prettier: re-format
Prettier is enabled in openbmc-build-scripts on Markdown, JSON, and YAML
files to have consistent formatting for these file types. Re-run the
formatter on the whole repository.
Change-Id: I53dc3bb17d5dcbb9b33fa3d0db62138f37cc8c0b
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
diff --git a/phosphor-regulators/config_files/ibm_bonnell.json b/phosphor-regulators/config_files/ibm_bonnell.json
index 3d6a561..4bf42a1 100644
--- a/phosphor-regulators/config_files/ibm_bonnell.json
+++ b/phosphor-regulators/config_files/ibm_bonnell.json
@@ -1,94 +1,105 @@
{
- "comments": [ "phosphor-regulators configuration file for IBM Bonnell systems" ],
+ "comments": [
+ "phosphor-regulators configuration file for IBM Bonnell systems"
+ ],
-
- "rules": [
- {
- "comments": [ "Rule to set PMBus PAGE to 0" ],
- "id": "set_page0_rule",
- "actions": [
- { "i2c_write_byte": { "register": "0x00", "value": "0x00" } }
- ]
- },
-
-
- {
- "comments": [ "Rule to set PMBus PAGE to 1" ],
- "id": "set_page1_rule",
- "actions": [
- { "i2c_write_byte": { "register": "0x00", "value": "0x01" } }
- ]
- },
-
-
- {
- "comments": [ "Rule to set output voltage of a PMBus regulator" ],
- "id": "set_voltage_rule",
- "actions": [
+ "rules": [
{
- "comments": [ "Write volts value to VOUT_COMMAND in linear format.",
+ "comments": ["Rule to set PMBus PAGE to 0"],
+ "id": "set_page0_rule",
+ "actions": [
+ { "i2c_write_byte": { "register": "0x00", "value": "0x00" } }
+ ]
+ },
+
+ {
+ "comments": ["Rule to set PMBus PAGE to 1"],
+ "id": "set_page1_rule",
+ "actions": [
+ { "i2c_write_byte": { "register": "0x00", "value": "0x01" } }
+ ]
+ },
+
+ {
+ "comments": ["Rule to set output voltage of a PMBus regulator"],
+ "id": "set_voltage_rule",
+ "actions": [
+ {
+ "comments": [
+ "Write volts value to VOUT_COMMAND in linear format.",
"Get volts value from configuration. Get exponent",
- "from VOUT_MODE. Verify write was successful." ],
- "pmbus_write_vout_command": { "format": "linear", "is_verified": true }
- }
- ]
- },
-
-
- {
- "comments": [ "Rule to set output voltage of PAGE 0 of a PMBus regulator" ],
- "id": "set_voltage_page0_rule",
- "actions": [
- { "run_rule": "set_page0_rule" },
- { "run_rule": "set_voltage_rule" }
- ]
- },
-
-
- {
- "comments": [ "Rule to set output voltage of PAGE 1 of a PMBus regulator" ],
- "id": "set_voltage_page1_rule",
- "actions": [
- { "run_rule": "set_page1_rule" },
- { "run_rule": "set_voltage_rule" }
- ]
- },
-
-
- {
- "comments": [ "Rule to set output voltage of a PMBus regulator using",
- "PMBus OPERATION and VOUT_COMMAND" ],
- "id": "set_operation_and_voltage_rule",
- "actions": [
- {
- "comments": [ "Set PMBus OPERATION to 0x80 indicating output voltage",
- "is set by the PMBus VOUT_COMMAND" ],
- "i2c_write_byte": { "register": "0x01", "value": "0x80" }
+ "from VOUT_MODE. Verify write was successful."
+ ],
+ "pmbus_write_vout_command": {
+ "format": "linear",
+ "is_verified": true
+ }
+ }
+ ]
},
{
- "comments": [ "Set the output voltage using the PMBus VOUT_COMMAND" ],
- "run_rule": "set_voltage_rule"
+ "comments": [
+ "Rule to set output voltage of PAGE 0 of a PMBus regulator"
+ ],
+ "id": "set_voltage_page0_rule",
+ "actions": [
+ { "run_rule": "set_page0_rule" },
+ { "run_rule": "set_voltage_rule" }
+ ]
},
{
- "comments": [ "Set PMBus OPERATION to 0xB0 indicating output voltage",
+ "comments": [
+ "Rule to set output voltage of PAGE 1 of a PMBus regulator"
+ ],
+ "id": "set_voltage_page1_rule",
+ "actions": [
+ { "run_rule": "set_page1_rule" },
+ { "run_rule": "set_voltage_rule" }
+ ]
+ },
+
+ {
+ "comments": [
+ "Rule to set output voltage of a PMBus regulator using",
+ "PMBus OPERATION and VOUT_COMMAND"
+ ],
+ "id": "set_operation_and_voltage_rule",
+ "actions": [
+ {
+ "comments": [
+ "Set PMBus OPERATION to 0x80 indicating output voltage",
+ "is set by the PMBus VOUT_COMMAND"
+ ],
+ "i2c_write_byte": { "register": "0x01", "value": "0x80" }
+ },
+
+ {
+ "comments": [
+ "Set the output voltage using the PMBus VOUT_COMMAND"
+ ],
+ "run_rule": "set_voltage_rule"
+ },
+
+ {
+ "comments": [
+ "Set PMBus OPERATION to 0xB0 indicating output voltage",
"will now be set by AVSBus (AVS_VOUT_COMMAND).",
"Hardware settings cause the VOUT_COMMAND value to be",
- "the initial voltage value for AVSBus." ],
- "i2c_write_byte": { "register": "0x01", "value": "0xB0" }
+ "the initial voltage value for AVSBus."
+ ],
+ "i2c_write_byte": { "register": "0x01", "value": "0xB0" }
+ }
+ ]
}
- ]
- }
- ],
+ ],
-
- "chassis": [
- {
- "comments": [ "Chassis (drawer) 1",
- "Note: Devices not defined yet" ],
- "number": 1,
- "inventory_path": "system/chassis"
- }
- ]
+ "chassis": [
+ {
+ "comments": ["Chassis (drawer) 1", "Note: Devices not defined yet"],
+ "number": 1,
+ "inventory_path": "system/chassis"
+ }
+ ]
}
diff --git a/phosphor-regulators/config_files/ibm_everest.json b/phosphor-regulators/config_files/ibm_everest.json
index 014815a..545d910 100644
--- a/phosphor-regulators/config_files/ibm_everest.json
+++ b/phosphor-regulators/config_files/ibm_everest.json
@@ -1,94 +1,105 @@
{
- "comments": [ "phosphor-regulators configuration file for IBM Everest systems" ],
+ "comments": [
+ "phosphor-regulators configuration file for IBM Everest systems"
+ ],
-
- "rules": [
- {
- "comments": [ "Rule to set PMBus PAGE to 0" ],
- "id": "set_page0_rule",
- "actions": [
- { "i2c_write_byte": { "register": "0x00", "value": "0x00" } }
- ]
- },
-
-
- {
- "comments": [ "Rule to set PMBus PAGE to 1" ],
- "id": "set_page1_rule",
- "actions": [
- { "i2c_write_byte": { "register": "0x00", "value": "0x01" } }
- ]
- },
-
-
- {
- "comments": [ "Rule to set output voltage of a PMBus regulator" ],
- "id": "set_voltage_rule",
- "actions": [
+ "rules": [
{
- "comments": [ "Write volts value to VOUT_COMMAND in linear format.",
+ "comments": ["Rule to set PMBus PAGE to 0"],
+ "id": "set_page0_rule",
+ "actions": [
+ { "i2c_write_byte": { "register": "0x00", "value": "0x00" } }
+ ]
+ },
+
+ {
+ "comments": ["Rule to set PMBus PAGE to 1"],
+ "id": "set_page1_rule",
+ "actions": [
+ { "i2c_write_byte": { "register": "0x00", "value": "0x01" } }
+ ]
+ },
+
+ {
+ "comments": ["Rule to set output voltage of a PMBus regulator"],
+ "id": "set_voltage_rule",
+ "actions": [
+ {
+ "comments": [
+ "Write volts value to VOUT_COMMAND in linear format.",
"Get volts value from configuration. Get exponent",
- "from VOUT_MODE. Verify write was successful." ],
- "pmbus_write_vout_command": { "format": "linear", "is_verified": true }
- }
- ]
- },
-
-
- {
- "comments": [ "Rule to set output voltage of PAGE 0 of a PMBus regulator" ],
- "id": "set_voltage_page0_rule",
- "actions": [
- { "run_rule": "set_page0_rule" },
- { "run_rule": "set_voltage_rule" }
- ]
- },
-
-
- {
- "comments": [ "Rule to set output voltage of PAGE 1 of a PMBus regulator" ],
- "id": "set_voltage_page1_rule",
- "actions": [
- { "run_rule": "set_page1_rule" },
- { "run_rule": "set_voltage_rule" }
- ]
- },
-
-
- {
- "comments": [ "Rule to set output voltage of a PMBus regulator using",
- "PMBus OPERATION and VOUT_COMMAND" ],
- "id": "set_operation_and_voltage_rule",
- "actions": [
- {
- "comments": [ "Set PMBus OPERATION to 0x80 indicating output voltage",
- "is set by the PMBus VOUT_COMMAND" ],
- "i2c_write_byte": { "register": "0x01", "value": "0x80" }
+ "from VOUT_MODE. Verify write was successful."
+ ],
+ "pmbus_write_vout_command": {
+ "format": "linear",
+ "is_verified": true
+ }
+ }
+ ]
},
{
- "comments": [ "Set the output voltage using the PMBus VOUT_COMMAND" ],
- "run_rule": "set_voltage_rule"
+ "comments": [
+ "Rule to set output voltage of PAGE 0 of a PMBus regulator"
+ ],
+ "id": "set_voltage_page0_rule",
+ "actions": [
+ { "run_rule": "set_page0_rule" },
+ { "run_rule": "set_voltage_rule" }
+ ]
},
{
- "comments": [ "Set PMBus OPERATION to 0xB0 indicating output voltage",
+ "comments": [
+ "Rule to set output voltage of PAGE 1 of a PMBus regulator"
+ ],
+ "id": "set_voltage_page1_rule",
+ "actions": [
+ { "run_rule": "set_page1_rule" },
+ { "run_rule": "set_voltage_rule" }
+ ]
+ },
+
+ {
+ "comments": [
+ "Rule to set output voltage of a PMBus regulator using",
+ "PMBus OPERATION and VOUT_COMMAND"
+ ],
+ "id": "set_operation_and_voltage_rule",
+ "actions": [
+ {
+ "comments": [
+ "Set PMBus OPERATION to 0x80 indicating output voltage",
+ "is set by the PMBus VOUT_COMMAND"
+ ],
+ "i2c_write_byte": { "register": "0x01", "value": "0x80" }
+ },
+
+ {
+ "comments": [
+ "Set the output voltage using the PMBus VOUT_COMMAND"
+ ],
+ "run_rule": "set_voltage_rule"
+ },
+
+ {
+ "comments": [
+ "Set PMBus OPERATION to 0xB0 indicating output voltage",
"will now be set by AVSBus (AVS_VOUT_COMMAND).",
"Hardware settings cause the VOUT_COMMAND value to be",
- "the initial voltage value for AVSBus." ],
- "i2c_write_byte": { "register": "0x01", "value": "0xB0" }
+ "the initial voltage value for AVSBus."
+ ],
+ "i2c_write_byte": { "register": "0x01", "value": "0xB0" }
+ }
+ ]
}
- ]
- }
- ],
+ ],
-
- "chassis": [
- {
- "comments": [ "Chassis (drawer) 1",
- "Note: Devices not defined yet" ],
- "number": 1,
- "inventory_path": "system/chassis"
- }
- ]
+ "chassis": [
+ {
+ "comments": ["Chassis (drawer) 1", "Note: Devices not defined yet"],
+ "number": 1,
+ "inventory_path": "system/chassis"
+ }
+ ]
}
diff --git a/phosphor-regulators/config_files/ibm_rainier.json b/phosphor-regulators/config_files/ibm_rainier.json
index 8b372e7..09c005f 100644
--- a/phosphor-regulators/config_files/ibm_rainier.json
+++ b/phosphor-regulators/config_files/ibm_rainier.json
@@ -1,1135 +1,1429 @@
{
- "comments": [ "phosphor-regulators configuration file for IBM Rainier systems" ],
+ "comments": [
+ "phosphor-regulators configuration file for IBM Rainier systems"
+ ],
-
- "rules": [
- {
- "comments": [ "Rule to set PMBus PAGE to 0" ],
- "id": "set_page0_rule",
- "actions": [
- { "i2c_write_byte": { "register": "0x00", "value": "0x00" } }
- ]
- },
-
-
- {
- "comments": [ "Rule to set PMBus PAGE to 1" ],
- "id": "set_page1_rule",
- "actions": [
- { "i2c_write_byte": { "register": "0x00", "value": "0x01" } }
- ]
- },
-
-
- {
- "comments": [ "Rule to set output voltage of a PMBus regulator" ],
- "id": "set_voltage_rule",
- "actions": [
+ "rules": [
{
- "comments": [ "Write volts value to VOUT_COMMAND in linear format.",
+ "comments": ["Rule to set PMBus PAGE to 0"],
+ "id": "set_page0_rule",
+ "actions": [
+ { "i2c_write_byte": { "register": "0x00", "value": "0x00" } }
+ ]
+ },
+
+ {
+ "comments": ["Rule to set PMBus PAGE to 1"],
+ "id": "set_page1_rule",
+ "actions": [
+ { "i2c_write_byte": { "register": "0x00", "value": "0x01" } }
+ ]
+ },
+
+ {
+ "comments": ["Rule to set output voltage of a PMBus regulator"],
+ "id": "set_voltage_rule",
+ "actions": [
+ {
+ "comments": [
+ "Write volts value to VOUT_COMMAND in linear format.",
"Get volts value from configuration. Get exponent",
- "from VOUT_MODE. Verify write was successful." ],
- "pmbus_write_vout_command": { "format": "linear", "is_verified": true }
- }
- ]
- },
-
-
- {
- "comments": [ "Rule to set output voltage of PAGE 0 of a PMBus regulator" ],
- "id": "set_voltage_page0_rule",
- "actions": [
- { "run_rule": "set_page0_rule" },
- { "run_rule": "set_voltage_rule" }
- ]
- },
-
-
- {
- "comments": [ "Rule to set output voltage of PAGE 1 of a PMBus regulator" ],
- "id": "set_voltage_page1_rule",
- "actions": [
- { "run_rule": "set_page1_rule" },
- { "run_rule": "set_voltage_rule" }
- ]
- },
-
-
- {
- "comments": [ "Rule to set output voltage of a PMBus regulator using",
- "PMBus OPERATION and VOUT_COMMAND" ],
- "id": "set_operation_and_voltage_rule",
- "actions": [
- {
- "comments": [ "Set PMBus OPERATION to 0x80 indicating output voltage",
- "is set by the PMBus VOUT_COMMAND" ],
- "i2c_write_byte": { "register": "0x01", "value": "0x80" }
+ "from VOUT_MODE. Verify write was successful."
+ ],
+ "pmbus_write_vout_command": {
+ "format": "linear",
+ "is_verified": true
+ }
+ }
+ ]
},
{
- "comments": [ "Set the output voltage using the PMBus VOUT_COMMAND" ],
- "run_rule": "set_voltage_rule"
+ "comments": [
+ "Rule to set output voltage of PAGE 0 of a PMBus regulator"
+ ],
+ "id": "set_voltage_page0_rule",
+ "actions": [
+ { "run_rule": "set_page0_rule" },
+ { "run_rule": "set_voltage_rule" }
+ ]
},
{
- "comments": [ "Set PMBus OPERATION to 0xB0 indicating output voltage",
+ "comments": [
+ "Rule to set output voltage of PAGE 1 of a PMBus regulator"
+ ],
+ "id": "set_voltage_page1_rule",
+ "actions": [
+ { "run_rule": "set_page1_rule" },
+ { "run_rule": "set_voltage_rule" }
+ ]
+ },
+
+ {
+ "comments": [
+ "Rule to set output voltage of a PMBus regulator using",
+ "PMBus OPERATION and VOUT_COMMAND"
+ ],
+ "id": "set_operation_and_voltage_rule",
+ "actions": [
+ {
+ "comments": [
+ "Set PMBus OPERATION to 0x80 indicating output voltage",
+ "is set by the PMBus VOUT_COMMAND"
+ ],
+ "i2c_write_byte": { "register": "0x01", "value": "0x80" }
+ },
+
+ {
+ "comments": [
+ "Set the output voltage using the PMBus VOUT_COMMAND"
+ ],
+ "run_rule": "set_voltage_rule"
+ },
+
+ {
+ "comments": [
+ "Set PMBus OPERATION to 0xB0 indicating output voltage",
"will now be set by AVSBus (AVS_VOUT_COMMAND).",
"Hardware settings cause the VOUT_COMMAND value to be",
- "the initial voltage value for AVSBus." ],
- "i2c_write_byte": { "register": "0x01", "value": "0xB0" }
- }
- ]
- },
+ "the initial voltage value for AVSBus."
+ ],
+ "i2c_write_byte": { "register": "0x01", "value": "0xB0" }
+ }
+ ]
+ },
-
- {
- "comments": [ "Rule to set IOUT_OC_WARN_LIMIT for a PMBus regulator" ],
- "id": "set_iout_oc_warn_limit_rule",
- "actions": [
{
- "comments": [ "Set PMBus IOUT_OC_WARN_LIMIT to 326A to ensure OCW",
+ "comments": [
+ "Rule to set IOUT_OC_WARN_LIMIT for a PMBus regulator"
+ ],
+ "id": "set_iout_oc_warn_limit_rule",
+ "actions": [
+ {
+ "comments": [
+ "Set PMBus IOUT_OC_WARN_LIMIT to 326A to ensure OCW",
"asserts at the roll-over bug identified in the",
"silicon. 326A = 0x08A3. PMBus requires",
- "the low order byte to be written first." ],
- "i2c_write_bytes": { "register": "0x4A", "values": [ "0xA3", "0x08" ] }
- }
- ]
- },
-
-
- {
- "comments": [ "Rule to configure a VDD rail using the PMBus interface" ],
- "id": "configure_vdd_rule",
- "actions": [
- { "run_rule": "set_page0_rule" },
- { "run_rule": "set_iout_oc_warn_limit_rule" },
- {
- "comments": [ "Set VOUT_MODE to exponent of -9 for VDD regulator",
- "to support older and newer hardware." ],
- "i2c_write_byte": { "register": "0x20", "value": "0x17" }
- },
- { "run_rule": "set_operation_and_voltage_rule" },
- {
- "comments": [ "Set VOUT_MIN to 0V since for VDD the voltage",
- "can go down to 0.5V so we want to lower this",
- "limit below 0.5V so the regulator does not trip." ],
- "i2c_write_bytes": { "register": "0x2B", "values": [ "0x00", "0x00" ] }
- },
- {
- "comments": [ "Set VOUT_MAX to 1.255V since for VDD the voltage",
- "can go up to 1.1V so we want to raise this",
- "limit above 1.1V so the regulator does not trip." ],
- "i2c_write_bytes": { "register": "0x24", "values": [ "0x83", "0x02" ] }
- },
- {
- "comments": [ "Set POWER_GOOD_ON for VDD to a value of 0.5V." ],
- "i2c_write_bytes": { "register": "0x5E", "values": [ "0x00", "0x01" ] }
- },
- {
- "comments": [ "Set POWER_GOOD_OFF for VDD to a value of 0.4V." ],
- "i2c_write_bytes": { "register": "0x5F", "values": [ "0xCD", "0x00" ] }
- },
- {
- "comments": [ "Set VOUT_OV_WARN_LIMIT for VDD to a value of 1.30V." ],
- "i2c_write_bytes": { "register": "0x42", "values": [ "0x9A", "0x02" ] }
- },
- {
- "comments": [ "Set VOUT_UV_WARN_LIMIT for VDD to a value of 0.45V." ],
- "i2c_write_bytes": { "register": "0x43", "values": [ "0xE6", "0x00" ] }
- },
- {
- "comments": [ "Set TOFF_FALL time for VDD to a value of 10ms." ],
- "i2c_write_bytes": { "register": "0x65", "values": [ "0x28", "0xF0" ] }
- },
- {
- "comments": [ "Set IOUT_OC_FAULT_RESPONSE for VDD to shutdown." ],
- "i2c_write_byte": { "register": "0x47", "value": "0xC0" }
- }
- ]
- },
-
-
- {
- "comments": [ "Rule to configure a VDN rail using the PMBus interface" ],
- "id": "configure_vdn_rule",
- "actions": [
- { "run_rule": "set_page0_rule" },
- { "run_rule": "set_operation_and_voltage_rule" },
- {
- "comments": [ "Set VOUT_MIN to 0V since for VDN the voltage",
- "can go down to 0.6V so we want to lower this",
- "limit below 0.6V so the regulator does not trip." ],
- "i2c_write_bytes": { "register": "0x2B", "values": [ "0x00", "0x00" ] }
- },
- {
- "comments": [ "Set VOUT_MAX to 1.1V since for VDN the voltage",
- "can go up to 1.0V so we want to raise this",
- "limit above 1.0V so the regulator does not trip." ],
- "i2c_write_bytes": { "register": "0x24", "values": [ "0x33", "0x02" ] }
- },
- {
- "comments": [ "Set POWER_GOOD_ON for VDN to a value of 0.45V." ],
- "i2c_write_bytes": { "register": "0x5E", "values": [ "0xE6", "0x00" ] }
- },
- {
- "comments": [ "Set POWER_GOOD_OFF for VDN to a value of 0.40V." ],
- "i2c_write_bytes": { "register": "0x5F", "values": [ "0xCC", "0x00" ] }
- }
- ]
- },
-
-
- {
- "comments": [ "Rule to configure a VCS rail using the PMBus interface" ],
- "id": "configure_vcs_rule",
- "actions": [
- { "run_rule": "set_page1_rule" },
- { "run_rule": "set_operation_and_voltage_rule" },
- {
- "comments": [ "Set VOUT_MIN to 0V since for VCS the voltage",
- "can go down to 0.7V so we want to lower this",
- "limit below 0.7V so the regulator does not trip." ],
- "i2c_write_bytes": { "register": "0x2B", "values": [ "0x00", "0x00" ] }
- },
- {
- "comments": [ "Set VOUT_MAX to 1.2V since for VCS the voltage",
- "can go up to 1.1V so we want to raise this",
- "limit above 1.1V so the regulator does not trip." ],
- "i2c_write_bytes": { "register": "0x24", "values": [ "0x66", "0x02" ] }
- },
- {
- "comments": [ "Set POWER_GOOD_ON for VCS to a value of 0.55V." ],
- "i2c_write_bytes": { "register": "0x5E", "values": [ "0x19", "0x01" ] }
- },
- {
- "comments": [ "Set POWER_GOOD_OFF for VCS to a value of 0.50V." ],
- "i2c_write_bytes": { "register": "0x5F", "values": [ "0x00", "0x01" ] }
- }
- ]
- },
-
-
- {
- "comments": [ "Rule to configure a VIO rail using the PMBus interface" ],
- "id": "configure_vio_rule",
- "actions": [
- { "run_rule": "set_page0_rule" },
- { "run_rule": "set_operation_and_voltage_rule" },
- {
- "comments": [ "Set VOUT_MIN to 0V since for VIO the voltage",
- "can go down to 0.8V so we want to lower this",
- "limit below 0.8V so the regulator does not trip." ],
- "i2c_write_bytes": { "register": "0x2B", "values": [ "0x00", "0x00" ] }
- },
- {
- "comments": [ "Set VOUT_MAX to 1.1V since for VIO the voltage",
- "can go up to 1.0V so we want to raise this",
- "limit above 1.0V so the regulator does not trip." ],
- "i2c_write_bytes": { "register": "0x24", "values": [ "0x33", "0x02" ] }
- },
- {
- "comments": [ "Set POWER_GOOD_ON for VIO to a value of 0.55V." ],
- "i2c_write_bytes": { "register": "0x5E", "values": [ "0x19", "0x01" ] }
- },
- {
- "comments": [ "Set POWER_GOOD_OFF for VIO to a value of 0.50V." ],
- "i2c_write_bytes": { "register": "0x5F", "values": [ "0x00", "0x01" ] }
- }
- ]
- },
-
-
- {
- "comments": [ "Rule to configure a VPCIE rail using the PMBus interface" ],
- "id": "configure_vpcie_rule",
- "actions": [
- { "run_rule": "set_page0_rule" },
- { "run_rule": "set_voltage_rule" },
- {
- "comments": [ "Set VOUT_MIN to 0V since for VPCIE the voltage",
- "can go down to 0.81V so we want to lower this",
- "limit below 0.81V so the regulator does not trip." ],
- "i2c_write_bytes": { "register": "0x2B", "values": [ "0x00", "0x00" ] }
- },
- {
- "comments": [ "Set VOUT_MAX to 1.0V since for VPCIE the voltage",
- "can go up to 0.91V so we want to raise this",
- "limit above 0.91V so the regulator does not trip." ],
- "i2c_write_bytes": { "register": "0x24", "values": [ "0x00", "0x02" ] }
- },
- {
- "comments": [ "Set POWER_GOOD_ON for VPCIE to a value of 0.65V." ],
- "i2c_write_bytes": { "register": "0x5E", "values": [ "0x4C", "0x01" ] }
- },
- {
- "comments": [ "Set POWER_GOOD_OFF for VPCIE to a value of 0.60V." ],
- "i2c_write_bytes": { "register": "0x5F", "values": [ "0x33", "0x01" ] }
- }
- ]
- },
-
-
- {
- "comments": [ "Rule to read sensors on IR38064 regulators using the",
- "PMBus interface" ],
- "id": "read_sensors_ir38064_rule",
- "actions": [
- {
- "comments": [ "Read output current from READ_IOUT" ],
- "pmbus_read_sensor": {
- "type": "iout",
- "command": "0x8C",
- "format": "linear_11"
- }
- },
- {
- "comments": [ "Read highest output current from MFR_IOUT_PEAK" ],
- "pmbus_read_sensor": {
- "type": "iout_peak",
- "command": "0xDC",
- "format": "linear_11"
- }
- },
- {
- "comments": [ "Read output power from READ_POUT" ],
- "pmbus_read_sensor": {
- "type": "pout",
- "command": "0x96",
- "format": "linear_11"
- }
- },
- {
- "comments": [ "Read temperature from READ_TEMPERATURE" ],
- "pmbus_read_sensor": {
- "type": "temperature",
- "command": "0x8D",
- "format": "linear_11"
- }
- },
- {
- "comments": [ "Read highest temperature from MFR_TEMPERATURE_PEAK" ],
- "pmbus_read_sensor": {
- "type": "temperature_peak",
- "command": "0xDD",
- "format": "linear_11"
- }
- },
- {
- "comments": [ "Read output voltage from READ_VOUT.",
- "Note: regulator does not support VOUT_MODE, so the",
- "exponent must be specified." ],
- "pmbus_read_sensor": {
- "type": "vout",
- "command": "0x8B",
- "format": "linear_16",
- "exponent": -8
- }
- },
- {
- "comments": [ "Read highest output voltage from MFR_VOUT_PEAK.",
- "Note: regulator does not support VOUT_MODE, so the",
- "exponent must be specified." ],
- "pmbus_read_sensor": {
- "type": "vout_peak",
- "command": "0xDB",
- "format": "linear_16",
- "exponent": -8
- }
- }
- ]
- },
-
-
- {
- "comments": [ "Rule to read sensors on IR35221 regulators using the",
- "PMBus interface" ],
- "id": "read_sensors_ir35221_rule",
- "actions": [
- {
- "comments": [ "Read output current from READ_IOUT" ],
- "pmbus_read_sensor": {
- "type": "iout",
- "command": "0x8C",
- "format": "linear_11"
- }
- },
- {
- "comments": [ "Read highest output current from MFR_IOUT_PEAK" ],
- "pmbus_read_sensor": {
- "type": "iout_peak",
- "command": "0xC7",
- "format": "linear_11"
- }
- },
- {
- "comments": [ "Read lowest output current from MFR_IOUT_VALLEY" ],
- "pmbus_read_sensor": {
- "type": "iout_valley",
- "command": "0xCB",
- "format": "linear_11"
- }
- },
- {
- "comments": [ "Read output power from READ_POUT" ],
- "pmbus_read_sensor": {
- "type": "pout",
- "command": "0x96",
- "format": "linear_11"
- }
- },
- {
- "comments": [ "Read temperature from READ_TEMPERATURE_1" ],
- "pmbus_read_sensor": {
- "type": "temperature",
- "command": "0x8D",
- "format": "linear_11"
- }
- },
- {
- "comments": [ "Read highest temperature from MFR_TEMP_PEAK" ],
- "pmbus_read_sensor": {
- "type": "temperature_peak",
- "command": "0xC8",
- "format": "linear_11"
- }
- },
- {
- "comments": [ "Read output voltage from READ_VOUT" ],
- "pmbus_read_sensor": {
- "type": "vout",
- "command": "0x8B",
- "format": "linear_16"
- }
- },
- {
- "comments": [ "Read highest output voltage from MFR_VOUT_PEAK" ],
- "pmbus_read_sensor": {
- "type": "vout_peak",
- "command": "0xC6",
- "format": "linear_16"
- }
- },
- {
- "comments": [ "Read lowest output voltage from MFR_VOUT_VALLEY" ],
- "pmbus_read_sensor": {
- "type": "vout_valley",
- "command": "0xCA",
- "format": "linear_16"
- }
- }
- ]
- },
-
-
- {
- "comments": [ "Rule to read sensors on PAGE 0 of IR35221 regulators",
- "using the PMBus interface" ],
- "id": "read_sensors_ir35221_page0_rule",
- "actions": [
- { "run_rule": "set_page0_rule" },
- { "run_rule": "read_sensors_ir35221_rule" }
- ]
- },
-
-
- {
- "comments": [ "Rule to read sensors on PAGE 1 of IR35221 regulators",
- "using the PMBus interface" ],
- "id": "read_sensors_ir35221_page1_rule",
- "actions": [
- { "run_rule": "set_page1_rule" },
- { "run_rule": "read_sensors_ir35221_rule" }
- ]
- },
-
-
- {
- "comments": [ "Rule to read sensors on PAGE 0 of XDPE132G5C regulators",
- "using the PMBus interface" ],
- "id": "read_sensors_xdpe132g5c_page0_rule",
- "actions": [
- {
- "comments": [ "Can use same rule as for IR35221 regulators" ],
- "run_rule": "read_sensors_ir35221_page0_rule"
- }
- ]
- },
-
-
- {
- "comments": [ "Rule to determine if the current system is a 2S4U/2S2U.",
- "2S systems have more regulators on the Nisqually system",
- "planar than 1S systems. Must return true if system is a",
- "2S4U/2S2U and false if system is a 1S4U." ],
- "id": "is_2s_system_rule",
- "actions": [
- {
- "comments": [ "Check whether the CCIN VPD keyword on the Nisqually",
- "system planar has the value for 2S4U or 2S2U" ],
- "or": [
- { "compare_vpd": { "fru": "system/chassis/motherboard", "keyword": "CCIN", "value": "2E2F" } },
- { "compare_vpd": { "fru": "system/chassis/motherboard", "keyword": "CCIN", "value": "2E2D" } }
- ]
- }
- ]
- },
-
-
- {
- "comments": [ "Rule to determine if pass 2 or higher Nisqually",
- "backplane is present. Must return true if present and",
- "false otherwise." ],
- "id": "is_pass2_nisqually_rule",
- "actions": [
- {
- "comments": [ "Check that the PartNumber VPD keyword on the",
- "Nisqually system planar is not the value for",
- "the pass 1 2U or 4U." ],
- "not":
- {
- "or": [
- { "compare_vpd": { "fru": "system/chassis/motherboard", "keyword": "PartNumber", "value": "02WG656" } },
- { "compare_vpd": { "fru": "system/chassis/motherboard", "keyword": "PartNumber", "value": "02WG678" } }
+ "the low order byte to be written first."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x4A",
+ "values": ["0xA3", "0x08"]
+ }
+ }
]
- }
- }
- ]
- },
+ },
-
- {
- "comments": [ "Rule to determine if the VRM FRU for DCM-1 is present.",
- "Must return true if VRM is present and false if VRM is",
- "missing." ],
- "id": "is_dcm1_vrm_present_rule",
- "actions": [
{
- "comments": [ "Check whether the VRM FRU is present OR the DCM-1",
+ "comments": [
+ "Rule to configure a VDD rail using the PMBus interface"
+ ],
+ "id": "configure_vdd_rule",
+ "actions": [
+ { "run_rule": "set_page0_rule" },
+ { "run_rule": "set_iout_oc_warn_limit_rule" },
+ {
+ "comments": [
+ "Set VOUT_MODE to exponent of -9 for VDD regulator",
+ "to support older and newer hardware."
+ ],
+ "i2c_write_byte": { "register": "0x20", "value": "0x17" }
+ },
+ { "run_rule": "set_operation_and_voltage_rule" },
+ {
+ "comments": [
+ "Set VOUT_MIN to 0V since for VDD the voltage",
+ "can go down to 0.5V so we want to lower this",
+ "limit below 0.5V so the regulator does not trip."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x2B",
+ "values": ["0x00", "0x00"]
+ }
+ },
+ {
+ "comments": [
+ "Set VOUT_MAX to 1.255V since for VDD the voltage",
+ "can go up to 1.1V so we want to raise this",
+ "limit above 1.1V so the regulator does not trip."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x24",
+ "values": ["0x83", "0x02"]
+ }
+ },
+ {
+ "comments": [
+ "Set POWER_GOOD_ON for VDD to a value of 0.5V."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x5E",
+ "values": ["0x00", "0x01"]
+ }
+ },
+ {
+ "comments": [
+ "Set POWER_GOOD_OFF for VDD to a value of 0.4V."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x5F",
+ "values": ["0xCD", "0x00"]
+ }
+ },
+ {
+ "comments": [
+ "Set VOUT_OV_WARN_LIMIT for VDD to a value of 1.30V."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x42",
+ "values": ["0x9A", "0x02"]
+ }
+ },
+ {
+ "comments": [
+ "Set VOUT_UV_WARN_LIMIT for VDD to a value of 0.45V."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x43",
+ "values": ["0xE6", "0x00"]
+ }
+ },
+ {
+ "comments": [
+ "Set TOFF_FALL time for VDD to a value of 10ms."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x65",
+ "values": ["0x28", "0xF0"]
+ }
+ },
+ {
+ "comments": [
+ "Set IOUT_OC_FAULT_RESPONSE for VDD to shutdown."
+ ],
+ "i2c_write_byte": { "register": "0x47", "value": "0xC0" }
+ }
+ ]
+ },
+
+ {
+ "comments": [
+ "Rule to configure a VDN rail using the PMBus interface"
+ ],
+ "id": "configure_vdn_rule",
+ "actions": [
+ { "run_rule": "set_page0_rule" },
+ { "run_rule": "set_operation_and_voltage_rule" },
+ {
+ "comments": [
+ "Set VOUT_MIN to 0V since for VDN the voltage",
+ "can go down to 0.6V so we want to lower this",
+ "limit below 0.6V so the regulator does not trip."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x2B",
+ "values": ["0x00", "0x00"]
+ }
+ },
+ {
+ "comments": [
+ "Set VOUT_MAX to 1.1V since for VDN the voltage",
+ "can go up to 1.0V so we want to raise this",
+ "limit above 1.0V so the regulator does not trip."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x24",
+ "values": ["0x33", "0x02"]
+ }
+ },
+ {
+ "comments": [
+ "Set POWER_GOOD_ON for VDN to a value of 0.45V."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x5E",
+ "values": ["0xE6", "0x00"]
+ }
+ },
+ {
+ "comments": [
+ "Set POWER_GOOD_OFF for VDN to a value of 0.40V."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x5F",
+ "values": ["0xCC", "0x00"]
+ }
+ }
+ ]
+ },
+
+ {
+ "comments": [
+ "Rule to configure a VCS rail using the PMBus interface"
+ ],
+ "id": "configure_vcs_rule",
+ "actions": [
+ { "run_rule": "set_page1_rule" },
+ { "run_rule": "set_operation_and_voltage_rule" },
+ {
+ "comments": [
+ "Set VOUT_MIN to 0V since for VCS the voltage",
+ "can go down to 0.7V so we want to lower this",
+ "limit below 0.7V so the regulator does not trip."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x2B",
+ "values": ["0x00", "0x00"]
+ }
+ },
+ {
+ "comments": [
+ "Set VOUT_MAX to 1.2V since for VCS the voltage",
+ "can go up to 1.1V so we want to raise this",
+ "limit above 1.1V so the regulator does not trip."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x24",
+ "values": ["0x66", "0x02"]
+ }
+ },
+ {
+ "comments": [
+ "Set POWER_GOOD_ON for VCS to a value of 0.55V."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x5E",
+ "values": ["0x19", "0x01"]
+ }
+ },
+ {
+ "comments": [
+ "Set POWER_GOOD_OFF for VCS to a value of 0.50V."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x5F",
+ "values": ["0x00", "0x01"]
+ }
+ }
+ ]
+ },
+
+ {
+ "comments": [
+ "Rule to configure a VIO rail using the PMBus interface"
+ ],
+ "id": "configure_vio_rule",
+ "actions": [
+ { "run_rule": "set_page0_rule" },
+ { "run_rule": "set_operation_and_voltage_rule" },
+ {
+ "comments": [
+ "Set VOUT_MIN to 0V since for VIO the voltage",
+ "can go down to 0.8V so we want to lower this",
+ "limit below 0.8V so the regulator does not trip."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x2B",
+ "values": ["0x00", "0x00"]
+ }
+ },
+ {
+ "comments": [
+ "Set VOUT_MAX to 1.1V since for VIO the voltage",
+ "can go up to 1.0V so we want to raise this",
+ "limit above 1.0V so the regulator does not trip."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x24",
+ "values": ["0x33", "0x02"]
+ }
+ },
+ {
+ "comments": [
+ "Set POWER_GOOD_ON for VIO to a value of 0.55V."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x5E",
+ "values": ["0x19", "0x01"]
+ }
+ },
+ {
+ "comments": [
+ "Set POWER_GOOD_OFF for VIO to a value of 0.50V."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x5F",
+ "values": ["0x00", "0x01"]
+ }
+ }
+ ]
+ },
+
+ {
+ "comments": [
+ "Rule to configure a VPCIE rail using the PMBus interface"
+ ],
+ "id": "configure_vpcie_rule",
+ "actions": [
+ { "run_rule": "set_page0_rule" },
+ { "run_rule": "set_voltage_rule" },
+ {
+ "comments": [
+ "Set VOUT_MIN to 0V since for VPCIE the voltage",
+ "can go down to 0.81V so we want to lower this",
+ "limit below 0.81V so the regulator does not trip."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x2B",
+ "values": ["0x00", "0x00"]
+ }
+ },
+ {
+ "comments": [
+ "Set VOUT_MAX to 1.0V since for VPCIE the voltage",
+ "can go up to 0.91V so we want to raise this",
+ "limit above 0.91V so the regulator does not trip."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x24",
+ "values": ["0x00", "0x02"]
+ }
+ },
+ {
+ "comments": [
+ "Set POWER_GOOD_ON for VPCIE to a value of 0.65V."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x5E",
+ "values": ["0x4C", "0x01"]
+ }
+ },
+ {
+ "comments": [
+ "Set POWER_GOOD_OFF for VPCIE to a value of 0.60V."
+ ],
+ "i2c_write_bytes": {
+ "register": "0x5F",
+ "values": ["0x33", "0x01"]
+ }
+ }
+ ]
+ },
+
+ {
+ "comments": [
+ "Rule to read sensors on IR38064 regulators using the",
+ "PMBus interface"
+ ],
+ "id": "read_sensors_ir38064_rule",
+ "actions": [
+ {
+ "comments": ["Read output current from READ_IOUT"],
+ "pmbus_read_sensor": {
+ "type": "iout",
+ "command": "0x8C",
+ "format": "linear_11"
+ }
+ },
+ {
+ "comments": [
+ "Read highest output current from MFR_IOUT_PEAK"
+ ],
+ "pmbus_read_sensor": {
+ "type": "iout_peak",
+ "command": "0xDC",
+ "format": "linear_11"
+ }
+ },
+ {
+ "comments": ["Read output power from READ_POUT"],
+ "pmbus_read_sensor": {
+ "type": "pout",
+ "command": "0x96",
+ "format": "linear_11"
+ }
+ },
+ {
+ "comments": ["Read temperature from READ_TEMPERATURE"],
+ "pmbus_read_sensor": {
+ "type": "temperature",
+ "command": "0x8D",
+ "format": "linear_11"
+ }
+ },
+ {
+ "comments": [
+ "Read highest temperature from MFR_TEMPERATURE_PEAK"
+ ],
+ "pmbus_read_sensor": {
+ "type": "temperature_peak",
+ "command": "0xDD",
+ "format": "linear_11"
+ }
+ },
+ {
+ "comments": [
+ "Read output voltage from READ_VOUT.",
+ "Note: regulator does not support VOUT_MODE, so the",
+ "exponent must be specified."
+ ],
+ "pmbus_read_sensor": {
+ "type": "vout",
+ "command": "0x8B",
+ "format": "linear_16",
+ "exponent": -8
+ }
+ },
+ {
+ "comments": [
+ "Read highest output voltage from MFR_VOUT_PEAK.",
+ "Note: regulator does not support VOUT_MODE, so the",
+ "exponent must be specified."
+ ],
+ "pmbus_read_sensor": {
+ "type": "vout_peak",
+ "command": "0xDB",
+ "format": "linear_16",
+ "exponent": -8
+ }
+ }
+ ]
+ },
+
+ {
+ "comments": [
+ "Rule to read sensors on IR35221 regulators using the",
+ "PMBus interface"
+ ],
+ "id": "read_sensors_ir35221_rule",
+ "actions": [
+ {
+ "comments": ["Read output current from READ_IOUT"],
+ "pmbus_read_sensor": {
+ "type": "iout",
+ "command": "0x8C",
+ "format": "linear_11"
+ }
+ },
+ {
+ "comments": [
+ "Read highest output current from MFR_IOUT_PEAK"
+ ],
+ "pmbus_read_sensor": {
+ "type": "iout_peak",
+ "command": "0xC7",
+ "format": "linear_11"
+ }
+ },
+ {
+ "comments": [
+ "Read lowest output current from MFR_IOUT_VALLEY"
+ ],
+ "pmbus_read_sensor": {
+ "type": "iout_valley",
+ "command": "0xCB",
+ "format": "linear_11"
+ }
+ },
+ {
+ "comments": ["Read output power from READ_POUT"],
+ "pmbus_read_sensor": {
+ "type": "pout",
+ "command": "0x96",
+ "format": "linear_11"
+ }
+ },
+ {
+ "comments": ["Read temperature from READ_TEMPERATURE_1"],
+ "pmbus_read_sensor": {
+ "type": "temperature",
+ "command": "0x8D",
+ "format": "linear_11"
+ }
+ },
+ {
+ "comments": ["Read highest temperature from MFR_TEMP_PEAK"],
+ "pmbus_read_sensor": {
+ "type": "temperature_peak",
+ "command": "0xC8",
+ "format": "linear_11"
+ }
+ },
+ {
+ "comments": ["Read output voltage from READ_VOUT"],
+ "pmbus_read_sensor": {
+ "type": "vout",
+ "command": "0x8B",
+ "format": "linear_16"
+ }
+ },
+ {
+ "comments": [
+ "Read highest output voltage from MFR_VOUT_PEAK"
+ ],
+ "pmbus_read_sensor": {
+ "type": "vout_peak",
+ "command": "0xC6",
+ "format": "linear_16"
+ }
+ },
+ {
+ "comments": [
+ "Read lowest output voltage from MFR_VOUT_VALLEY"
+ ],
+ "pmbus_read_sensor": {
+ "type": "vout_valley",
+ "command": "0xCA",
+ "format": "linear_16"
+ }
+ }
+ ]
+ },
+
+ {
+ "comments": [
+ "Rule to read sensors on PAGE 0 of IR35221 regulators",
+ "using the PMBus interface"
+ ],
+ "id": "read_sensors_ir35221_page0_rule",
+ "actions": [
+ { "run_rule": "set_page0_rule" },
+ { "run_rule": "read_sensors_ir35221_rule" }
+ ]
+ },
+
+ {
+ "comments": [
+ "Rule to read sensors on PAGE 1 of IR35221 regulators",
+ "using the PMBus interface"
+ ],
+ "id": "read_sensors_ir35221_page1_rule",
+ "actions": [
+ { "run_rule": "set_page1_rule" },
+ { "run_rule": "read_sensors_ir35221_rule" }
+ ]
+ },
+
+ {
+ "comments": [
+ "Rule to read sensors on PAGE 0 of XDPE132G5C regulators",
+ "using the PMBus interface"
+ ],
+ "id": "read_sensors_xdpe132g5c_page0_rule",
+ "actions": [
+ {
+ "comments": ["Can use same rule as for IR35221 regulators"],
+ "run_rule": "read_sensors_ir35221_page0_rule"
+ }
+ ]
+ },
+
+ {
+ "comments": [
+ "Rule to determine if the current system is a 2S4U/2S2U.",
+ "2S systems have more regulators on the Nisqually system",
+ "planar than 1S systems. Must return true if system is a",
+ "2S4U/2S2U and false if system is a 1S4U."
+ ],
+ "id": "is_2s_system_rule",
+ "actions": [
+ {
+ "comments": [
+ "Check whether the CCIN VPD keyword on the Nisqually",
+ "system planar has the value for 2S4U or 2S2U"
+ ],
+ "or": [
+ {
+ "compare_vpd": {
+ "fru": "system/chassis/motherboard",
+ "keyword": "CCIN",
+ "value": "2E2F"
+ }
+ },
+ {
+ "compare_vpd": {
+ "fru": "system/chassis/motherboard",
+ "keyword": "CCIN",
+ "value": "2E2D"
+ }
+ }
+ ]
+ }
+ ]
+ },
+
+ {
+ "comments": [
+ "Rule to determine if pass 2 or higher Nisqually",
+ "backplane is present. Must return true if present and",
+ "false otherwise."
+ ],
+ "id": "is_pass2_nisqually_rule",
+ "actions": [
+ {
+ "comments": [
+ "Check that the PartNumber VPD keyword on the",
+ "Nisqually system planar is not the value for",
+ "the pass 1 2U or 4U."
+ ],
+ "not": {
+ "or": [
+ {
+ "compare_vpd": {
+ "fru": "system/chassis/motherboard",
+ "keyword": "PartNumber",
+ "value": "02WG656"
+ }
+ },
+ {
+ "compare_vpd": {
+ "fru": "system/chassis/motherboard",
+ "keyword": "PartNumber",
+ "value": "02WG678"
+ }
+ }
+ ]
+ }
+ }
+ ]
+ },
+
+ {
+ "comments": [
+ "Rule to determine if the VRM FRU for DCM-1 is present.",
+ "Must return true if VRM is present and false if VRM is",
+ "missing."
+ ],
+ "id": "is_dcm1_vrm_present_rule",
+ "actions": [
+ {
+ "comments": [
+ "Check whether the VRM FRU is present OR the DCM-1",
"FRU is present. This provides a double check in",
"case the VRM presence line is not working. If DCM-1",
- "is present, the associated VRM should be too." ],
- "or": [
- { "compare_presence": { "fru": "system/chassis/motherboard/vdd_vrm1", "value": true } },
- { "compare_presence": { "fru": "system/chassis/motherboard/dcm1/cpu0", "value": true } }
- ]
- }
- ]
- },
-
-
- {
- "comments": [ "Rule to determine if a Flett card is present in slot C8.",
- "This requires a Nisqually pass2+ due to I2C bus number",
- "differences between pass 1 and pass 2.",
- "Pass 1 and pass 2 Fletts are both supported.",
- "Must return true if present and false otherwise." ],
- "id": "is_flett_c8_present_rule",
- "actions": [
- {
- "if": {
- "condition": {
- "comments": [ "Check if the Nisqually is pass 2" ],
- "run_rule": "is_pass2_nisqually_rule"
- },
- "then": [
- {
- "comments": [ "Check if a card is present in slot C8" ],
- "if": {
- "condition": {
- "compare_presence": {
- "fru": "system/chassis/motherboard/pcieslot8/pcie_card8",
- "value": true
- }
- },
- "then": [
- {
- "comments": [ "Check if card has Flett CCIN keyword" ],
- "compare_vpd": {
- "fru": "system/chassis/motherboard/pcieslot8/pcie_card8",
- "keyword": "CCIN",
- "value": "6B87"
- }
- }
- ]
- }
- }
- ]
- }
- }
- ]
- },
-
-
- {
- "comments": [ "Rule to determine if a Flett card is present in slot C9.",
- "This requires a Nisqually pass2+ due to I2C bus number",
- "differences between pass 1 and pass 2.",
- "This also requires the Flett to be pass 2 because the",
- "pass 1 regulator has a different I2C address.",
- "Must return true if present and false otherwise." ],
- "id": "is_flett_c9_present_rule",
- "actions": [
- {
- "if": {
- "condition": {
- "comments": [ "Check if the Nisqually is pass 2" ],
- "run_rule": "is_pass2_nisqually_rule"
- },
- "then": [
- {
- "comments": [ "Check if a card is present in slot C9" ],
- "if": {
- "condition": {
- "compare_presence": {
- "fru": "system/chassis/motherboard/pcieslot9/pcie_card9",
- "value": true
- }
- },
- "then": [
- {
- "comments": [ "Check if card has Flett CCIN keyword" ],
- "if": {
- "condition": {
- "compare_vpd": {
- "fru": "system/chassis/motherboard/pcieslot9/pcie_card9",
- "keyword": "CCIN",
- "value": "6B87"
- }
- },
- "then": [
- {
- "comments": [
- "Check that card does not have a pass 1",
- "part number"
- ],
- "not": {
- "or": [
- {
- "compare_vpd": {
- "fru": "system/chassis/motherboard/pcieslot9/pcie_card9",
- "keyword": "PartNumber",
- "value": "03FL194"
- }
- },
- {
- "compare_vpd": {
- "fru": "system/chassis/motherboard/pcieslot9/pcie_card9",
- "keyword": "PartNumber",
- "value": "03FL204"
- }
- }
- ]
+ "is present, the associated VRM should be too."
+ ],
+ "or": [
+ {
+ "compare_presence": {
+ "fru": "system/chassis/motherboard/vdd_vrm1",
+ "value": true
}
- }
- ]
- }
- }
- ]
- }
- }
- ]
- }
- }
- ]
- },
-
-
- {
- "comments": [ "Rule to determine if a Flett card is present in slot C10.",
- "This requires a Nisqually pass2+ due to I2C bus number",
- "differences between pass 1 and pass 2.",
- "This also requires the Flett to be pass 2 because the",
- "pass 1 regulator has a different I2C address.",
- "Must return true if present and false otherwise." ],
- "id": "is_flett_c10_present_rule",
- "actions": [
- {
- "if": {
- "condition": {
- "comments": [ "Check if the Nisqually is pass 2" ],
- "run_rule": "is_pass2_nisqually_rule"
- },
- "then": [
- {
- "comments": [ "Check if a card is present in slot C10" ],
- "if": {
- "condition": {
- "compare_presence": {
- "fru": "system/chassis/motherboard/pcieslot10/pcie_card10",
- "value": true
- }
- },
- "then": [
- {
- "comments": [ "Check if card has Flett CCIN keyword" ],
- "if": {
- "condition": {
- "compare_vpd": {
- "fru": "system/chassis/motherboard/pcieslot10/pcie_card10",
- "keyword": "CCIN",
- "value": "6B87"
- }
},
- "then": [
- {
- "comments": [
- "Check that card does not have a pass 1",
- "part number"
- ],
- "not": {
- "or": [
- {
- "compare_vpd": {
- "fru": "system/chassis/motherboard/pcieslot10/pcie_card10",
- "keyword": "PartNumber",
- "value": "03FL194"
- }
- },
- {
- "compare_vpd": {
- "fru": "system/chassis/motherboard/pcieslot10/pcie_card10",
- "keyword": "PartNumber",
- "value": "03FL204"
- }
- }
- ]
+ {
+ "compare_presence": {
+ "fru": "system/chassis/motherboard/dcm1/cpu0",
+ "value": true
}
- }
- ]
- }
- }
- ]
+ }
+ ]
}
- }
]
- }
- }
- ]
- },
-
-
- {
- "comments": [ "Rule to determine if a Flett card is present in slot C11.",
- "This requires a Nisqually pass2+ due to I2C bus number",
- "differences between pass 1 and pass 2.",
- "Pass 1 and pass 2 Fletts are both supported.",
- "Must return true if present and false otherwise." ],
- "id": "is_flett_c11_present_rule",
- "actions": [
- {
- "if": {
- "condition": {
- "comments": [ "Check if the Nisqually is pass 2" ],
- "run_rule": "is_pass2_nisqually_rule"
- },
- "then": [
- {
- "comments": [ "Check if a card is present in slot C11" ],
- "if": {
- "condition": {
- "compare_presence": {
- "fru": "system/chassis/motherboard/pcieslot11/pcie_card11",
- "value": true
- }
- },
- "then": [
- {
- "comments": [ "Check if card has Flett CCIN keyword" ],
- "compare_vpd": {
- "fru": "system/chassis/motherboard/pcieslot11/pcie_card11",
- "keyword": "CCIN",
- "value": "6B87"
- }
- }
- ]
- }
- }
- ]
- }
- }
- ]
- }
- ],
-
-
- "chassis": [
- {
- "comments": [ "Chassis (drawer) 1" ],
- "number": 1,
- "inventory_path": "system/chassis",
- "devices": [
- {
- "comments": [ "AVDD / IR38064: Primary PMBus Interface",
- "In schematic: bus 4 (1-based), address 0xE2 (8-bit)" ],
- "id": "avdd_regulator",
- "is_regulator": true,
- "fru": "system/chassis/motherboard",
- "i2c_interface": { "bus": 3, "address": "0x71" },
- "presence_detection": { "rule_id": "is_pass2_nisqually_rule" },
- "rails": [
- {
- "id": "avdd_rail",
- "sensor_monitoring": { "rule_id": "read_sensors_ir38064_rule" }
- }
- ]
},
+ {
+ "comments": [
+ "Rule to determine if a Flett card is present in slot C8.",
+ "This requires a Nisqually pass2+ due to I2C bus number",
+ "differences between pass 1 and pass 2.",
+ "Pass 1 and pass 2 Fletts are both supported.",
+ "Must return true if present and false otherwise."
+ ],
+ "id": "is_flett_c8_present_rule",
+ "actions": [
+ {
+ "if": {
+ "condition": {
+ "comments": ["Check if the Nisqually is pass 2"],
+ "run_rule": "is_pass2_nisqually_rule"
+ },
+ "then": [
+ {
+ "comments": [
+ "Check if a card is present in slot C8"
+ ],
+ "if": {
+ "condition": {
+ "compare_presence": {
+ "fru": "system/chassis/motherboard/pcieslot8/pcie_card8",
+ "value": true
+ }
+ },
+ "then": [
+ {
+ "comments": [
+ "Check if card has Flett CCIN keyword"
+ ],
+ "compare_vpd": {
+ "fru": "system/chassis/motherboard/pcieslot8/pcie_card8",
+ "keyword": "CCIN",
+ "value": "6B87"
+ }
+ }
+ ]
+ }
+ }
+ ]
+ }
+ }
+ ]
+ },
{
- "comments": [ "3.3VA / TPS549D22",
+ "comments": [
+ "Rule to determine if a Flett card is present in slot C9.",
+ "This requires a Nisqually pass2+ due to I2C bus number",
+ "differences between pass 1 and pass 2.",
+ "This also requires the Flett to be pass 2 because the",
+ "pass 1 regulator has a different I2C address.",
+ "Must return true if present and false otherwise."
+ ],
+ "id": "is_flett_c9_present_rule",
+ "actions": [
+ {
+ "if": {
+ "condition": {
+ "comments": ["Check if the Nisqually is pass 2"],
+ "run_rule": "is_pass2_nisqually_rule"
+ },
+ "then": [
+ {
+ "comments": [
+ "Check if a card is present in slot C9"
+ ],
+ "if": {
+ "condition": {
+ "compare_presence": {
+ "fru": "system/chassis/motherboard/pcieslot9/pcie_card9",
+ "value": true
+ }
+ },
+ "then": [
+ {
+ "comments": [
+ "Check if card has Flett CCIN keyword"
+ ],
+ "if": {
+ "condition": {
+ "compare_vpd": {
+ "fru": "system/chassis/motherboard/pcieslot9/pcie_card9",
+ "keyword": "CCIN",
+ "value": "6B87"
+ }
+ },
+ "then": [
+ {
+ "comments": [
+ "Check that card does not have a pass 1",
+ "part number"
+ ],
+ "not": {
+ "or": [
+ {
+ "compare_vpd": {
+ "fru": "system/chassis/motherboard/pcieslot9/pcie_card9",
+ "keyword": "PartNumber",
+ "value": "03FL194"
+ }
+ },
+ {
+ "compare_vpd": {
+ "fru": "system/chassis/motherboard/pcieslot9/pcie_card9",
+ "keyword": "PartNumber",
+ "value": "03FL204"
+ }
+ }
+ ]
+ }
+ }
+ ]
+ }
+ }
+ ]
+ }
+ }
+ ]
+ }
+ }
+ ]
+ },
+
+ {
+ "comments": [
+ "Rule to determine if a Flett card is present in slot C10.",
+ "This requires a Nisqually pass2+ due to I2C bus number",
+ "differences between pass 1 and pass 2.",
+ "This also requires the Flett to be pass 2 because the",
+ "pass 1 regulator has a different I2C address.",
+ "Must return true if present and false otherwise."
+ ],
+ "id": "is_flett_c10_present_rule",
+ "actions": [
+ {
+ "if": {
+ "condition": {
+ "comments": ["Check if the Nisqually is pass 2"],
+ "run_rule": "is_pass2_nisqually_rule"
+ },
+ "then": [
+ {
+ "comments": [
+ "Check if a card is present in slot C10"
+ ],
+ "if": {
+ "condition": {
+ "compare_presence": {
+ "fru": "system/chassis/motherboard/pcieslot10/pcie_card10",
+ "value": true
+ }
+ },
+ "then": [
+ {
+ "comments": [
+ "Check if card has Flett CCIN keyword"
+ ],
+ "if": {
+ "condition": {
+ "compare_vpd": {
+ "fru": "system/chassis/motherboard/pcieslot10/pcie_card10",
+ "keyword": "CCIN",
+ "value": "6B87"
+ }
+ },
+ "then": [
+ {
+ "comments": [
+ "Check that card does not have a pass 1",
+ "part number"
+ ],
+ "not": {
+ "or": [
+ {
+ "compare_vpd": {
+ "fru": "system/chassis/motherboard/pcieslot10/pcie_card10",
+ "keyword": "PartNumber",
+ "value": "03FL194"
+ }
+ },
+ {
+ "compare_vpd": {
+ "fru": "system/chassis/motherboard/pcieslot10/pcie_card10",
+ "keyword": "PartNumber",
+ "value": "03FL204"
+ }
+ }
+ ]
+ }
+ }
+ ]
+ }
+ }
+ ]
+ }
+ }
+ ]
+ }
+ }
+ ]
+ },
+
+ {
+ "comments": [
+ "Rule to determine if a Flett card is present in slot C11.",
+ "This requires a Nisqually pass2+ due to I2C bus number",
+ "differences between pass 1 and pass 2.",
+ "Pass 1 and pass 2 Fletts are both supported.",
+ "Must return true if present and false otherwise."
+ ],
+ "id": "is_flett_c11_present_rule",
+ "actions": [
+ {
+ "if": {
+ "condition": {
+ "comments": ["Check if the Nisqually is pass 2"],
+ "run_rule": "is_pass2_nisqually_rule"
+ },
+ "then": [
+ {
+ "comments": [
+ "Check if a card is present in slot C11"
+ ],
+ "if": {
+ "condition": {
+ "compare_presence": {
+ "fru": "system/chassis/motherboard/pcieslot11/pcie_card11",
+ "value": true
+ }
+ },
+ "then": [
+ {
+ "comments": [
+ "Check if card has Flett CCIN keyword"
+ ],
+ "compare_vpd": {
+ "fru": "system/chassis/motherboard/pcieslot11/pcie_card11",
+ "keyword": "CCIN",
+ "value": "6B87"
+ }
+ }
+ ]
+ }
+ }
+ ]
+ }
+ }
+ ]
+ }
+ ],
+
+ "chassis": [
+ {
+ "comments": ["Chassis (drawer) 1"],
+ "number": 1,
+ "inventory_path": "system/chassis",
+ "devices": [
+ {
+ "comments": [
+ "AVDD / IR38064: Primary PMBus Interface",
+ "In schematic: bus 4 (1-based), address 0xE2 (8-bit)"
+ ],
+ "id": "avdd_regulator",
+ "is_regulator": true,
+ "fru": "system/chassis/motherboard",
+ "i2c_interface": { "bus": 3, "address": "0x71" },
+ "presence_detection": {
+ "rule_id": "is_pass2_nisqually_rule"
+ },
+ "rails": [
+ {
+ "id": "avdd_rail",
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_ir38064_rule"
+ }
+ }
+ ]
+ },
+
+ {
+ "comments": [
+ "3.3VA / TPS549D22",
"In schematic: bus 9 (1-based), address 0x36 (8-bit)",
"Does not have power at standby; cannot be configured",
- "Does not support the PMBus PAGE command" ],
- "id": "3_3va_regulator",
- "is_regulator": true,
- "fru": "system/chassis/motherboard",
- "i2c_interface": { "bus": 8, "address": "0x1B" },
- "rails": [
- {
- "id": "3_3va_rail"
- }
- ]
- },
+ "Does not support the PMBus PAGE command"
+ ],
+ "id": "3_3va_regulator",
+ "is_regulator": true,
+ "fru": "system/chassis/motherboard",
+ "i2c_interface": { "bus": 8, "address": "0x1B" },
+ "rails": [
+ {
+ "id": "3_3va_rail"
+ }
+ ]
+ },
-
- {
- "comments": [ "3.3VB / TPS549D22",
+ {
+ "comments": [
+ "3.3VB / TPS549D22",
"In schematic: bus 4 (1-based), address 0x38 (8-bit)",
"Does not have power at standby; cannot be configured",
- "Does not support the PMBus PAGE command" ],
- "id": "3_3vb_regulator",
- "is_regulator": true,
- "fru": "system/chassis/motherboard",
- "i2c_interface": { "bus": 3, "address": "0x1C" },
- "rails": [
- {
- "id": "3_3vb_rail"
- }
- ]
- },
+ "Does not support the PMBus PAGE command"
+ ],
+ "id": "3_3vb_regulator",
+ "is_regulator": true,
+ "fru": "system/chassis/motherboard",
+ "i2c_interface": { "bus": 3, "address": "0x1C" },
+ "rails": [
+ {
+ "id": "3_3vb_rail"
+ }
+ ]
+ },
+ {
+ "comments": [
+ "VDDp0 DCM 0 / XDPE132G5C: Primary PMBus Interface",
+ "In schematic: bus 10 (1-based), address 0xE2 (8-bit)"
+ ],
+ "id": "vdd_p0_dcm0_regulator",
+ "is_regulator": true,
+ "fru": "system/chassis/motherboard/vdd_vrm0",
+ "i2c_interface": { "bus": 9, "address": "0x71" },
+ "rails": [
+ {
+ "id": "vdd_p0_dcm0_rail",
+ "configuration": {
+ "volts": 0.9,
+ "rule_id": "configure_vdd_rule"
+ },
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_xdpe132g5c_page0_rule"
+ }
+ }
+ ]
+ },
- {
- "comments": [ "VDDp0 DCM 0 / XDPE132G5C: Primary PMBus Interface",
- "In schematic: bus 10 (1-based), address 0xE2 (8-bit)" ],
- "id": "vdd_p0_dcm0_regulator",
- "is_regulator": true,
- "fru": "system/chassis/motherboard/vdd_vrm0",
- "i2c_interface": { "bus": 9, "address": "0x71" },
- "rails": [
- {
- "id": "vdd_p0_dcm0_rail",
- "configuration": {
- "volts": 0.9,
- "rule_id": "configure_vdd_rule"
- },
- "sensor_monitoring": { "rule_id": "read_sensors_xdpe132g5c_page0_rule" }
- }
- ]
- },
+ {
+ "comments": [
+ "VDDp1 DCM 0 / XDPE132G5C: Primary PMBus Interface",
+ "In schematic: bus 10 (1-based), address 0xE0 (8-bit)"
+ ],
+ "id": "vdd_p1_dcm0_regulator",
+ "is_regulator": true,
+ "fru": "system/chassis/motherboard/vdd_vrm0",
+ "i2c_interface": { "bus": 9, "address": "0x70" },
+ "rails": [
+ {
+ "id": "vdd_p1_dcm0_rail",
+ "configuration": {
+ "volts": 0.9,
+ "rule_id": "configure_vdd_rule"
+ },
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_xdpe132g5c_page0_rule"
+ }
+ }
+ ]
+ },
+ {
+ "comments": [
+ "VDDp0 DCM 1 / XDPE132G5C: Primary PMBus Interface",
+ "In schematic: bus 11 (1-based), address 0xE2 (8-bit)"
+ ],
+ "id": "vdd_p0_dcm1_regulator",
+ "is_regulator": true,
+ "fru": "system/chassis/motherboard/vdd_vrm1",
+ "i2c_interface": { "bus": 10, "address": "0x71" },
+ "presence_detection": {
+ "rule_id": "is_dcm1_vrm_present_rule"
+ },
+ "rails": [
+ {
+ "id": "vdd_p0_dcm1_rail",
+ "configuration": {
+ "volts": 0.9,
+ "rule_id": "configure_vdd_rule"
+ },
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_xdpe132g5c_page0_rule"
+ }
+ }
+ ]
+ },
- {
- "comments": [ "VDDp1 DCM 0 / XDPE132G5C: Primary PMBus Interface",
- "In schematic: bus 10 (1-based), address 0xE0 (8-bit)" ],
- "id": "vdd_p1_dcm0_regulator",
- "is_regulator": true,
- "fru": "system/chassis/motherboard/vdd_vrm0",
- "i2c_interface": { "bus": 9, "address": "0x70" },
- "rails": [
- {
- "id": "vdd_p1_dcm0_rail",
- "configuration": {
- "volts": 0.9,
- "rule_id": "configure_vdd_rule"
- },
- "sensor_monitoring": { "rule_id": "read_sensors_xdpe132g5c_page0_rule" }
- }
- ]
- },
+ {
+ "comments": [
+ "VDDp1 DCM 1 / XDPE132G5C: Primary PMBus Interface",
+ "In schematic: bus 11 (1-based), address 0xE0 (8-bit)"
+ ],
+ "id": "vdd_p1_dcm1_regulator",
+ "is_regulator": true,
+ "fru": "system/chassis/motherboard/vdd_vrm1",
+ "i2c_interface": { "bus": 10, "address": "0x70" },
+ "presence_detection": {
+ "rule_id": "is_dcm1_vrm_present_rule"
+ },
+ "rails": [
+ {
+ "id": "vdd_p1_dcm1_rail",
+ "configuration": {
+ "volts": 0.9,
+ "rule_id": "configure_vdd_rule"
+ },
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_xdpe132g5c_page0_rule"
+ }
+ }
+ ]
+ },
+ {
+ "comments": [
+ "VDN & VCSp0 DCM 0 / IR35221: Primary PMBus Interface",
+ "In schematic: bus 10 (1-based), address 0xE4 (8-bit)"
+ ],
+ "id": "vdn_vcs_p0_dcm0_regulator",
+ "is_regulator": true,
+ "fru": "system/chassis/motherboard",
+ "i2c_interface": { "bus": 9, "address": "0x72" },
+ "rails": [
+ {
+ "comments": ["PMBus PAGE 0 rail"],
+ "id": "vdn_dcm0_rail",
+ "configuration": {
+ "volts": 0.9,
+ "rule_id": "configure_vdn_rule"
+ },
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_ir35221_page0_rule"
+ }
+ },
+ {
+ "comments": ["PMBus PAGE 1 rail"],
+ "id": "vcs_p0_dcm0_rail",
+ "configuration": {
+ "volts": 1.0,
+ "rule_id": "configure_vcs_rule"
+ },
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_ir35221_page1_rule"
+ }
+ }
+ ]
+ },
- {
- "comments": [ "VDDp0 DCM 1 / XDPE132G5C: Primary PMBus Interface",
- "In schematic: bus 11 (1-based), address 0xE2 (8-bit)" ],
- "id": "vdd_p0_dcm1_regulator",
- "is_regulator": true,
- "fru": "system/chassis/motherboard/vdd_vrm1",
- "i2c_interface": { "bus": 10, "address": "0x71" },
- "presence_detection": { "rule_id": "is_dcm1_vrm_present_rule" },
- "rails": [
- {
- "id": "vdd_p0_dcm1_rail",
- "configuration": {
- "volts": 0.9,
- "rule_id": "configure_vdd_rule"
- },
- "sensor_monitoring": { "rule_id": "read_sensors_xdpe132g5c_page0_rule" }
- }
- ]
- },
+ {
+ "comments": [
+ "VIO & VCSp1 DCM 0 / IR35221: Primary PMBus Interface",
+ "In schematic: bus 10 (1-based), address 0xE6 (8-bit)"
+ ],
+ "id": "vio_vcs_p1_dcm0_regulator",
+ "is_regulator": true,
+ "fru": "system/chassis/motherboard",
+ "i2c_interface": { "bus": 9, "address": "0x73" },
+ "rails": [
+ {
+ "comments": ["PMBus PAGE 0 rail"],
+ "id": "vio_dcm0_rail",
+ "configuration": {
+ "volts": 1.02,
+ "rule_id": "configure_vio_rule"
+ },
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_ir35221_page0_rule"
+ }
+ },
+ {
+ "comments": ["PMBus PAGE 1 rail"],
+ "id": "vcs_p1_dcm0_rail",
+ "configuration": {
+ "volts": 1.0,
+ "rule_id": "configure_vcs_rule"
+ },
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_ir35221_page1_rule"
+ }
+ }
+ ]
+ },
+ {
+ "comments": [
+ "VDN & VCSp0 DCM 1 / IR35221: Primary PMBus Interface",
+ "In schematic: bus 11 (1-based), address 0xE4 (8-bit)"
+ ],
+ "id": "vdn_vcs_p0_dcm1_regulator",
+ "is_regulator": true,
+ "fru": "system/chassis/motherboard",
+ "i2c_interface": { "bus": 10, "address": "0x72" },
+ "presence_detection": { "rule_id": "is_2s_system_rule" },
+ "rails": [
+ {
+ "comments": ["PMBus PAGE 0 rail"],
+ "id": "vdn_dcm1_rail",
+ "configuration": {
+ "volts": 0.9,
+ "rule_id": "configure_vdn_rule"
+ },
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_ir35221_page0_rule"
+ }
+ },
+ {
+ "comments": ["PMBus PAGE 1 rail"],
+ "id": "vcs_p0_dcm1_rail",
+ "configuration": {
+ "volts": 1.0,
+ "rule_id": "configure_vcs_rule"
+ },
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_ir35221_page1_rule"
+ }
+ }
+ ]
+ },
- {
- "comments": [ "VDDp1 DCM 1 / XDPE132G5C: Primary PMBus Interface",
- "In schematic: bus 11 (1-based), address 0xE0 (8-bit)" ],
- "id": "vdd_p1_dcm1_regulator",
- "is_regulator": true,
- "fru": "system/chassis/motherboard/vdd_vrm1",
- "i2c_interface": { "bus": 10, "address": "0x70" },
- "presence_detection": { "rule_id": "is_dcm1_vrm_present_rule" },
- "rails": [
- {
- "id": "vdd_p1_dcm1_rail",
- "configuration": {
- "volts": 0.9,
- "rule_id": "configure_vdd_rule"
- },
- "sensor_monitoring": { "rule_id": "read_sensors_xdpe132g5c_page0_rule" }
- }
- ]
- },
+ {
+ "comments": [
+ "VIO & VCSp1 DCM 1 / IR35221: Primary PMBus Interface",
+ "In schematic: bus 11 (1-based), address 0xE6 (8-bit)"
+ ],
+ "id": "vio_vcs_p1_dcm1_regulator",
+ "is_regulator": true,
+ "fru": "system/chassis/motherboard",
+ "i2c_interface": { "bus": 10, "address": "0x73" },
+ "presence_detection": { "rule_id": "is_2s_system_rule" },
+ "rails": [
+ {
+ "comments": ["PMBus PAGE 0 rail"],
+ "id": "vio_dcm1_rail",
+ "configuration": {
+ "volts": 1.02,
+ "rule_id": "configure_vio_rule"
+ },
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_ir35221_page0_rule"
+ }
+ },
+ {
+ "comments": ["PMBus PAGE 1 rail"],
+ "id": "vcs_p1_dcm1_rail",
+ "configuration": {
+ "volts": 1.0,
+ "rule_id": "configure_vcs_rule"
+ },
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_ir35221_page1_rule"
+ }
+ }
+ ]
+ },
+ {
+ "comments": [
+ "VPCIe DCM 0 / IR35221: Primary PMBus Interface",
+ "In schematic: bus 10 (1-based), address 0xE8 (8-bit)"
+ ],
+ "id": "vpcie_dcm0_regulator",
+ "is_regulator": true,
+ "fru": "system/chassis/motherboard",
+ "i2c_interface": { "bus": 9, "address": "0x74" },
+ "rails": [
+ {
+ "id": "vpcie_dcm0_rail",
+ "configuration": {
+ "volts": 0.86,
+ "rule_id": "configure_vpcie_rule"
+ },
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_ir35221_page0_rule"
+ }
+ }
+ ]
+ },
- {
- "comments": [ "VDN & VCSp0 DCM 0 / IR35221: Primary PMBus Interface",
- "In schematic: bus 10 (1-based), address 0xE4 (8-bit)" ],
- "id": "vdn_vcs_p0_dcm0_regulator",
- "is_regulator": true,
- "fru": "system/chassis/motherboard",
- "i2c_interface": { "bus": 9, "address": "0x72" },
- "rails": [
- {
- "comments": [ "PMBus PAGE 0 rail" ],
- "id": "vdn_dcm0_rail",
- "configuration": {
- "volts": 0.9,
- "rule_id": "configure_vdn_rule"
- },
- "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" }
- },
- {
- "comments": [ "PMBus PAGE 1 rail" ],
- "id": "vcs_p0_dcm0_rail",
- "configuration": {
- "volts": 1.0,
- "rule_id": "configure_vcs_rule"
- },
- "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page1_rule" }
- }
- ]
- },
+ {
+ "comments": [
+ "VPCIe DCM 1 / IR35221: Primary PMBus Interface",
+ "In schematic: bus 11 (1-based), address 0xE8 (8-bit)"
+ ],
+ "id": "vpcie_dcm1_regulator",
+ "is_regulator": true,
+ "fru": "system/chassis/motherboard",
+ "i2c_interface": { "bus": 10, "address": "0x74" },
+ "presence_detection": { "rule_id": "is_2s_system_rule" },
+ "rails": [
+ {
+ "id": "vpcie_dcm1_rail",
+ "configuration": {
+ "volts": 0.86,
+ "rule_id": "configure_vpcie_rule"
+ },
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_ir35221_page0_rule"
+ }
+ }
+ ]
+ },
-
- {
- "comments": [ "VIO & VCSp1 DCM 0 / IR35221: Primary PMBus Interface",
- "In schematic: bus 10 (1-based), address 0xE6 (8-bit)" ],
- "id": "vio_vcs_p1_dcm0_regulator",
- "is_regulator": true,
- "fru": "system/chassis/motherboard",
- "i2c_interface": { "bus": 9, "address": "0x73" },
- "rails": [
- {
- "comments": [ "PMBus PAGE 0 rail" ],
- "id": "vio_dcm0_rail",
- "configuration": {
- "volts": 1.02,
- "rule_id": "configure_vio_rule"
- },
- "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" }
- },
- {
- "comments": [ "PMBus PAGE 1 rail" ],
- "id": "vcs_p1_dcm0_rail",
- "configuration": {
- "volts": 1.0,
- "rule_id": "configure_vcs_rule"
- },
- "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page1_rule" }
- }
- ]
- },
-
-
- {
- "comments": [ "VDN & VCSp0 DCM 1 / IR35221: Primary PMBus Interface",
- "In schematic: bus 11 (1-based), address 0xE4 (8-bit)" ],
- "id": "vdn_vcs_p0_dcm1_regulator",
- "is_regulator": true,
- "fru": "system/chassis/motherboard",
- "i2c_interface": { "bus": 10, "address": "0x72" },
- "presence_detection": { "rule_id": "is_2s_system_rule" },
- "rails": [
- {
- "comments": [ "PMBus PAGE 0 rail" ],
- "id": "vdn_dcm1_rail",
- "configuration": {
- "volts": 0.9,
- "rule_id": "configure_vdn_rule"
- },
- "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" }
- },
- {
- "comments": [ "PMBus PAGE 1 rail" ],
- "id": "vcs_p0_dcm1_rail",
- "configuration": {
- "volts": 1.0,
- "rule_id": "configure_vcs_rule"
- },
- "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page1_rule" }
- }
- ]
- },
-
-
- {
- "comments": [ "VIO & VCSp1 DCM 1 / IR35221: Primary PMBus Interface",
- "In schematic: bus 11 (1-based), address 0xE6 (8-bit)" ],
- "id": "vio_vcs_p1_dcm1_regulator",
- "is_regulator": true,
- "fru": "system/chassis/motherboard",
- "i2c_interface": { "bus": 10, "address": "0x73" },
- "presence_detection": { "rule_id": "is_2s_system_rule" },
- "rails": [
- {
- "comments": [ "PMBus PAGE 0 rail" ],
- "id": "vio_dcm1_rail",
- "configuration": {
- "volts": 1.02,
- "rule_id": "configure_vio_rule"
- },
- "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" }
- },
- {
- "comments": [ "PMBus PAGE 1 rail" ],
- "id": "vcs_p1_dcm1_rail",
- "configuration": {
- "volts": 1.0,
- "rule_id": "configure_vcs_rule"
- },
- "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page1_rule" }
- }
- ]
- },
-
-
- {
- "comments": [ "VPCIe DCM 0 / IR35221: Primary PMBus Interface",
- "In schematic: bus 10 (1-based), address 0xE8 (8-bit)" ],
- "id": "vpcie_dcm0_regulator",
- "is_regulator": true,
- "fru": "system/chassis/motherboard",
- "i2c_interface": { "bus": 9, "address": "0x74" },
- "rails": [
- {
- "id": "vpcie_dcm0_rail",
- "configuration": {
- "volts": 0.86,
- "rule_id": "configure_vpcie_rule"
- },
- "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" }
- }
- ]
- },
-
-
- {
- "comments": [ "VPCIe DCM 1 / IR35221: Primary PMBus Interface",
- "In schematic: bus 11 (1-based), address 0xE8 (8-bit)" ],
- "id": "vpcie_dcm1_regulator",
- "is_regulator": true,
- "fru": "system/chassis/motherboard",
- "i2c_interface": { "bus": 10, "address": "0x74" },
- "presence_detection": { "rule_id": "is_2s_system_rule" },
- "rails": [
- {
- "id": "vpcie_dcm1_rail",
- "configuration": {
- "volts": 0.86,
- "rule_id": "configure_vpcie_rule"
- },
- "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" }
- }
- ]
- },
-
-
- {
- "comments": [ "Flett Slot C8 / IR35221: Primary PMBus Interface",
+ {
+ "comments": [
+ "Flett Slot C8 / IR35221: Primary PMBus Interface",
"In schematic: bus 7 (1-based) mux channel 3,",
"address 0xEC (8-bit).",
- "BMC I2C bus alias 28" ],
- "id": "flett_slot_c8_regulator",
- "is_regulator": true,
- "fru": "system/chassis/motherboard/pcieslot8/pcie_card8",
- "i2c_interface": { "bus": 28, "address": "0x76" },
- "presence_detection": { "rule_id": "is_flett_c8_present_rule" },
- "rails": [
- {
- "id": "flett_slot_c8_rail",
- "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" }
- }
- ]
- },
+ "BMC I2C bus alias 28"
+ ],
+ "id": "flett_slot_c8_regulator",
+ "is_regulator": true,
+ "fru": "system/chassis/motherboard/pcieslot8/pcie_card8",
+ "i2c_interface": { "bus": 28, "address": "0x76" },
+ "presence_detection": {
+ "rule_id": "is_flett_c8_present_rule"
+ },
+ "rails": [
+ {
+ "id": "flett_slot_c8_rail",
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_ir35221_page0_rule"
+ }
+ }
+ ]
+ },
-
- {
- "comments": [ "Flett Slot C9 / IR35221: Primary PMBus Interface",
+ {
+ "comments": [
+ "Flett Slot C9 / IR35221: Primary PMBus Interface",
"In schematic: bus 7 (1-based) mux channel 2,",
"address 0xEC (8-bit).",
- "BMC I2C bus alias 27" ],
- "id": "flett_slot_c9_regulator",
- "is_regulator": true,
- "fru": "system/chassis/motherboard/pcieslot9/pcie_card9",
- "i2c_interface": { "bus": 27, "address": "0x76" },
- "presence_detection": { "rule_id": "is_flett_c9_present_rule" },
- "rails": [
- {
- "id": "flett_slot_c9_rail",
- "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" }
- }
- ]
- },
+ "BMC I2C bus alias 27"
+ ],
+ "id": "flett_slot_c9_regulator",
+ "is_regulator": true,
+ "fru": "system/chassis/motherboard/pcieslot9/pcie_card9",
+ "i2c_interface": { "bus": 27, "address": "0x76" },
+ "presence_detection": {
+ "rule_id": "is_flett_c9_present_rule"
+ },
+ "rails": [
+ {
+ "id": "flett_slot_c9_rail",
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_ir35221_page0_rule"
+ }
+ }
+ ]
+ },
-
- {
- "comments": [ "Flett Slot C11 / IR35221: Primary PMBus Interface",
+ {
+ "comments": [
+ "Flett Slot C11 / IR35221: Primary PMBus Interface",
"In schematic: bus 12 (1-based) mux channel 1,",
"address 0xEC (8-bit).",
- "BMC I2C bus alias 30" ],
- "id": "flett_slot_c11_regulator",
- "is_regulator": true,
- "fru": "system/chassis/motherboard/pcieslot11/pcie_card11",
- "i2c_interface": { "bus": 30, "address": "0x76" },
- "presence_detection": { "rule_id": "is_flett_c11_present_rule" },
- "rails": [
- {
- "id": "flett_slot_c11_rail",
- "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" }
- }
- ]
- },
+ "BMC I2C bus alias 30"
+ ],
+ "id": "flett_slot_c11_regulator",
+ "is_regulator": true,
+ "fru": "system/chassis/motherboard/pcieslot11/pcie_card11",
+ "i2c_interface": { "bus": 30, "address": "0x76" },
+ "presence_detection": {
+ "rule_id": "is_flett_c11_present_rule"
+ },
+ "rails": [
+ {
+ "id": "flett_slot_c11_rail",
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_ir35221_page0_rule"
+ }
+ }
+ ]
+ },
-
- {
- "comments": [ "Flett Slot C10 / IR35221: Primary PMBus Interface",
+ {
+ "comments": [
+ "Flett Slot C10 / IR35221: Primary PMBus Interface",
"In schematic: bus 12 (1-based) mux channel 0,",
"address 0xEC (8-bit).",
- "BMC I2C bus alias 29" ],
- "id": "flett_slot_c10_regulator",
- "is_regulator": true,
- "fru": "system/chassis/motherboard/pcieslot10/pcie_card10",
- "i2c_interface": { "bus": 29, "address": "0x76" },
- "presence_detection": { "rule_id": "is_flett_c10_present_rule" },
- "rails": [
- {
- "id": "flett_slot_c10_rail",
- "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" }
- }
- ]
+ "BMC I2C bus alias 29"
+ ],
+ "id": "flett_slot_c10_regulator",
+ "is_regulator": true,
+ "fru": "system/chassis/motherboard/pcieslot10/pcie_card10",
+ "i2c_interface": { "bus": 29, "address": "0x76" },
+ "presence_detection": {
+ "rule_id": "is_flett_c10_present_rule"
+ },
+ "rails": [
+ {
+ "id": "flett_slot_c10_rail",
+ "sensor_monitoring": {
+ "rule_id": "read_sensors_ir35221_page0_rule"
+ }
+ }
+ ]
+ }
+ ]
}
- ]
- }
- ]
+ ]
}
-