diff --git a/monitor/example/config.json b/monitor/example/config.json
index 53c3421..515eec0 100644
--- a/monitor/example/config.json
+++ b/monitor/example/config.json
@@ -1,184 +1,184 @@
 {
-  "comments": "List of fans with the attributes used to monitor them.",
-  "fans": [
-    {
-      "comments": [
-        "The first fan in the system that has two sensor(dual rotor) feedbacks",
-        "that are allowed to deviate from any given target by 15% for up-to 30",
-        "seconds before being marked nonfunctional in inventory. The first",
-        "sensor object contains the target property and the second sensor",
-        "object's feedback speed is adjusted by a factor of 1.45 and offset",
-        "by -909 to accomodate how its hardware reacts to any given target. It",
-        "takes 1 sensor to mark this fan nonfunctional and once marked",
-        "nonfunctional, the nonfunctional sensor(s) must be within 15% of the",
-        "target for 5 seconds before being updated to functional again.",
-        "Each sensor has an error logged after 0 seconds being marked",
-        "nonfunctional and the fan has an error logged if its been not",
-        "present for 20 seconds.",
-        "In addition, this fan is not monitored for the first 30 seconds after",
-        "a poweron to allow the fan to spin-up."
-      ],
-      "inventory": "/system/chassis/motherboard/fan0",
-      "functional_delay": 5,
-      "allowed_out_of_range_time": 30,
-      "deviation": 15,
-      "num_sensors_nonfunc_for_fan_nonfunc": 1,
-      "monitor_start_delay": 30,
-      "fan_missing_error_delay": 20,
-      "nonfunc_rotor_error_delay": 0,
-      "sensors": [
+    "comments": "List of fans with the attributes used to monitor them.",
+    "fans": [
         {
-          "name": "fan0_0",
-          "has_target": true
+            "comments": [
+                "The first fan in the system that has two sensor(dual rotor) feedbacks",
+                "that are allowed to deviate from any given target by 15% for up-to 30",
+                "seconds before being marked nonfunctional in inventory. The first",
+                "sensor object contains the target property and the second sensor",
+                "object's feedback speed is adjusted by a factor of 1.45 and offset",
+                "by -909 to accomodate how its hardware reacts to any given target. It",
+                "takes 1 sensor to mark this fan nonfunctional and once marked",
+                "nonfunctional, the nonfunctional sensor(s) must be within 15% of the",
+                "target for 5 seconds before being updated to functional again.",
+                "Each sensor has an error logged after 0 seconds being marked",
+                "nonfunctional and the fan has an error logged if its been not",
+                "present for 20 seconds.",
+                "In addition, this fan is not monitored for the first 30 seconds after",
+                "a poweron to allow the fan to spin-up."
+            ],
+            "inventory": "/system/chassis/motherboard/fan0",
+            "functional_delay": 5,
+            "allowed_out_of_range_time": 30,
+            "deviation": 15,
+            "num_sensors_nonfunc_for_fan_nonfunc": 1,
+            "monitor_start_delay": 30,
+            "fan_missing_error_delay": 20,
+            "nonfunc_rotor_error_delay": 0,
+            "sensors": [
+                {
+                    "name": "fan0_0",
+                    "has_target": true
+                },
+                {
+                    "name": "fan0_1",
+                    "has_target": false,
+                    "factor": 1.45,
+                    "offset": -909
+                }
+            ]
         },
         {
-          "name": "fan0_1",
-          "has_target": false,
-          "factor": 1.45,
-          "offset": -909
-        }
-      ]
-    },
-    {
-      "comments": [
-        "The second fan in the system has one sensor(single rotor) feedback",
-        "that is only monitored with the `WaterCooled` property is false. The",
-        "sensor is monitored using a 'count' method where a counter is",
-        "incremented each tick the fan deviates 15% from a target and",
-        "decrements back to zero each tick the fan is within spec. When the",
-        "sensor reaches the threshold of 25 ticks, the fan is marked",
-        "nonfunctional and only returns to being functional when the counter",
-        "is decremented back to 0. This differs from the default 'timebased'",
-        "method where the fan must deviate contiguously for a set amount of",
-        "time to be marked nonfunctional. It takes 1 sensor to mark this fan",
-        "nonfunctional.",
-        "Each sensor has an error logged after 0 seconds being marked",
-        "nonfunctional and the fan has an error logged if its been not present",
-        "for 20 seconds.",
-        "In addition, this fan is not monitored for the first 30 seconds after",
-        "a poweron to allow the fan to spin-up."
-      ],
-      "inventory": "/system/chassis/motherboard/fan1",
-      "method": "count",
-      "deviation": 15,
-      "num_sensors_nonfunc_for_fan_nonfunc": 1,
-      "monitor_start_delay": 30,
-      "fan_missing_error_delay": 20,
-      "nonfunc_rotor_error_delay": 0,
-      "sensors": [
-        {
-          "name": "fan1_0",
-          "has_target": true,
-          "threshold": 25
-        }
-      ],
-      "condition": {
-        "name": "propertiesMatch",
-        "properties": [
-          {
-            "object": "/xyz/openbmc_project/inventory/system/chassis",
-            "interface": "xyz.openbmc_project.Inventory.Decorator.CoolingType",
-            "property": {
-              "name": "WaterCooled",
-              "type": "bool",
-              "value": false
+            "comments": [
+                "The second fan in the system has one sensor(single rotor) feedback",
+                "that is only monitored with the `WaterCooled` property is false. The",
+                "sensor is monitored using a 'count' method where a counter is",
+                "incremented each tick the fan deviates 15% from a target and",
+                "decrements back to zero each tick the fan is within spec. When the",
+                "sensor reaches the threshold of 25 ticks, the fan is marked",
+                "nonfunctional and only returns to being functional when the counter",
+                "is decremented back to 0. This differs from the default 'timebased'",
+                "method where the fan must deviate contiguously for a set amount of",
+                "time to be marked nonfunctional. It takes 1 sensor to mark this fan",
+                "nonfunctional.",
+                "Each sensor has an error logged after 0 seconds being marked",
+                "nonfunctional and the fan has an error logged if its been not present",
+                "for 20 seconds.",
+                "In addition, this fan is not monitored for the first 30 seconds after",
+                "a poweron to allow the fan to spin-up."
+            ],
+            "inventory": "/system/chassis/motherboard/fan1",
+            "method": "count",
+            "deviation": 15,
+            "num_sensors_nonfunc_for_fan_nonfunc": 1,
+            "monitor_start_delay": 30,
+            "fan_missing_error_delay": 20,
+            "nonfunc_rotor_error_delay": 0,
+            "sensors": [
+                {
+                    "name": "fan1_0",
+                    "has_target": true,
+                    "threshold": 25
+                }
+            ],
+            "condition": {
+                "name": "propertiesMatch",
+                "properties": [
+                    {
+                        "object": "/xyz/openbmc_project/inventory/system/chassis",
+                        "interface": "xyz.openbmc_project.Inventory.Decorator.CoolingType",
+                        "property": {
+                            "name": "WaterCooled",
+                            "type": "bool",
+                            "value": false
+                        }
+                    }
+                ]
             }
-          }
-        ]
-      }
-    },
-    {
-      "comments": [
-        "The third fan in the system that has one sensor(single rotor)",
-        "feedback using the default 'timebased' method that allows it to",
-        "deviate from any given target by 15% for up-to 30 seconds before",
-        "being marked nonfunctional in inventory. Instead of using the default",
-        "'xyz.openbmc_project.Control.FanSpeed' target interface, the sensor",
-        "uses the 'xyz.openbmc_project.Control.FanPwm' target interface and",
-        "applies a factor of 21 and offset of 1600 to accomodate the",
-        "difference in target PWM versus the RPM feedback of the sensor to",
-        "determine if the fan sensor is nonfunctional or not. It takes 1",
-        "sensor to mark this fan nonfunctional and when marked nonfunctional,",
-        "it is immediately marked functional again once within 15% of the",
-        "target.",
-        "Each sensor has an error logged after 0 seconds being marked",
-        "nonfunctional and the fan has an error logged if its been not present",
-        "for 20 seconds.",
-        "In addition, this fan is not monitored for the first 30 seconds after",
-        "a poweron to allow the fan to spin-up. "
-      ],
-      "inventory": "/system/chassis/motherboard/fan2",
-      "method": "timebased",
-      "allowed_out_of_range_time": 30,
-      "deviation": 15,
-      "num_sensors_nonfunc_for_fan_nonfunc": 1,
-      "monitor_start_delay": 30,
-      "fan_missing_error_delay": 20,
-      "nonfunc_rotor_error_delay": 0,
-      "sensors": [
-        {
-          "name": "fan2_0",
-          "target_interface": "xyz.openbmc_project.Control.FanPwm",
-          "has_target": true,
-          "factor": 21,
-          "offset": 1600
-        }
-      ]
-    }
-  ],
-  "sensor_trust_groups": [
-    {
-      "comments": [
-        "OPTIONAL - A section to create `trust groups` consisting of fan tach",
-        "sensors that can be used to trust the tach feedback reading or",
-        "disregard it when determining if the fan is functional or not. Here,",
-        "the fan sensor feedbacks within the group are only trusted when any",
-        "one of them shows a non-zero feedback speed. At any time all fan",
-        "sensor feedbacks report a speed of 0, the monitoring of each sensor",
-        "in the group is cancelled, only to resume being monitored when any",
-        "one of them reports a non-zero feedback speed."
-      ],
-      "class": "NonzeroSpeed",
-      "group": [
-        {
-          "name": "fan0_0"
         },
         {
-          "name": "fan1_0"
-        },
-        {
-          "name": "fan2_0"
+            "comments": [
+                "The third fan in the system that has one sensor(single rotor)",
+                "feedback using the default 'timebased' method that allows it to",
+                "deviate from any given target by 15% for up-to 30 seconds before",
+                "being marked nonfunctional in inventory. Instead of using the default",
+                "'xyz.openbmc_project.Control.FanSpeed' target interface, the sensor",
+                "uses the 'xyz.openbmc_project.Control.FanPwm' target interface and",
+                "applies a factor of 21 and offset of 1600 to accomodate the",
+                "difference in target PWM versus the RPM feedback of the sensor to",
+                "determine if the fan sensor is nonfunctional or not. It takes 1",
+                "sensor to mark this fan nonfunctional and when marked nonfunctional,",
+                "it is immediately marked functional again once within 15% of the",
+                "target.",
+                "Each sensor has an error logged after 0 seconds being marked",
+                "nonfunctional and the fan has an error logged if its been not present",
+                "for 20 seconds.",
+                "In addition, this fan is not monitored for the first 30 seconds after",
+                "a poweron to allow the fan to spin-up. "
+            ],
+            "inventory": "/system/chassis/motherboard/fan2",
+            "method": "timebased",
+            "allowed_out_of_range_time": 30,
+            "deviation": 15,
+            "num_sensors_nonfunc_for_fan_nonfunc": 1,
+            "monitor_start_delay": 30,
+            "fan_missing_error_delay": 20,
+            "nonfunc_rotor_error_delay": 0,
+            "sensors": [
+                {
+                    "name": "fan2_0",
+                    "target_interface": "xyz.openbmc_project.Control.FanPwm",
+                    "has_target": true,
+                    "factor": 21,
+                    "offset": 1600
+                }
+            ]
         }
-      ]
-    }
-  ],
-  "fault_handling": {
-    "comments": [
-      "OPTIONAL - A section to handle faults caused by missing or",
-      "nonfunctional fans. An error is logged when 1 rotor is nonfunctional",
-      "across all the fans being monitored. The system is immediately hard",
-      "powered off after a poweron is started when 1 fan has been missing for",
-      "25 seconds.",
-      "An EPOW shutdown is issued when 2 or more nonfunctional fan sensors",
-      "exist, which (specific to EPOW) has a service mode delay of 300 seconds",
-      "and then a meltdown delay of 300 seconds."
     ],
-    "num_nonfunc_rotors_before_error": 1,
-    "power_off_config": [
-      {
-        "type": "hard",
-        "cause": "missing_fan_frus",
-        "count": 1,
-        "delay": 25,
-        "state": "at_pgood"
-      },
-      {
-        "type": "epow",
-        "cause": "nonfunc_fan_rotors",
-        "count": 2,
-        "service_mode_delay": 300,
-        "meltdown_delay": 300
-      }
-    ]
-  }
+    "sensor_trust_groups": [
+        {
+            "comments": [
+                "OPTIONAL - A section to create `trust groups` consisting of fan tach",
+                "sensors that can be used to trust the tach feedback reading or",
+                "disregard it when determining if the fan is functional or not. Here,",
+                "the fan sensor feedbacks within the group are only trusted when any",
+                "one of them shows a non-zero feedback speed. At any time all fan",
+                "sensor feedbacks report a speed of 0, the monitoring of each sensor",
+                "in the group is cancelled, only to resume being monitored when any",
+                "one of them reports a non-zero feedback speed."
+            ],
+            "class": "NonzeroSpeed",
+            "group": [
+                {
+                    "name": "fan0_0"
+                },
+                {
+                    "name": "fan1_0"
+                },
+                {
+                    "name": "fan2_0"
+                }
+            ]
+        }
+    ],
+    "fault_handling": {
+        "comments": [
+            "OPTIONAL - A section to handle faults caused by missing or",
+            "nonfunctional fans. An error is logged when 1 rotor is nonfunctional",
+            "across all the fans being monitored. The system is immediately hard",
+            "powered off after a poweron is started when 1 fan has been missing for",
+            "25 seconds.",
+            "An EPOW shutdown is issued when 2 or more nonfunctional fan sensors",
+            "exist, which (specific to EPOW) has a service mode delay of 300 seconds",
+            "and then a meltdown delay of 300 seconds."
+        ],
+        "num_nonfunc_rotors_before_error": 1,
+        "power_off_config": [
+            {
+                "type": "hard",
+                "cause": "missing_fan_frus",
+                "count": 1,
+                "delay": 25,
+                "state": "at_pgood"
+            },
+            {
+                "type": "epow",
+                "cause": "nonfunc_fan_rotors",
+                "count": 2,
+                "service_mode_delay": 300,
+                "meltdown_delay": 300
+            }
+        ]
+    }
 }