diff --git a/_sources/release-notes/v2.0.9.rst.txt b/_sources/release-notes/v2.0.9.rst.txt
new file mode 100644
index 0000000..ade429b
--- /dev/null
+++ b/_sources/release-notes/v2.0.9.rst.txt
@@ -0,0 +1,65 @@
+Release Notes for OpenPower Firmware v2.0.9
+===========================================
+
+op-build v2.0.9 was released on Thursday August 16th, 2018 and replaces op-build v2.0.8 as the current stable release in
+the 2.0.x series.
+
+It is recommended that v2.0.9 be used over any previous v2.0.x version on POWER9 systems due to the bug fixes contained within.
+
+The only update in this release is to skiboot. Skiboot v6.0.8 includes the following bug fixes:
+
+- i2c: Ensure ordering between i2c_request_send() and completion
+
+  i2c_request_send loops waiting for a flag "uc.done" set by
+  the completion routine, and then look for a result code
+  also set by that same completion.
+
+  There is no synchronization, the completion can happen on another
+  processor, so we need to order the stores to uc and the reads
+  from uc so that uc.done is stored last and tested first using
+  memory barriers.
+- i2c: Fix multiple-enqueue of the same request on NACK
+
+  i2c_request_send() will retry the request if the error is a NAK,
+  however it forgets to clear the "ud.done" flag. It will thus
+  loop again and try to re-enqueue the same request causing internal
+  request list corruption.
+- phb4: Disable 32-bit MSI in capi mode
+
+  If a capi device does a DMA write targeting an address lower than 4GB,
+  it does so through a 32-bit operation, per the PCI spec. In capi mode,
+  the first TVE entry is configured in bypass mode, so the address is
+  valid. But with any (bad) luck, the address could be 0xFFFFxxxx, thus
+  looking like a 32-bit MSI.
+
+  We currently enable both 32-bit and 64-bit MSIs, so the PHB will
+  interpret the DMA write as a MSI, which very likely results in an EEH
+  (MSI with a bad payload size).
+
+  We can fix it by disabling 32-bit MSI when switching the PHB to capi
+  mode. Capi devices are 64-bit.
+
+- capp: Fix the capp recovery timeout comparison
+
+  The current capp recovery timeout control loop in
+  do_capp_recovery_scoms() uses a wrong comparison for return value of
+  tb_compare(). This may cause do_capp_recovery_scoms() to report an
+  timeout earlier than the 168ms stipulated time.
+
+  The patch fixes this by updating the loop timeout control branch in
+  do_capp_recovery_scoms() to use the correct enum tb_cmpval.
+- phb4/capp: Update DMA read engines set in APC_FSM_READ_MASK based on link-width
+
+  Commit 47c09cdfe7a3("phb4/capp: Calculate STQ/DMA read engines based
+  on link-width for PEC") update the CAPP init sequence by calculating
+  the needed STQ/DMA-read engines based on link width and populating it
+  in XPEC_NEST_CAPP_CNTL register. This however needs to be synchronized
+  with the value set in CAPP APC FSM Read Machine Mask Register.
+
+  Hence this patch update phb4_init_capp_regs() to calculate the link
+  width of the stack on PEC2 and populate the same values as previously
+  populated in PEC CAPP_CNTL register.
+
+- core/cpu: Call memset with proper cpu_thread offset
+
+