeednic_probe_phy(struct eth_device *dev)
-+{
-+  u8 phy_addr;
-+  u16 phy_id;
-+
-+  /* assume it as 0 */
-+  g_phy_addr = 0;
-+
-+  /* Check if the PHY is up to snuff..., max phy addr is 0x1f */
-+  for (phy_addr = 0; phy_addr <= 0x1f; phy_addr++) {
-+    phy_id = phy_read_register(dev, MII_PHYSID1, phy_addr);
-+    /*
-+     * When it is unable to found PHY,
-+     * the interface usually return 0xffff or 0x0000
-+     */
-+    if (phy_id != 0xffff && phy_id != 0x0) {
-+      g_phy_addr = phy_addr;
-+      break;
-+    }
-+  }
-+  printf("%s: PHY at 0x%02x\n", dev->name, phy_addr);
-+}
-+
- static int aspeednic_init(struct eth_device* dev, bd_t* bis)
- {
-   unsigned long i, Package_Found = 0, Channel_Found = 0, Re_Send = 0, Link_Status;
- 
-   RESET_DE4X5(dev);
-+
-+  aspeednic_probe_phy(dev);
-+
-   set_mac_address (dev, bis);
-   set_mac_control_register (dev);
- 
-@@ -1149,7 +1187,7 @@ static int aspeednic_init(struct eth_device* dev, bd_t* bis)
-   tx_new = 0;
-   rx_new = 0;
- 
--  if (CONFIG_MAC1_PHY_SETTING >= 1) {
-+  if (CONFIG_ASPEED_MAC_PHY_SETTING >= 1) {
- //NCSI Start
- //DeSelect Package/ Select Package
-     for (i = 0; i < 4; i++) {
-@@ -1313,58 +1351,23 @@ static void aspeednic_halt(struct eth_device* dev)
- 
- static void set_mac_address (struct eth_device* dev, bd_t* bis)
- {
--  unsigned char  mac_address[6]; // 6 bytes mac address
--  unsigned char  ethaddress[20]; // string for setenv function
--  char *s;
--  int i, env;                // env variable 0: eeprom, 1: environment parameters
--
--  s = getenv ("eeprom");
--  env = (s && (*s == 'y')) ? 0 : 1;
--
--  if (env == 0) {
--    env = 1;
--    eeprom_init ();
--    eeprom_read (0xA0, 0, mac_address, 6);
--
--    for (i = 0; i < 6; i++) {
--      if (mac_address[i] != 0xFF) {
--        env = 0;  //Suppose not all 0xFF is valid
--      }
--    }
-+  if (!eth_getenv_enetaddr_by_index("eth", 0, dev->enetaddr)) {
-+    eth_random_enetaddr(dev->enetaddr);
-   }
- 
--  if (env == 0) { // EEPROM
--    sprintf (ethaddress, "%02X:%02X:%02X:%02X:%02X:%02X", mac_address[0], mac_address[1], mac_address[2], mac_address[3], mac_address[4], mac_address[5]);
--    setenv ("ethaddr", ethaddress);
--    OUTL(dev, ((mac_address[2] << 24) | (mac_address[3] << 16) | (mac_address[4] << 8) | mac_address[5]), MAC_LADR_REG);
--    OUTL(dev, ((mac_address[0] << 8) | mac_address[1]), MAC_MADR_REG);
--    if (CONFIG_MAC1_PHY_SETTING >= 1) {
--      for (i = 0; i < 6; i++) {
--        NCSI_Request.SA[i] = mac_address[i];
--      }
--    }
--  }
--  else { // Environment Parameters
--    OUTL(dev, ((bis->bi_enetaddr[2] << 24) | (bis->bi_enetaddr[3] << 16) | (bis->bi_enetaddr[4] << 8) | bis->bi_enetaddr[5]), MAC_LADR_REG);
--    OUTL(dev, ((bis->bi_enetaddr[0] << 8) | bis->bi_enetaddr[1]), MAC_MADR_REG);
--    if (CONFIG_MAC1_PHY_SETTING >= 1) {
--      for (i = 0; i < 6; i++) {
--        NCSI_Request.SA[i] = bis->bi_enetaddr[i];
--      }
--    }
-+  OUTL(dev, ((dev->enetaddr[2] << 24) | (dev->enetaddr[3] << 16)
-+             | (dev->enetaddr[4] << 8) | dev->enetaddr[5]), MAC_LADR_REG);
-+  OUTL(dev, ((dev->enetaddr[0] << 8) | dev->enetaddr[1]), MAC_MADR_REG);
-+  if (CONFIG_ASPEED_MAC_PHY_SETTING >= 1) {
-+    memcpy(NCSI_Request.SA, dev->enetaddr, 6);
-   }
--
- }
- 
--
- static u16 phy_read_register (struct eth_device* dev, u8 PHY_Register, u8 PHY_Address)
- {
-   u32 Data, Status = 0, Loop_Count = 0, PHY_Ready = 1;
-   u16 Return_Data;
- 
--#ifdef  REALTEK_PHY_SUPPORT
--  PHY_Address = 0x01;
--#endif
- //20us * 100 = 2ms > (1 / 2.5Mhz) * 0x34
-   OUTL(dev, (PHY_Register << 21) + (PHY_Address << 16) + MIIRD + MDC_CYCTHR, PHYCR_REG);
-   do {
-@@ -1378,7 +1381,6 @@ static u16 phy_read_register (struct eth_device* dev, u8 PHY_Register, u8 PHY_Ad
-   } while (Status == MIIRD);
- 
-   if (PHY_Ready == 0) {
--    printf ("PHY NOT REDAY ");
-     return 0;
-   }
-   Data = INL (dev, PHYDATA_REG);
-@@ -1392,9 +1394,6 @@ static void phy_write_register (struct eth_device* dev, u8 PHY_Register, u8 PHY_
- {
-   u32 Status = 0, Loop_Count = 0, PHY_Ready = 1;
- 
--#ifdef  REALTEK_PHY_SUPPORT
--  PHY_Address = 0x01;
--#endif
- //20us * 100 = 2ms > (1 / 2.5Mhz) * 0x34
-   OUTL(dev, PHY_Data, PHYDATA_REG);
-   OUTL(dev, (PHY_Register << 21) + (PHY_Address << 16) + MIIWR + MDC_CYCTHR, PHYCR_REG);
-@@ -1407,31 +1406,66 @@ static void phy_write_register (struct eth_device* dev, u8 PHY_Register, u8 PHY_
-       break;
-     }
-   } while (Status == MIIWR);
--  if (PHY_Ready == 0) {
--    printf ("PHY NOT REDAY ");
-+}
-+
-+#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII)
-+
-+static int faraday_mdio_read(
-+  const char *devname, uint8_t addr, uint8_t reg, uint16_t *value)
-+{
-+  int ret = 0;
-+  struct eth_device *dev;
-+
-+  dev = eth_get_dev_by_name(devname);
-+  if (dev == NULL) {
-+    printf("%s: no such device\n", devname);
-+    ret = -1;
-+  } else {
-+    *value = phy_read_register(dev, reg, addr);
-+  }
-+
-+  return ret;
-+}
-+
-+static int faraday_mdio_write(
-+  const char *devname, uint8_t addr, uint8_t reg, uint16_t value)
-+{
-+  int ret = 0;
-+  struct eth_device *dev;
-+
-+  dev = eth_get_dev_by_name(devname);
-+  if (dev == NULL) {
-+    printf("%s: no such device\n", devname);
-+    ret = -1;
-+  } else {
-+    phy_write_register(dev, reg, addr, value);
-   }
-+
-+  return ret;
- }
- 
-+#endif    /* #if defined(CONFIG_MII) || defined(CONFIG_CMD_MII) */
-+
- static void set_mac_control_register (struct eth_device* dev)
- {
-   unsigned long MAC_CR_Register = 0;
--  unsigned long   Loop_Count = 0, PHY_Ready = 1, Chip_ID;
-+  unsigned int   Loop_Count = 0, PHY_Ready = 1, Chip_ID;
-   u16    PHY_Status, PHY_Speed, PHY_Duplex, Resolved_Status = 0, Advertise, Link_Partner;
- 
--  if (CONFIG_MAC1_PHY_SETTING >= 1) {
-+  if (CONFIG_ASPEED_MAC_PHY_SETTING >= 1) {
-     MAC_CR_Register = SPEED_100M_MODE_bit | RX_BROADPKT_bit | FULLDUP_bit | RXMAC_EN_bit | RXDMA_EN_bit | TXMAC_EN_bit | TXDMA_EN_bit | CRC_APD_bit;
-   }
-   else {
-     MAC_CR_Register = SPEED_100M_MODE_bit | FULLDUP_bit | RXMAC_EN_bit | RXDMA_EN_bit | TXMAC_EN_bit | TXDMA_EN_bit | CRC_APD_bit;
-   }
- 
--  if (CONFIG_MAC1_PHY_SETTING != 2) {
--    Chip_ID = ((phy_read_register (dev, 0x02, 0)) << 16);
--    Chip_ID |= (phy_read_register (dev, 0x03, 0) & 0xffff);
-+  if (CONFIG_ASPEED_MAC_PHY_SETTING != 2) {
-+    Chip_ID = ((phy_read_register (dev, 0x02, g_phy_addr)) << 16);
-+    Chip_ID |= (phy_read_register (dev, 0x03, g_phy_addr) & 0xffff);
-     if (((Chip_ID & PHYID_VENDOR_MASK) == PHYID_VENDOR_BROADCOM) ||
-         ((Chip_ID & PHYID_VENDOR_MODEL_MASK) == PHYID_RTL8201EL)) {
--      Advertise = phy_read_register (dev, 0x04, 0);
--      Link_Partner = phy_read_register (dev, 0x05, 0);
-+      Advertise = phy_read_register (dev, 0x04, g_phy_addr);
-+      Link_Partner = phy_read_register (dev, 0x05, g_phy_addr);
-       Advertise = (Advertise & PHY_SPEED_DUPLEX_MASK);
-       Link_Partner = (Link_Partner & PHY_SPEED_DUPLEX_MASK);
-       if ((Advertise & Link_Partner) & PHY_100M_DUPLEX) {
-@@ -1456,7 +1490,8 @@ static void set_mac_control_register (struct eth_device* dev)
- //Max waiting time = (20 + 2)ms * 250(PHY_LOOP) = 5.5s
-       do {
-         udelay (20000);
--        Resolved_Status = (phy_read_register (dev, 0x11, 0) & RESOLVED_BIT);
-+        Resolved_Status = (phy_read_register (dev, 0x11, g_phy_addr)
-+                           & RESOLVED_BIT);
-         Loop_Count++;
-         if (Loop_Count >= PHY_LOOP) {
-           PHY_Ready = 0;
-@@ -1466,7 +1501,7 @@ static void set_mac_control_register (struct eth_device* dev)
-       } while (Resolved_Status != RESOLVED_BIT);
- 
-       if (PHY_Ready == 1) {
--        PHY_Status = phy_read_register (dev, 0x11, 0);
-+        PHY_Status = phy_read_register (dev, 0x11, g_phy_addr);
-         PHY_Speed = (PHY_Status & PHY_SPEED_MASK) >> 14;
-         PHY_Duplex = (PHY_Status & PHY_DUPLEX_MASK) >> 13;
- 
-@@ -1485,40 +1520,54 @@ static void set_mac_control_register (struct eth_device* dev)
-       }
- //LED Control
- //              if (Chip_ID == 0x1C) {
--//                  PHY_Status = phy_read_register (dev, 0x18, 0);
--//                phy_write_register (dev, 0x18, 0, (PHY_Status | 0x09));
-+//                  PHY_Status = phy_read_register (dev, 0x18, g_phy_addr);
-+//                phy_write_register (dev, 0x18, g_phy_addr, (PHY_Status | 0x09));
- //              }
- //LED Control D[0], D[6]
- //              if (Chip_ID == 0x141) {
--//                  PHY_Status = phy_read_register (dev, 0x18, 0);
--//                phy_write_register (dev, 0x18, 0, ((PHY_Status & ~(0x41)) | 0x01));
-+//                  PHY_Status = phy_read_register (dev, 0x18, g_phy_addr);
-+//                phy_write_register (dev, 0x18, g_phy_addr, ((PHY_Status & ~(0x41)) | 0x01));
- //              }
-     }
--    else if (Chip_ID == PHYID_BCM54612E )  {
--      phy_write_register ( dev, 0x1C, 1, 0x8C00 ); // Disable GTXCLK Clock Delay Enable
--      phy_write_register ( dev, 0x18, 1, 0xF0E7 ); // Disable RGMII RXD to RXC Skew
--
--      Advertise = phy_read_register (dev, 0x04, 1);
--      Link_Partner = phy_read_register (dev, 0x05, 1);
--      Advertise = (Advertise & PHY_SPEED_DUPLEX_MASK);
--      Link_Partner = (Link_Partner & PHY_SPEED_DUPLEX_MASK);
--      if ((Advertise & Link_Partner) & PHY_100M_DUPLEX) {
--        MAC_CR_Register |= SPEED_100M_MODE_bit;
--        MAC_CR_Register |= FULLDUP_bit;
-+    else if (Chip_ID == PHYID_BCM54612E || Chip_ID == PHYID_BCM54616S) {
-+      // Disable GTXCLK Clock Delay Enable
-+      phy_write_register( dev, 0x1C, g_phy_addr, 0x8C00);
-+      // Disable RGMII RXD to RXC Skew
-+      phy_write_register( dev, 0x18, g_phy_addr, 0xF0E7);
-+      // First Switch shadow register selector
-+      phy_write_register(dev, 0x1C, g_phy_addr, 0x2000);
-+      PHY_Status = phy_read_register(dev, 0x1C, g_phy_addr);
-+      PHY_Duplex = (PHY_Status & 0x0080);
-+      switch (PHY_Status & 0x0018) {
-+      case 0x0000:
-+        PHY_Speed = SPEED_1000M;
-+        break;
-+      case 0x0008:
-+        PHY_Speed = SPEED_100M;
-+        break;
-+      case 0x0010:
-+        PHY_Speed = SPEED_10M;
-+        break;
-+      default:
-+        PHY_Speed = SPEED_100M;
-+        break;
-       }
--      else if ((Advertise & Link_Partner) & PHY_100M_HALF) {
--        MAC_CR_Register |= SPEED_100M_MODE_bit;
--        MAC_CR_Register &= ~FULLDUP_bit;
-+      if (PHY_Speed == SPEED_1000M) {
-+        MAC_CR_Register |= GMAC_MODE_bit;
-+      } else {
-+        MAC_CR_Register &= ~GMAC_MODE_bit;
-+        if (PHY_Speed == SPEED_100M) {
-+          MAC_CR_Register |= SPEED_100M_MODE_bit;
-+        } else {
-+          MAC_CR_Register &= ~SPEED_100M_MODE_bit;
-+        }
-       }
--      else if ((Advertise & Link_Partner) & PHY_10M_DUPLEX) {
--        MAC_CR_Register &= ~SPEED_100M_MODE_bit;
-+      if (PHY_Duplex) {
-         MAC_CR_Register |= FULLDUP_bit;
--      }
--      else if ((Advertise & Link_Partner) & PHY_10M_HALF) {
--        MAC_CR_Register &= ~SPEED_100M_MODE_bit;
-+      } else {
-         MAC_CR_Register &= ~FULLDUP_bit;
-       }
--    }else {
-+    } else {
-       printf("Unknow Chip_ID %x\n",Chip_ID);
-     }
-   }
-diff --git a/include/configs/wedge.h b/include/configs/wedge.h
-new file mode 100644
-index 0000000..6bb7639
---- /dev/null
-+++ b/include/configs/wedge.h
-@@ -0,0 +1,350 @@
-+/*
-+ * Copyright 2004-present Facebook. All Rights Reserved.
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License as
-+ * published by the Free Software Foundation; either version 2 of
-+ * the License, or (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-+ * MA 02111-1307 USA
-+ */
-+
-+#ifndef __CONFIG_H
-+#define __CONFIG_H
-+
-+/* Uncommit the following line to enable JTAG in u-boot */
-+//#define CONFIG_ASPEED_ENABLE_JTAG
-+
-+/*
-+ * High Level Configuration Options
-+ * (easy to change)
-+ */
-+//#define CONFIG_INIT_CRITICAL			/* define for U-BOOT 1.1.1 */
-+#undef  CONFIG_INIT_CRITICAL			/* undef for  U-BOOT 1.1.4 */
-+//#define CONFIG_FPGA_ASPEED	1
-+#define CONFIG_ARM926EJS	1		/* This is an arm926ejs CPU */
-+#define	CONFIG_ASPEED		1
-+#define CONFIG_AST2400		1
-+//#define CONFIG_AST1070		1
-+//#define CONFIG_SYS_FLASH_CFI			/* CONFIG_FLASH_CFI, CONFIG_FLASH_SPI is exclusive*/
-+#define CONFIG_FLASH_SPI
-+//#define CONFIG_2SPIFLASH			/* Boot SPI: CS2, 2nd SPI: CS0 */
-+#undef CONFIG_2SPIFLASH
-+#undef CONFIG_ASPEED_SLT
-+#define CONFIG_FLASH_AST2300
-+//#define CONFIG_FLASH_AST2300_DMA
-+//#define CONFIG_FLASH_SPIx2_Dummy
-+//#define CONFIG_FLASH_SPIx4_Dummy
-+#define CONFIG_CRT_DISPLAY	1		/* undef if not support CRT */
-+
-+//#define CONFIG_USE_IRQ				/* we don't need IRQ/FIQ stuff */
-+#define CONFIG_MISC_INIT_R
-+
-+/*
-+ * DRAM Config
-+ *
-+ * 1. DRAM Size              //
-+ *    CONFIG_DRAM_512MBIT    // 512M bit
-+ *    CONFIG_DRAM_1GBIT      // 1G   bit (default)
-+ *    CONFIG_DRAM_2GBIT      // 2G   bit
-+ *    CONFIG_DRAM_4GBIT      // 4G   bit
-+ * 2. DRAM Speed             //
-+ *    CONFIG_DRAM_336        // 336MHz (DDR-667)
-+ *    CONFIG_DRAM_408        // 408MHz (DDR-800) (default)
-+ * 3. VGA Mode
-+ *    CONFIG_CRT_DISPLAY     // define to disable VGA function
-+ * 4. ECC Function enable
-+ *    CONFIG_DRAM_ECC        // define to enable ECC function
-+ * 5. UART Debug Message
-+ *    CONFIG_DRAM_UART_OUT   // enable output message at UART5
-+ *    CONFIG_DRAM_UART_38400 // set the UART baud rate to 38400, default is 115200
-+ */
-+
-+//1. DRAM Size
-+//#define    CONFIG_DRAM_512MBIT
-+#define    CONFIG_DRAM_1GBIT
-+//#define    CONFIG_DRAM_2GBIT
-+//#define    CONFIG_DRAM_4GBIT
-+//2. DRAM Speed
-+//#define    CONFIG_DRAM_336
-+#define    CONFIG_DRAM_408
-+//3. VGA Mode
-+//#define    CONFIG_CRT_DISPLAY
-+//4. ECC Function enable
-+//#define    CONFIG_DRAM_ECC
-+//5. UART Debug Message
-+#define    CONFIG_DRAM_UART_OUT
-+//#define    CONFIG_DRAM_UART_38400
-+
-+
-+
-+/*
-+ * Environment Config
-+ */
-+#define CONFIG_CMDLINE_TAG	 1		/* enable passing of ATAGs	*/
-+#define CONFIG_SETUP_MEMORY_TAGS 1
-+#define CONFIG_INITRD_TAG	 1
-+#define	CONFIG_BOOTARGS 	"debug console=ttyS2,9600n8 root=/dev/ram rw"
-+#define CONFIG_UPDATE           "tftp 40800000 ast2400.scr; so 40800000'"
-+
-+#define CONFIG_BOOTDELAY	3		/* autoboot after 3 seconds	*/
-+#define CONFIG_AUTOBOOT_KEYED
-+#define CONFIG_AUTOBOOT_PROMPT		\
-+	"autoboot in %d seconds (stop with 'Delete' key)...\n", bootdelay
-+#define CONFIG_AUTOBOOT_STOP_STR	"\x1b\x5b\x33\x7e" /* 'Delete', ESC[3~ */
-+#define CONFIG_ZERO_BOOTDELAY_CHECK
-+
-+#ifdef CONFIG_FLASH_AST2300
-+#define CONFIG_BOOTCOMMAND	"bootm 20080000 20300000"
-+#else
-+#ifdef	CONFIG_SYS_FLASH_CFI
-+#define CONFIG_BOOTCOMMAND	"bootm 10080000 10300000"
-+#else
-+#define CONFIG_BOOTCOMMAND	"bootm 14080000 14300000"
-+#endif
-+#endif
-+#define CONFIG_BOOTFILE		"all.bin"
-+#define CONFIG_ENV_OVERWRITE
-+
-+/*
-+ * Command line configuration.
-+ */
-+#include <config_cmd_default.h>
-+
-+#define CONFIG_CMD_DFL
-+#define CONFIG_CMD_ENV
-+#define CONFIG_CMD_FLASH
-+#define CONFIG_CMD_MII
-+#define CONFIG_CMD_NET
-+#define CONFIG_CMD_PING
-+#define CONFIG_CMD_I2C
-+#define CONFIG_CMD_EEPROM
-+#define CONFIG_CMD_NETTEST
-+#define CONFIG_CMD_SLT
-+
-+/*
-+ * CPU Setting
-+ */
-+#define CPU_CLOCK_RATE		18000000	/* 16.5 MHz clock for the ARM core */
-+
-+/*
-+ * Size of malloc() pool
-+ */
-+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 768*1024)
-+#define CONFIG_SYS_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
-+
-+/*
-+ * Stack sizes,  The stack sizes are set up in start.S using the settings below
-+ */
-+#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
-+#define CONFIG_STACKSIZE_IRQ	(4*1024)	/* IRQ stack */
-+#define CONFIG_STACKSIZE_FIQ	(4*1024)	/* FIQ stack */
-+
-+/*
-+ * Memory Configuration
-+ */
-+#define CONFIG_NR_DRAM_BANKS	1	   	/* we have 1 bank of DRAM */
-+#define PHYS_SDRAM_1		  0x40000000 	/* SDRAM Bank #1 */
-+#define PHYS_SDRAM_1_SIZE	0x10000000 	/* 256 MB */
-+
-+#define CONFIG_SYS_SDRAM_BASE	0x40000000
-+
-+/*
-+ * FLASH Configuration
-+ */
-+#ifdef CONFIG_SYS_FLASH_CFI				/* NOR Flash */
-+
-+#ifdef CONFIG_FLASH_AST2300
-+#define PHYS_FLASH_1			0x20000000 	/* Flash Bank #1 */
-+#else
-+#define PHYS_FLASH_1			0x10000000 	/* Flash Bank #1 */
-+#endif
-+
-+#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1
-+#define CONFIG_FLASH_BANKS_LIST 	{ PHYS_FLASH_1 }
-+
-+#define CONFIG_SYS_MAX_FLASH_BANKS 	1
-+#define CONFIG_SYS_MAX_FLASH_SECT	(256)		/* max number of sectors on one chip */
-+
-+#define CONFIG_ENV_IS_IN_FLASH	1
-+#define CONFIG_ENV_OFFSET					0x60000 	/* environment starts here  */
-+#define CONFIG_ENV_SIZE					0x20000 	/* Total Size of Environment Sector */
-+
-+#define CONFIG_SYS_FLASH_CFI_AMD_RESET
-+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-+
-+#else						/* SPI Flash */
-+
-+#ifdef CONFIG_FLASH_AST2300
-+#define PHYS_FLASH_1		0x20000000 	/* Flash Bank #1 */
-+#else
-+#define PHYS_FLASH_1		0x14000000 	/* Flash Bank #1 */
-+#define PHYS_FLASH_2		0x14800000 	/* Flash Bank #2 */
-+#define PHYS_FLASH_2_BASE	0x10000000
-+#endif
-+
-+#ifdef CONFIG_2SPIFLASH
-+#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_2_BASE
-+#define CONFIG_FLASH_BANKS_LIST 	{ PHYS_FLASH_1, PHYS_FLASH_2 }
-+#define CONFIG_SYS_MAX_FLASH_BANKS 	2
-+#define CONFIG_SYS_MAX_FLASH_SECT	(1024)		/* max number of sectors on one chip */
-+
-+#define CONFIG_ENV_IS_IN_FLASH		1
-+#define CONFIG_ENV_OFFSET		0x7F0000 	/* environment starts here  */
-+#define CONFIG_ENV_SIZE			0x010000 	/* Total Size of Environment Sector */
-+#else
-+#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1
-+#define CONFIG_FLASH_BANKS_LIST 	{ PHYS_FLASH_1 }
-+#define CONFIG_SYS_MAX_FLASH_BANKS 	1
-+#define CONFIG_SYS_MAX_FLASH_SECT	(1024)		/* max number of sectors on one chip */
-+
-+#define CONFIG_ENV_IS_IN_FLASH		1
-+#define CONFIG_ENV_OFFSET		0x60000 	/* environment starts here  */
-+#define CONFIG_ENV_SIZE			0x20000 	/* Total Size of Environment Sector */
-+#define CONFIG_ASPEED_WRITE_DEFAULT_ENV
-+#endif
-+
-+#endif
-+
-+#define __LITTLE_ENDIAN                 1
-+
-+#define CONFIG_MONITOR_BASE		TEXT_BASE
-+#define CONFIG_MONITOR_LEN		(192 << 10)
-+
-+/* timeout values are in ticks */
-+#define CONFIG_SYS_FLASH_ERASE_TOUT	(20*CONFIG_SYS_HZ) 	/* Timeout for Flash Erase */
-+#define CONFIG_SYS_FLASH_WRITE_TOUT	(20*CONFIG_SYS_HZ) 	/* Timeout for Flash Write */
-+
-+/*
-+ * Miscellaneous configurable options
-+ */
-+#define CONFIG_SYS_LONGHELP				/* undef to save memory		*/
-+
-+#define CONFIG_SYS_PROMPT		"boot# " 	/* Monitor Command Prompt	*/
-+#define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-+#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-+
-+#define CONFIG_SYS_MEMTEST_START	0x40000000	/* memtest works on	*/
-+#define CONFIG_SYS_MEMTEST_END		0x44FFFFFF	/* 256 MB in DRAM	*/
-+
-+#define CONFIG_SYS_LOAD_ADDR		0x43000000	/* default load address */
-+
-+#define CONFIG_SYS_TIMERBASE		0x1E782000	/* use timer 1 */
-+#define CONFIG_SYS_HZ			      1000
-+#define CONFIG_ASPEED_TIMER_CLK (1*1000*1000) /* use external clk (1M) */
-+
-+/*
-+ * Serial Configuration
-+ */
-+#define CONFIG_SYS_NS16550
-+#define CONFIG_SYS_NS16550_SERIAL
-+#define CONFIG_SYS_NS16550_MEM32
-+#define CONFIG_SYS_NS16550_REG_SIZE	-4
-+#define CONFIG_SYS_NS16550_CLK		24000000
-+#define CONFIG_SYS_NS16550_COM1		0x1e783000
-+#define CONFIG_SYS_NS16550_COM2		0x1e784000
-+#define CONFIG_SYS_NS16550_COM3		0x1e78e000
-+#define	CONFIG_SYS_LOADS_BAUD_CHANGE
-+#define CONFIG_CONS_INDEX		2
-+#define CONFIG_BAUDRATE			9600
-+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-+#define CONFIG_ASPEED_COM 0x1e78e000 // COM3
-+#define CONFIG_ASPEED_COM_IER (CONFIG_ASPEED_COM + 0x4)
-+#define CONFIG_ASPEED_COM_IIR (CONFIG_ASPEED_COM + 0x8)
-+#define CONFIG_ASPEED_COM_LCR (CONFIG_ASPEED_COM + 0xc)
-+
-+/*
-+ * USB device configuration
-+ */
-+/*
-+#define CONFIG_USB_DEVICE		1
-+#define CONFIG_USB_TTY			1
-+
-+#define CONFIG_USBD_VENDORID		0x1234
-+#define CONFIG_USBD_PRODUCTID		0x5678
-+#define CONFIG_USBD_MANUFACTURER	"Siemens"
-+#define CONFIG_USBD_PRODUCT_NAME	"SX1"
-+*/
-+
-+/*
-+ * I2C configuration
-+ */
-+#define CONFIG_HARD_I2C
-+#define CONFIG_SYS_I2C_SPEED		100000
-+#define CONFIG_SYS_I2C_SLAVE		1
-+#define CONFIG_DRIVER_ASPEED_I2C
-+
-+/*
-+* EEPROM configuration
-+*/
-+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 	2
-+#define CONFIG_SYS_I2C_EEPROM_ADDR 	0xa0
-+
-+#define __BYTE_ORDER __LITTLE_ENDIAN
-+#define __LITTLE_ENDIAN_BITFIELD
-+
-+/*
-+ * NIC configuration
-+ */
-+#define CONFIG_ASPEEDNIC
-+#define CONFIG_NET_MULTI
-+#define CONFIG_MAC1_PHY_LINK_INTERRUPT
-+#define CONFIG_MAC2_ENABLE
-+#define CONFIG_MAC2_PHY_LINK_INTERRUPT
-+/*
-+*-------------------------------------------------------------------------------
-+* NOTICE: MAC1 and MAC2 now have their own seperate PHY configuration.
-+* We use 2 bits for each MAC in the scratch register(D[15:11] in 0x1E6E2040) to
-+* inform kernel driver.
-+* The meanings of the 2 bits are:
-+* 00(0): Dedicated PHY
-+* 01(1): ASPEED's EVA + INTEL's NC-SI PHY chip EVA
-+* 10(2): ASPEED's MAC is connected to NC-SI PHY chip directly
-+* 11: Reserved
-+*
-+* We use CONFIG_MAC1_PHY_SETTING and CONFIG_MAC2_PHY_SETTING in U-Boot
-+* 0: Dedicated PHY
-+* 1: ASPEED's EVA + INTEL's NC-SI PHY chip EVA
-+* 2: ASPEED's MAC is connected to NC-SI PHY chip directly
-+* 3: Reserved
-+*-------------------------------------------------------------------------------
-+*/
-+#define CONFIG_MAC1_PHY_SETTING		0
-+#define CONFIG_MAC2_PHY_SETTING		0
-+#define CONFIG_ASPEED_MAC_NUMBER  2
-+#define CONFIG_ASPEED_MAC_CONFIG  2 // config MAC2
-+#define _PHY_SETTING_CONCAT(mac) CONFIG_MAC##mac##_PHY_SETTING
-+#define _GET_MAC_PHY_SETTING(mac) _PHY_SETTING_CONCAT(mac)
-+#define CONFIG_ASPEED_MAC_PHY_SETTING \
-+  _GET_MAC_PHY_SETTING(CONFIG_ASPEED_MAC_CONFIG)
-+#define CONFIG_MAC_INTERFACE_CLOCK_DELAY	0x2255
-+#define CONFIG_RANDOM_MACADDR
-+//#define CONFIG_GATEWAYIP 192.168.0.1
-+//#define CONFIG_NETMASK   255.255.255.0
-+//#define CONFIG_IPADDR    192.168.0.45
-+//#define CONFIG_SERVERIP  192.168.0.81
-+
-+/*
-+ * SLT
-+ */
-+/*
-+#define CONFIG_SLT
-+#define CFG_CMD_SLT		(CFG_CMD_VIDEOTEST | CFG_CMD_MACTEST | CFG_CMD_HACTEST | CFG_CMD_MICTEST)
-+*/
-+
-+#define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
-+
-+#define CONFIG_ASPEED_ENABLE_WATCHDOG
-+#define CONFIG_ASPEED_WATCHDOG_TIMEOUT (5*60) // 5m
-+
-+#endif	/* __CONFIG_H */
-diff --git a/include/configs/palmetto.h b/include/configs/palmetto.h
-new file mode 100644
-index 0000000..6bb7639
---- /dev/null
-+++ b/include/configs/palmetto.h
-@@ -0,0 +1,350 @@
-+/*
-+ * Copyright 2004-present Facebook. All Rights Reserved.
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License as
-+ * published by the Free Software Foundation; either version 2 of
-+ * the License, or (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-+ * MA 02111-1307 USA
-+ */
-+
-+#ifndef __CONFIG_H
-+#define __CONFIG_H
-+
-+/* Uncommit the following line to enable JTAG in u-boot */
-+//#define CONFIG_ASPEED_ENABLE_JTAG
-+
-+/*
-+ * High Level Configuration Options
-+ * (easy to change)
-+ */
-+//#define CONFIG_INIT_CRITICAL			/* define for U-BOOT 1.1.1 */
-+#undef  CONFIG_INIT_CRITICAL			/* undef for  U-BOOT 1.1.4 */
-+//#define CONFIG_FPGA_ASPEED	1
-+#define CONFIG_ARM926EJS	1		/* This is an arm926ejs CPU */
-+#define	CONFIG_ASPEED		1
-+#define CONFIG_AST2400		1
-+//#define CONFIG_AST1070		1
-+//#define CONFIG_SYS_FLASH_CFI			/* CONFIG_FLASH_CFI, CONFIG_FLASH_SPI is exclusive*/
-+#define CONFIG_FLASH_SPI
-+//#define CONFIG_2SPIFLASH			/* Boot SPI: CS2, 2nd SPI: CS0 */
-+#undef CONFIG_2SPIFLASH
-+#undef CONFIG_ASPEED_SLT
-+#define CONFIG_FLASH_AST2300
-+//#define CONFIG_FLASH_AST2300_DMA
-+//#define CONFIG_FLASH_SPIx2_Dummy
-+//#define CONFIG_FLASH_SPIx4_Dummy
-+#define CONFIG_CRT_DISPLAY	1		/* undef if not support CRT */
-+
-+//#define CONFIG_USE_IRQ				/* we don't need IRQ/FIQ stuff */
-+#define CONFIG_MISC_INIT_R
-+
-+/*
-+ * DRAM Config
-+ *
-+ * 1. DRAM Size              //
-+ *    CONFIG_DRAM_512MBIT    // 512M bit
-+ *    CONFIG_DRAM_1GBIT      // 1G   bit (default)
-+ *    CONFIG_DRAM_2GBIT      // 2G   bit
-+ *    CONFIG_DRAM_4GBIT      // 4G   bit
-+ * 2. DRAM Speed             //
-+ *    CONFIG_DRAM_336        // 336MHz (DDR-667)
-+ *    CONFIG_DRAM_408        // 408MHz (DDR-800) (default)
-+ * 3. VGA Mode
-+ *    CONFIG_CRT_DISPLAY     // define to disable VGA function
-+ * 4. ECC Function enable
-+ *    CONFIG_DRAM_ECC        // define to enable ECC function
-+ * 5. UART Debug Message
-+ *    CONFIG_DRAM_UART_OUT   // enable output message at UART5
-+ *    CONFIG_DRAM_UART_38400 // set the UART baud rate to 38400, default is 115200
-+ */
-+
-+//1. DRAM Size
-+//#define    CONFIG_DRAM_512MBIT
-+#define    CONFIG_DRAM_1GBIT
-+//#define    CONFIG_DRAM_2GBIT
-+//#define    CONFIG_DRAM_4GBIT
-+//2. DRAM Speed
-+//#define    CONFIG_DRAM_336
-+#define    CONFIG_DRAM_408
-+//3. VGA Mode
-+//#define    CONFIG_CRT_DISPLAY
-+//4. ECC Function enable
-+//#define    CONFIG_DRAM_ECC
-+//5. UART Debug Message
-+#define    CONFIG_DRAM_UART_OUT
-+//#define    CONFIG_DRAM_UART_38400
-+
-+
-+
-+/*
-+ * Environment Config
-+ */
-+#define CONFIG_CMDLINE_TAG	 1		/* enable passing of ATAGs	*/
-+#define CONFIG_SETUP_MEMORY_TAGS 1
-+#define CONFIG_INITRD_TAG	 1
-+#define	CONFIG_BOOTARGS 	"debug console=ttyS4,38400n8 root=/dev/ram rw"
-+#define CONFIG_UPDATE           "tftp 40800000 ast2400.scr; so 40800000'"
-+
-+#define CONFIG_BOOTDELAY	3		/* autoboot after 3 seconds	*/
-+#define CONFIG_AUTOBOOT_KEYED
-+#define CONFIG_AUTOBOOT_PROMPT		\
-+	"autoboot in %d seconds (stop with 'Delete' key)...\n", bootdelay
-+#define CONFIG_AUTOBOOT_STOP_STR	"\x1b\x5b\x33\x7e" /* 'Delete', ESC[3~ */
-+#define CONFIG_ZERO_BOOTDELAY_CHECK
-+
-+#ifdef CONFIG_FLASH_AST2300
-+#define CONFIG_BOOTCOMMAND	"bootm 20080000 20300000"
-+#else
-+#ifdef	CONFIG_SYS_FLASH_CFI
-+#define CONFIG_BOOTCOMMAND	"bootm 10080000 10300000"
-+#else
-+#define CONFIG_BOOTCOMMAND	"bootm 14080000 14300000"
-+#endif
-+#endif
-+#define CONFIG_BOOTFILE		"all.bin"
-+#define CONFIG_ENV_OVERWRITE
-+
-+/*
-+ * Command line configuration.
-+ */
-+#include <config_cmd_default.h>
-+
-+#define CONFIG_CMD_DFL
-+#define CONFIG_CMD_ENV
-+#define CONFIG_CMD_FLASH
-+#define CONFIG_CMD_MII
-+#define CONFIG_CMD_NET
-+#define CONFIG_CMD_PING
-+#define CONFIG_CMD_I2C
-+#define CONFIG_CMD_EEPROM
-+#define CONFIG_CMD_NETTEST
-+#define CONFIG_CMD_SLT
-+
-+/*
-+ * CPU Setting
-+ */
-+#define CPU_CLOCK_RATE		18000000	/* 16.5 MHz clock for the ARM core */
-+
-+/*
-+ * Size of malloc() pool
-+ */
-+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 768*1024)
-+#define CONFIG_SYS_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
-+
-+/*
-+ * Stack sizes,  The stack sizes are set up in start.S using the settings below
-+ */
-+#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
-+#define CONFIG_STACKSIZE_IRQ	(4*1024)	/* IRQ stack */
-+#define CONFIG_STACKSIZE_FIQ	(4*1024)	/* FIQ stack */
-+
-+/*
-+ * Memory Configuration
-+ */
-+#define CONFIG_NR_DRAM_BANKS	1	   	/* we have 1 bank of DRAM */
-+#define PHYS_SDRAM_1		  0x40000000 	/* SDRAM Bank #1 */
-+#define PHYS_SDRAM_1_SIZE	0x10000000 	/* 256 MB */
-+
-+#define CONFIG_SYS_SDRAM_BASE	0x40000000
-+
-+/*
-+ * FLASH Configuration
-+ */
-+#ifdef CONFIG_SYS_FLASH_CFI				/* NOR Flash */
-+
-+#ifdef CONFIG_FLASH_AST2300
-+#define PHYS_FLASH_1			0x20000000 	/* Flash Bank #1 */
-+#else
-+#define PHYS_FLASH_1			0x10000000 	/* Flash Bank #1 */
-+#endif
-+
-+#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1
-+#define CONFIG_FLASH_BANKS_LIST 	{ PHYS_FLASH_1 }
-+
-+#define CONFIG_SYS_MAX_FLASH_BANKS 	1
-+#define CONFIG_SYS_MAX_FLASH_SECT	(256)		/* max number of sectors on one chip */
-+
-+#define CONFIG_ENV_IS_IN_FLASH	1
-+#define CONFIG_ENV_OFFSET					0x60000 	/* environment starts here  */
-+#define CONFIG_ENV_SIZE					0x20000 	/* Total Size of Environment Sector */
-+
-+#define CONFIG_SYS_FLASH_CFI_AMD_RESET
-+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-+
-+#else						/* SPI Flash */
-+
-+#ifdef CONFIG_FLASH_AST2300
-+#define PHYS_FLASH_1		0x20000000 	/* Flash Bank #1 */
-+#else
-+#define PHYS_FLASH_1		0x14000000 	/* Flash Bank #1 */
-+#define PHYS_FLASH_2		0x14800000 	/* Flash Bank #2 */
-+#define PHYS_FLASH_2_BASE	0x10000000
-+#endif
-+
-+#ifdef CONFIG_2SPIFLASH
-+#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_2_BASE
-+#define CONFIG_FLASH_BANKS_LIST 	{ PHYS_FLASH_1, PHYS_FLASH_2 }
-+#define CONFIG_SYS_MAX_FLASH_BANKS 	2
-+#define CONFIG_SYS_MAX_FLASH_SECT	(1024)		/* max number of sectors on one chip */
-+
-+#define CONFIG_ENV_IS_IN_FLASH		1
-+#define CONFIG_ENV_OFFSET		0x7F0000 	/* environment starts here  */
-+#define CONFIG_ENV_SIZE			0x010000 	/* Total Size of Environment Sector */
-+#else
-+#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1
-+#define CONFIG_FLASH_BANKS_LIST 	{ PHYS_FLASH_1 }
-+#define CONFIG_SYS_MAX_FLASH_BANKS 	1
-+#define CONFIG_SYS_MAX_FLASH_SECT	(1024)		/* max number of sectors on one chip */
-+
-+#define CONFIG_ENV_IS_IN_FLASH		1
-+#define CONFIG_ENV_OFFSET		0x60000 	/* environment starts here  */
-+#define CONFIG_ENV_SIZE			0x20000 	/* Total Size of Environment Sector */
-+#define CONFIG_ASPEED_WRITE_DEFAULT_ENV
-+#endif
-+
-+#endif
-+
-+#define __LITTLE_ENDIAN                 1
-+
-+#define CONFIG_MONITOR_BASE		TEXT_BASE
-+#define CONFIG_MONITOR_LEN		(192 << 10)
-+
-+/* timeout values are in ticks */
-+#define CONFIG_SYS_FLASH_ERASE_TOUT	(20*CONFIG_SYS_HZ) 	/* Timeout for Flash Erase */
-+#define CONFIG_SYS_FLASH_WRITE_TOUT	(20*CONFIG_SYS_HZ) 	/* Timeout for Flash Write */
-+
-+/*
-+ * Miscellaneous configurable options
-+ */
-+#define CONFIG_SYS_LONGHELP				/* undef to save memory		*/
-+
-+#define CONFIG_SYS_PROMPT		"boot# " 	/* Monitor Command Prompt	*/
-+#define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-+#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-+
-+#define CONFIG_SYS_MEMTEST_START	0x40000000	/* memtest works on	*/
-+#define CONFIG_SYS_MEMTEST_END		0x44FFFFFF	/* 256 MB in DRAM	*/
-+
-+#define CONFIG_SYS_LOAD_ADDR		0x43000000	/* default load address */
-+
-+#define CONFIG_SYS_TIMERBASE		0x1E782000	/* use timer 1 */
-+#define CONFIG_SYS_HZ			      1000
-+#define CONFIG_ASPEED_TIMER_CLK (1*1000*1000) /* use external clk (1M) */
-+
-+/*
-+ * Serial Configuration
-+ */
-+#define CONFIG_SYS_NS16550
-+#define CONFIG_SYS_NS16550_SERIAL
-+#define CONFIG_SYS_NS16550_MEM32
-+#define CONFIG_SYS_NS16550_REG_SIZE	-4
-+#define CONFIG_SYS_NS16550_CLK		24000000
-+#define CONFIG_SYS_NS16550_COM1		0x1e783000
-+#define CONFIG_SYS_NS16550_COM2		0x1e784000
-+#define CONFIG_SYS_NS16550_COM3		0x1e78e000
-+#define	CONFIG_SYS_LOADS_BAUD_CHANGE
-+#define CONFIG_CONS_INDEX		2
-+#define CONFIG_BAUDRATE			38400
-+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-+#define CONFIG_ASPEED_COM 0x1e784000 // UART5
-+#define CONFIG_ASPEED_COM_IER (CONFIG_ASPEED_COM + 0x4)
-+#define CONFIG_ASPEED_COM_IIR (CONFIG_ASPEED_COM + 0x8)
-+#define CONFIG_ASPEED_COM_LCR (CONFIG_ASPEED_COM + 0xc)
-+
-+/*
-+ * USB device configuration
-+ */
-+/*
-+#define CONFIG_USB_DEVICE		1
-+#define CONFIG_USB_TTY			1
-+
-+#define CONFIG_USBD_VENDORID		0x1234
-+#define CONFIG_USBD_PRODUCTID		0x5678
-+#define CONFIG_USBD_MANUFACTURER	"Siemens"
-+#define CONFIG_USBD_PRODUCT_NAME	"SX1"
-+*/
-+
-+/*
-+ * I2C configuration
-+ */
-+#define CONFIG_HARD_I2C
-+#define CONFIG_SYS_I2C_SPEED		100000
-+#define CONFIG_SYS_I2C_SLAVE		1
-+#define CONFIG_DRIVER_ASPEED_I2C
-+
-+/*
-+* EEPROM configuration
-+*/
-+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 	2
-+#define CONFIG_SYS_I2C_EEPROM_ADDR 	0xa0
-+
-+#define __BYTE_ORDER __LITTLE_ENDIAN
-+#define __LITTLE_ENDIAN_BITFIELD
-+
-+/*
-+ * NIC configuration
-+ */
-+#define CONFIG_ASPEEDNIC
-+#define CONFIG_NET_MULTI
-+#define CONFIG_MAC1_PHY_LINK_INTERRUPT
-+#define CONFIG_MAC2_ENABLE
-+#define CONFIG_MAC2_PHY_LINK_INTERRUPT
-+/*
-+*-------------------------------------------------------------------------------
-+* NOTICE: MAC1 and MAC2 now have their own seperate PHY configuration.
-+* We use 2 bits for each MAC in the scratch register(D[15:11] in 0x1E6E2040) to
-+* inform kernel driver.
-+* The meanings of the 2 bits are:
-+* 00(0): Dedicated PHY
-+* 01(1): ASPEED's EVA + INTEL's NC-SI PHY chip EVA
-+* 10(2): ASPEED's MAC is connected to NC-SI PHY chip directly
-+* 11: Reserved
-+*
-+* We use CONFIG_MAC1_PHY_SETTING and CONFIG_MAC2_PHY_SETTING in U-Boot
-+* 0: Dedicated PHY
-+* 1: ASPEED's EVA + INTEL's NC-SI PHY chip EVA
-+* 2: ASPEED's MAC is connected to NC-SI PHY chip directly
-+* 3: Reserved
-+*-------------------------------------------------------------------------------
-+*/
-+#define CONFIG_MAC1_PHY_SETTING		2
-+#define CONFIG_MAC2_PHY_SETTING		0
-+#define CONFIG_ASPEED_MAC_NUMBER  1
-+#define CONFIG_ASPEED_MAC_CONFIG  1 // config MAC1
-+#define _PHY_SETTING_CONCAT(mac) CONFIG_MAC##mac##_PHY_SETTING
-+#define _GET_MAC_PHY_SETTING(mac) _PHY_SETTING_CONCAT(mac)
-+#define CONFIG_ASPEED_MAC_PHY_SETTING \
-+  _GET_MAC_PHY_SETTING(CONFIG_ASPEED_MAC_CONFIG)
-+#define CONFIG_MAC_INTERFACE_CLOCK_DELAY	0x2255
-+#define CONFIG_RANDOM_MACADDR
-+//#define CONFIG_GATEWAYIP 192.168.0.1
-+//#define CONFIG_NETMASK   255.255.255.0
-+//#define CONFIG_IPADDR    192.168.0.45
-+//#define CONFIG_SERVERIP  192.168.0.81
-+
-+/*
-+ * SLT
-+ */
-+/*
-+#define CONFIG_SLT
-+#define CFG_CMD_SLT		(CFG_CMD_VIDEOTEST | CFG_CMD_MACTEST | CFG_CMD_HACTEST | CFG_CMD_MICTEST)
-+*/
-+
-+#define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
-+
-+#define CONFIG_ASPEED_ENABLE_WATCHDOG
-+#define CONFIG_ASPEED_WATCHDOG_TIMEOUT (5*60) // 5m
-+
-+#endif	/* __CONFIG_H */
diff --git a/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes-bsp/u-boot/u-boot_2013.07%.bbappend b/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes-bsp/u-boot/u-boot_2013.07%.bbappend
deleted file mode 100644
index 6d4a18f..0000000
--- a/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes-bsp/u-boot/u-boot_2013.07%.bbappend
+++ /dev/null
@@ -1,13 +0,0 @@
-FILESEXTRAPATHS_prepend := "${THISDIR}/files:"
-
-#SRC_URI += "file://fw_env.config
-SRC_URI += "file://patch-2013.07/0000-u-boot-aspeed-064.patch \
-           file://patch-2013.07/0001-u-boot-openbmc.patch \
-           file://config.patch \
-           "
-
-# Do not install u-boot in rootfs
-#do_install[postfuncs] += "remove_uboot_from_rootfs"
-#remove_uboot_from_rootfs() {
-#    rm -rf ${D}/boot/u-boot*
-#}
diff --git a/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes-kernel/linux/linux-obmc_%.bbappend b/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes-kernel/linux/linux-obmc_%.bbappend
deleted file mode 100644
index de6d3d6..0000000
--- a/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes-kernel/linux/linux-obmc_%.bbappend
+++ /dev/null
@@ -1 +0,0 @@
-KERNEL_CONFIG_COMMAND = "oe_runmake_call -C ${S} O=${B} ${KMACHINE}_defconfig"
diff --git a/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes.txt b/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes.txt
deleted file mode 100644
index 149509f..0000000
--- a/meta-openbmc-machines/meta-openpower/meta-ibm/meta-palmetto/recipes.txt
+++ /dev/null
@@ -1,2 +0,0 @@
-recipes-bsp          - Anything with links to specific hardware or hardware configuration information
-recipes-kernel       - The kernel and generic applications/libraries with strong kernel dependencies