| description: > |
| MultiRecord Power Supply Information (Record Type 0x00) |
| In accordance with IPMI Platform Management FRU Information |
| Storage Definition v1.0 Document Revision 1.3, Table 18-1. |
| |
| properties: |
| - name: OveralCapacity |
| type: int64 |
| description: > |
| Offset 0, bits 11..0. |
| Overall capacity (watts) |
| - name: PeakVA |
| type: int64 |
| description: > |
| Offset 2. |
| Peak VA |
| - name: InrushCurrent |
| type: int64 |
| description: > |
| Offset 4. |
| Inrush current |
| - name: InrushInterval |
| type: int64 |
| description: > |
| Offset 5. |
| Inrush interval in ms. |
| - name: LowInputVoltage1 |
| type: int64 |
| description: > |
| Offset 6. |
| Low end Input voltage range 1 (10mV) |
| - name: HighInputVoltage1 |
| type: int64 |
| description: > |
| Offset 8. |
| High end Input voltage range 1 (10mV) |
| - name: LowInputVoltage2 |
| type: int64 |
| description: > |
| Offset 10. |
| Low end Input voltage range 2 (10mV) |
| - name: HighInputVoltage2 |
| type: int64 |
| description: > |
| Offset 12. |
| High end Input voltage range 2 (10mV) |
| - name: LowInputFrequency |
| type: int64 |
| description: > |
| Offset 14. |
| Low end Input frequency range |
| - name: HighInputFrequency |
| type: int64 |
| description: > |
| Offset 15. |
| High end Input frequency range |
| - name: InDropoutTolerance |
| type: int64 |
| description: > |
| Offset 16. |
| Input dropout tolerance in ms |
| - name: TachoPPR_FailPinPolarity |
| type: boolean |
| description: > |
| Offset 17, bit 4. |
| Tachometer pulses per rotation/Predictive fail pin polarity. |
| Meaning depends on PrediciveFailSupport. |
| False means 1 pulse per rotation (for tacho) or assertion indicates failure (for predictive falure pin). |
| True means 2 pulses per rotation (for tacho) or deassertion indicates failure (for predictive falure pin). |
| - name: HotSwap |
| type: boolean |
| description: > |
| Offset 17, bit 3. |
| Hot Swap Support |
| - name: Autoswitch |
| type: boolean |
| description: > |
| Offset 17, bit 2. |
| Autoswitch |
| - name: PowerFactor |
| type: boolean |
| description: > |
| Offset 17, bit 1. |
| Power factor correction |
| - name: PredictiveFailSupport |
| type: boolean |
| description: > |
| Offset 17, bit 0. |
| Predictive fail pin supported. When false, tachometer is used instead. |
| Affects meaning of TachoPPR_FailPinPolarity. |
| - name: HoldUpTime |
| type: int64 |
| description: > |
| Offset 18, bits 15..12. |
| Peak Wattage hold up time in seconds |
| - name: PeakCapacity |
| type: int64 |
| description: > |
| Offset 18, bits 11..0. |
| Peak capacity (watts) |
| - name: Voltage1 |
| type: int64 |
| description: > |
| Offset 20, byte 1, bits 7..4. |
| Combined Wattage Voltage 1 |
| - name: Voltage2 |
| type: int64 |
| description: > |
| Offset 20, byte 1, bits 3..0. |
| Combined Wattage Voltage 2 |
| - name: TotalWattage |
| type: int64 |
| description: > |
| Offset 20, bytes 2..3. |
| Total Combined Wattage |
| - name: TachometerLow |
| type: int64 |
| description: > |
| Offset 23. |
| Predictive fail tachometer lower threshold (RPS). |
| Used when PredictiveFailSupport is false. |