commit | ebe456fcd7c36dd3c9c3cb11b0ee4d54ec42b053 | [log] [tgz] |
---|---|---|
author | Patrick Venture <venture@google.com> | Thu May 30 16:40:39 2019 -0700 |
committer | Patrick Venture <venture@google.com> | Thu May 30 16:40:39 2019 -0700 |
tree | 071ed91f1f42ad26d671c7bdc0ccf3c6482e81ef | |
parent | 4e2fdcd599d2450e598fe6a8fc1562aadb571c19 [diff] |
test: firmware updatePending: read(session) Signed-off-by: Patrick Venture <venture@google.com> Change-Id: Ie0fea7065d2ea93f6d679293452df8c315844b7a
This document describes the OpenBmc software implementing the secure flash update mechanism.
The primary details are here.
This supports two methods of providing the image to stage. You can send the file over IPMI packets, which is a very slow process. A 32-MiB image can take ~3 hours to send via this method. This can be done in <1 minutes via the PCI bridge, or just a few minutes via LPC depending on the size of the mapped area.
This is implemented as a phosphor blob handler.
The image must be signed via the production or development keys, the former being required for production builds. The image itself and the image signature are separately sent to the BMC for verification. The verification package source is beyond the scope of this design.
Basically the IPMI OEM handler receives the image in one fashion or another and then triggers the verify_image
service. Then, the user polls until the result is reported. This is because the image verification process can exceed 10 seconds.
The image flashing mechanism itself is the initramfs stage during reboot. It will check for files named "image-*
" and flash them appropriately for each name to section. The IPMI command creates a file /run/initramfs/bmc-image
and writes the contents there. It was found that writing it in /tmp could cause OOM errors moving it on low memory systems, whereas renaming a file within the same folder seems to only update the directory inode's contents.
The staging file path can be controlled via software configuration. The image is assumed to be the tarball contents and is written into /tmp/{tarball_name}.gz
TODO: Flesh out the UBI approach.
To use phosphor-ipmi-flash
a platform must provide a configuration. A platform can configure multiple interfaces, such as both lpc and pci. However, a platform should only configure either static layout updates, or ubi. If enabling lpc, the platform must specify either aspeed or nuvoton.
The following are the two primary configuration options, which control how the update is treated.
Option | Meaning |
---|---|
--enable-static-layout | Enable treating the update as a static layout update. |
--enable-tarball-ubi | Enable treating the update as a tarball for UBI update. |
The following are configuration options for how the host and BMC are meant to transfer the data. By default, the data-in-IPMI mechanism is enabled.
There are two configurable data transport mechanisms, either staging the bytes via the LPC memory region, or the PCI-to-AHB memory region. Because there is only one MAPPED_ADDRESS
variable at present, a platform should only configure one. The platform's device-tree may have the region locked to a specific driver (lpc-aspeed-ctrl), preventing the region from other use.
NOTE: It will likely be possible to configure both in the near future.
Variable | Default | Meaning |
---|---|---|
MAPPED_ADDRESS | 0 | The address used for mapping P2A or LPC into the BMC's memory-space. |
Option | Meaning |
---|---|
--enable-pci-bridge | Enable the PCI-to-AHB transport option. |
--enable-lpc-bridge | Enable the LPC-to-AHB transport option. |
If a platform enables p2a as the transport mechanism, a specific vendor must be selected via the following configuration option. Currently, only one is supported.
Option | Meaning |
---|---|
--enable-aspeed-p2a | Use with ASPEED parts. |
If a platform enables lpc as the transport mechanism, a specific vendor must be selected via the following configuration option. Currently, only two are supported.
Option | Meaning |
---|---|
--enable-aspeed-lpc | Use with ASPEED parts. |
--enable-nuvoton-lpc | Use with Nuvoton parts. |
The following variables can be set to whatever you wish, however they have usable default values.
Variable | Default | Meaning |
---|---|---|
STATIC_HANDLER_STAGED_NAME | /run/initramfs/bmc-image | The filename where to write the staged firmware image for static updates. |
TARBALL_STAGED_NAME | /tmp/image-update.tar | The filename where to write the UBI update tarball. |
HASH_FILENAME | /tmp/bmc.sig | The file to use for the hash provided. |
VERIFY_STATUS_FILENAME | /tmp/bmc.verify | The file checked for the verification status. |
VERIFY_DBUS_SERVICE | verify_image.service | The systemd service started for verification. |
UPDATE_DBUS_SERVICE | update-bmc.service | The systemd service started for updating the BMC. |