Remove the GPIOs from Lanyang.py
They are now obtained from a JSON file.
Change-Id: I37ef1b6a4bb39a9f06bb29e15083a8d94b2f1eda
Signed-off-by: Matt Spinler <spinler@us.ibm.com>
diff --git a/configs/Lanyang.py b/configs/Lanyang.py
index a606532..fa7dc96 100644
--- a/configs/Lanyang.py
+++ b/configs/Lanyang.py
@@ -312,57 +312,6 @@
'GPIO_PRESENT' : {}
}
-GPIO_CONFIG = {}
-GPIO_CONFIG['SOFTWARE_PGOOD'] = \
- {'gpio_pin': 'M6', 'direction': 'out'}
-GPIO_CONFIG['BMC_POWER_UP'] = \
- {'gpio_pin': 'E2', 'direction': 'out'} # BMC_PWR_BTN_OUT_N
-GPIO_CONFIG['SYS_PWROK_BUFF'] = \
- {'gpio_pin': 'F6', 'direction': 'in'} # BMC_UCD_PGOOD
-GPIO_CONFIG['PHY_RST_N'] = \
- {'gpio_pin': 'D6', 'direction': 'out'}
-GPIO_CONFIG['HDD_PWR_EN'] = \
- {'gpio_pin': 'B0', 'direction': 'out'} # BMC_HDD1_PWR_EN
-GPIO_CONFIG['CP0_DEVICES_RESET_N'] = \
- {'gpio_pin': 'AA6', 'direction': 'out'} # BMC_CP0_RESET_N
-GPIO_CONFIG['BMC_CP0_PERST_ENABLE'] = \
- {'gpio_pin': 'H3', 'direction': 'out'} # BMC_CP0_PERST_ENABLE_R
-GPIO_CONFIG['BMC_UCD_LATCH_LE'] = \
- {'gpio_pin': 'P4', 'direction': 'out'} # BMC_UCD90160_GPIO
-GPIO_CONFIG['FSI_ENABLE'] = \
- {'gpio_pin': 'D0', 'direction': 'out'} # BMC_FSI_IN_ENA
-GPIO_CONFIG['CRONUS_SEL'] = \
- {'gpio_pin': 'H2', 'direction': 'out'} # BMC_FSI_DBG_PRSNT_N
-GPIO_CONFIG['POWER_BUTTON'] = \
- {'gpio_pin': 'E4', 'direction': 'both'} # PWR_BTN_D_N
-GPIO_CONFIG['RESET_BUTTON'] = \
- {'gpio_pin': 'E3', 'direction': 'both'} # RST_BTN_D_N
-GPIO_CONFIG['PE_MEZZB_PRSNT_N'] = \
- {'gpio_pin': 'P6', 'direction': 'in'}
-GPIO_CONFIG['CHECKSTOP'] = \
- {'gpio_pin': 'F3', 'direction': 'falling'} # BMC_CPU0_JTAG_PRES_N
-
-GPIO_CONFIGS = {
- 'power_config' : {
- 'latch_out': 'BMC_UCD_LATCH_LE',
- 'power_good_in' : 'SYS_PWROK_BUFF',
- 'power_up_outs' : [
- ('SOFTWARE_PGOOD', True),
- ('BMC_POWER_UP', False),
- ],
- 'reset_outs' : [
- ],
- },
- 'hostctl_config' : {
- 'fsi_data' : 'FSI_DATA',
- 'fsi_clk' : 'FSI_CLK',
- 'fsi_enable' : 'FSI_ENABLE',
- 'cronus_sel' : 'CRONUS_SEL',
- 'optionals' : [
- ],
- },
-}
-
# Miscellaneous non-poll sensor with system specific properties.
# The sensor id is the same as those defined in ID_LOOKUP['SENSOR'].
MISC_SENSORS = {