| commit | c73dce91dcfe82ef07b3833af2124be2f5303af5 | [log] [tgz] |
|---|---|---|
| author | Patrick Venture <venture@google.com> | Tue May 07 11:32:44 2019 -0700 |
| committer | Patrick Venture <venture@google.com> | Tue May 07 11:42:03 2019 -0700 |
| tree | 152c7eaee65987d5904e15a47d74976565e2464d | |
| parent | 36bb4670546dfab9e14bc01738aed7d0eac8f324 [diff] |
tools: p2a: read the PCI configuration Read the PCI configuration from the blob handler itself. Don't use this yet, but read it. Tested: Verified with a bugfix in ipmi-blob-tool that it was able to read back and print the value configured into the BMC image. Signed-off-by: Patrick Venture <venture@google.com> Change-Id: I49a8c93508e64a65fd37b50ec2b437f0016272f2
This document describes the OpenBmc software implementing the secure flash update mechanism.
The primary details are here.
This supports two methods of providing the image to stage. You can send the file over IPMI packets, which is a very slow process. A 32-MiB image can take ~3 hours to send via this method. This can be done in <1 minutes via the PCI bridge, or just a few minutes via LPC depending on the size of the mapped area.
This is implemented as a phosphor blob handler.
The image must be signed via the production or development keys, the former being required for production builds. The image itself and the image signature are separately sent to the BMC for verification. The verification package source is beyond the scope of this design.
Basically the IPMI OEM handler receives the image in one fashion or another and then triggers the verify_image service. Then, the user polls until the result is reported. This is because the image verification process can exceed 10 seconds.
The image flashing mechanism itself is the initramfs stage during reboot. It will check for files named "image-*" and flash them appropriately for each name to section. The IPMI command creates a file /run/initramfs/bmc-image and writes the contents there. It was found that writing it in /tmp could cause OOM errors moving it on low memory systems, whereas renaming a file within the same folder seems to only update the directory inode's contents.
The staging file path can be controlled via software configuration. The image is assumed to be the tarball contents and is written into /tmp/{tarball_name}.gz
TODO: Flesh out the UBI approach.
The PCI-to-AHB bridge is only available on some systems, and provides a 64-KiB region that can be pointed anywhere in BMC memory space.
It is controlled by two PCIe MMIO addresses that are based on BAR1. Further specifics can be found in the ASPEED data sheet. However, the way it works in this instance is that the BMC has configured a region of physical memory it plans to use as this buffer region. The BMC returns the address to host program so it can configure the PCIe MMIO registers properly for that address.
As an example, a 64-KiB region a platform can use for this approach is the last 64-KiB of the VGA reserved region: 0x47ff0000.
Like the P2A mechanism, the BMC must have already allocated a memory region with a platform-defined size. This region is mapped to LPC space at the request of the host, which also specifies the LPC address and region size in the mapping request subcommand. The host can then read the actual LPC address at which the BMC was able to map, checking that it's usable.
Note: Not yet implemented for Stat metadata The command will return 1 byte in the response body with value:
After a success map to LPC space, the host can use FlashRequestRegion to read the LPC address of the chunk mapped, which should match that requested.
As future work, USB should be considered an option for staging the image to be copied to the BMC.