diff --git a/control/json/zone.hpp b/control/json/zone.hpp
new file mode 100644
index 0000000..99c8fa5
--- /dev/null
+++ b/control/json/zone.hpp
@@ -0,0 +1,166 @@
+/**
+ * Copyright © 2020 IBM Corporation
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ *     http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+#pragma once
+
+#include "config_base.hpp"
+
+#include <nlohmann/json.hpp>
+#include <sdbusplus/bus.hpp>
+
+namespace phosphor::fan::control::json
+{
+
+using json = nlohmann::json;
+
+/**
+ * @class Zone - Represents a configured fan control zone
+ *
+ * A zone object contains the configured attributes for a zone that groups
+ * a number of fans together to be under the same speed control. These
+ * configuration attributes include, but are not limited to, the full speed
+ * of the fans within the zone, a default floor speed, the delay between speed
+ * increases, a decrease interval, and any profiles(OPTIONAL) the zone should
+ * be included in.
+ *
+ * (When no profile for a zone is given, the zone defaults to always exist)
+ *
+ */
+class Zone : public ConfigBase
+{
+  public:
+    /* JSON file name for zones */
+    static constexpr auto confFileName = "zones.json";
+
+    Zone() = delete;
+    Zone(const Zone&) = delete;
+    Zone(Zone&&) = delete;
+    Zone& operator=(const Zone&) = delete;
+    Zone& operator=(Zone&&) = delete;
+    ~Zone() = default;
+
+    /**
+     * Constructor
+     * Parses and populates a zone from JSON object data
+     *
+     * @param[in] bus - sdbusplus bus object
+     * @param[in] jsonObj - JSON object
+     */
+    Zone(sdbusplus::bus::bus& bus, const json& jsonObj);
+
+    /**
+     * @brief Get the full speed
+     *
+     * Full speed is the speed set to the fans within this zone unless there
+     * are events configured that alter the fan speeds.
+     *
+     * @return Full speed of this zone
+     */
+    inline const auto& getFullSpeed() const
+    {
+        return _fullSpeed;
+    }
+
+    /**
+     * @brief Get the default floor speed
+     *
+     * The default floor speed is the lowest speed the fans within this zone
+     * are allowed to decrease to. The zone's floor speed defaults to this
+     * unless changed by some configured event.
+     *
+     * @return Default floor speed
+     */
+    inline const auto& getDefaultFloor() const
+    {
+        return _defaultFloor;
+    }
+
+    /**
+     * @brief Get the speed increase delay(OPTIONAL)
+     *
+     * The speed increase delay is the amount of time(in seconds) increases
+     * to a target speed are delayed before being made. The default is 0, which
+     * results in immediate speed increase requests when any events result in
+     * a change to the target speed.
+     *
+     * It is recommend a value other than 0 is configured, but that inherently
+     * depends on the fan controller and configured speed increases.
+     *
+     * @return Speed increase delay(in seconds)
+     */
+    inline const auto& getIncDelay() const
+    {
+        return _incDelay;
+    }
+
+    /**
+     * @brief Get the speed decrease interval
+     *
+     * Speed decreases happen on a set interval when no requests for an increase
+     * in fan speeds exists. This is the interval(in seconds) at which the fans
+     * within the zone are decreased if events exist that result in a target
+     * speed decrease.
+     *
+     * @return Speed decrease interval(in seconds)
+     */
+    inline const auto& getDecInterval() const
+    {
+        return _decInterval;
+    }
+
+  private:
+    /* The zone's full speed value for fans */
+    uint64_t _fullSpeed;
+
+    /* The zone's default floor speed value for fans */
+    uint64_t _defaultFloor;
+
+    /* Zone's speed increase delay(in seconds) (OPTIONAL) */
+    uint64_t _incDelay;
+
+    /* Zone's speed decrease interval(in seconds) */
+    uint64_t _decInterval;
+
+    /**
+     * @brief Parse and set the zone's full speed value
+     *
+     * @param[in] jsonObj - JSON object for the zone
+     *
+     * Sets the full speed value for the zone from the JSON configuration object
+     */
+    void setFullSpeed(const json& jsonObj);
+
+    /**
+     * @brief Parse and set the zone's default floor speed value
+     *
+     * @param[in] jsonObj - JSON object for the zone
+     *
+     * Sets the default floor speed value for the zone from the JSON
+     * configuration object
+     */
+    void setDefaultFloor(const json& jsonObj);
+
+    /**
+     * @brief Parse and set the zone's decrease interval(in seconds)
+     *
+     * @param[in] jsonObj - JSON object for the zone
+     *
+     * Sets the speed decrease interval(in seconds) for the zone from the JSON
+     * configuration object
+     */
+    void setDecInterval(const json& jsonObj);
+};
+
+} // namespace phosphor::fan::control::json