diff --git a/meta-quanta/meta-gbs/recipes-kernel/linux/linux-nuvoton/0003-Add-basic-support-for-SB-TSI-sensors.patch b/meta-quanta/meta-gbs/recipes-kernel/linux/linux-nuvoton/0003-Add-basic-support-for-SB-TSI-sensors.patch
deleted file mode 100644
index b690a98..0000000
--- a/meta-quanta/meta-gbs/recipes-kernel/linux/linux-nuvoton/0003-Add-basic-support-for-SB-TSI-sensors.patch
+++ /dev/null
@@ -1,327 +0,0 @@
-SB Temperature Sensor Interface (SB-TSI) is an SMBus compatible
-interface that reports AMD SoC's Ttcl (normalized temperature),
-and resembles a typical 8-pin remote temperature sensor's I2C interface
-to BMC.
-
-This commit adds basic support using this interface to read CPU
-temperature, and read/write high/low CPU temp thresholds.
-
-To instantiate this driver on an AMD CPU with SB-TSI
-support, the i2c bus number would be the bus connected from the board
-management controller (BMC) to the CPU. The i2c address is specified in
-Section 6.3.1 of the spec [1]: The SB-TSI address is normally 98h for socket 0
-and 90h for socket 1, but it could vary based on hardware address select pins.
-
-[1]: https://www.amd.com/system/files/TechDocs/56255_OSRR.pdf
-
-Test status: tested reading temp1_input, and reading/writing
-temp1_max/min.
-
-Signed-off-by: Kun Yi <kunyi at google.com>
----
- drivers/hwmon/Kconfig      |  10 ++
- drivers/hwmon/Makefile     |   1 +
- drivers/hwmon/sbtsi_temp.c | 259 +++++++++++++++++++++++++++++++++++++
- 3 files changed, 270 insertions(+)
- create mode 100644 drivers/hwmon/sbtsi_temp.c
-
-diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
-index 05a30832c6ba..9585dcd01d1b 100644
---- a/drivers/hwmon/Kconfig
-+++ b/drivers/hwmon/Kconfig
-@@ -1412,6 +1412,16 @@ config SENSORS_RASPBERRYPI_HWMON
- 	  This driver can also be built as a module. If so, the module
- 	  will be called raspberrypi-hwmon.
- 
-+config SENSORS_SBTSI
-+	tristate "Emulated SB-TSI temperature sensor"
-+	depends on I2C
-+	help
-+	  If you say yes here you get support for emulated temperature
-+	  sensors on AMD SoCs with SB-TSI interface connected to a BMC device.
-+
-+	  This driver can also be built as a module. If so, the module will
-+	  be called sbtsi_temp.
-+
- config SENSORS_SHT15
- 	tristate "Sensiron humidity and temperature sensors. SHT15 and compat."
- 	depends on GPIOLIB || COMPILE_TEST
-diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
-index b0b9c8e57176..cd109f003ce4 100644
---- a/drivers/hwmon/Makefile
-+++ b/drivers/hwmon/Makefile
-@@ -152,6 +152,7 @@ obj-$(CONFIG_SENSORS_POWR1220)  += powr1220.o
- obj-$(CONFIG_SENSORS_PWM_FAN)	+= pwm-fan.o
- obj-$(CONFIG_SENSORS_RASPBERRYPI_HWMON)	+= raspberrypi-hwmon.o
- obj-$(CONFIG_SENSORS_S3C)	+= s3c-hwmon.o
-+obj-$(CONFIG_SENSORS_SBTSI)	+= sbtsi_temp.o
- obj-$(CONFIG_SENSORS_SCH56XX_COMMON)+= sch56xx-common.o
- obj-$(CONFIG_SENSORS_SCH5627)	+= sch5627.o
- obj-$(CONFIG_SENSORS_SCH5636)	+= sch5636.o
-diff --git a/drivers/hwmon/sbtsi_temp.c b/drivers/hwmon/sbtsi_temp.c
-new file mode 100644
-index 000000000000..e3ad6a9f7ec1
---- /dev/null
-+++ b/drivers/hwmon/sbtsi_temp.c
-@@ -0,0 +1,259 @@
-+// SPDX-License-Identifier: GPL-2.0-or-later
-+/*
-+ * sbtsi_temp.c - hwmon driver for a SBI Temperature Sensor Interface (SB-TSI)
-+ *                compliant AMD SoC temperature device.
-+ *
-+ * Copyright (c) 2020, Google Inc.
-+ * Copyright (c) 2020, Kun Yi <kunyi at google.com>
-+ */
-+
-+#include <linux/err.h>
-+#include <linux/i2c.h>
-+#include <linux/init.h>
-+#include <linux/hwmon.h>
-+#include <linux/module.h>
-+#include <linux/mutex.h>
-+#include <linux/of_device.h>
-+#include <linux/of.h>
-+
-+/*
-+ * SB-TSI registers only support SMBus byte data access. "_INT" registers are
-+ * the integer part of a temperature value or limit, and "_DEC" registers are
-+ * corresponding decimal parts.
-+ */
-+#define SBTSI_REG_TEMP_INT		0x01 /* RO */
-+#define SBTSI_REG_STATUS		0x02 /* RO */
-+#define SBTSI_REG_CONFIG		0x03 /* RO */
-+#define SBTSI_REG_TEMP_HIGH_INT		0x07 /* RW */
-+#define SBTSI_REG_TEMP_LOW_INT		0x08 /* RW */
-+#define SBTSI_REG_TEMP_DEC		0x10 /* RW */
-+#define SBTSI_REG_TEMP_HIGH_DEC		0x13 /* RW */
-+#define SBTSI_REG_TEMP_LOW_DEC		0x14 /* RW */
-+#define SBTSI_REG_REV			0xFF /* RO */
-+
-+#define SBTSI_CONFIG_READ_ORDER_SHIFT	5
-+
-+#define SBTSI_TEMP_MIN	0
-+#define SBTSI_TEMP_MAX	255875
-+#define SBTSI_REV_MAX_VALID_ID	4
-+
-+/* Each client has this additional data */
-+struct sbtsi_data {
-+	struct i2c_client *client;
-+	struct mutex lock;
-+};
-+
-+/*
-+ * From SB-TSI spec: CPU temperature readings and limit registers encode the
-+ * temperature in increments of 0.125 from 0 to 255.875. The "high byte"
-+ * register encodes the base-2 of the integer portion, and the upper 3 bits of
-+ * the "low byte" encode in base-2 the decimal portion.
-+ *
-+ * e.g. INT=0x19, DEC=0x20 represents 25.125 degrees Celsius
-+ *
-+ * Therefore temperature in millidegree Celsius =
-+ *   (INT + DEC / 256) * 1000 = (INT * 8 + DEC / 32) * 125
-+ */
-+static inline int sbtsi_reg_to_mc(s32 integer, s32 decimal)
-+{
-+	return ((integer << 3) + (decimal >> 5)) * 125;
-+}
-+
-+/*
-+ * Inversely, given temperature in millidegree Celsius
-+ *   INT = (TEMP / 125) / 8
-+ *   DEC = ((TEMP / 125) % 8) * 32
-+ * Caller have to make sure temp doesn't exceed 255875, the max valid value.
-+ */
-+static inline void sbtsi_mc_to_reg(s32 temp, u8 *integer, u8 *decimal)
-+{
-+	temp /= 125;
-+	*integer = temp >> 3;
-+	*decimal = (temp & 0x7) << 5;
-+}
-+
-+static int sbtsi_read(struct device *dev, enum hwmon_sensor_types type,
-+		      u32 attr, int channel, long *val)
-+{
-+	struct sbtsi_data *data = dev_get_drvdata(dev);
-+	s32 temp_int, temp_dec;
-+	int err, reg_int, reg_dec;
-+	u8 read_order;
-+
-+	if (type != hwmon_temp)
-+		return -EINVAL;
-+
-+	read_order = 0;
-+	switch (attr) {
-+	case hwmon_temp_input:
-+		/*
-+		 * ReadOrder bit specifies the reading order of integer and
-+		 * decimal part of CPU temp for atomic reads. If bit == 0,
-+		 * reading integer part triggers latching of the decimal part,
-+		 * so integer part should be read first. If bit == 1, read
-+		 * order should be reversed.
-+		 */
-+		err = i2c_smbus_read_byte_data(data->client, SBTSI_REG_CONFIG);
-+		if (err < 0)
-+			return err;
-+
-+		read_order = (u8)err & BIT(SBTSI_CONFIG_READ_ORDER_SHIFT);
-+		reg_int = SBTSI_REG_TEMP_INT;
-+		reg_dec = SBTSI_REG_TEMP_DEC;
-+		break;
-+	case hwmon_temp_max:
-+		reg_int = SBTSI_REG_TEMP_HIGH_INT;
-+		reg_dec = SBTSI_REG_TEMP_HIGH_DEC;
-+		break;
-+	case hwmon_temp_min:
-+		reg_int = SBTSI_REG_TEMP_LOW_INT;
-+		reg_dec = SBTSI_REG_TEMP_LOW_DEC;
-+		break;
-+	default:
-+		return -EINVAL;
-+	}
-+
-+	if (read_order == 0) {
-+		temp_int = i2c_smbus_read_byte_data(data->client, reg_int);
-+		temp_dec = i2c_smbus_read_byte_data(data->client, reg_dec);
-+	} else {
-+		temp_dec = i2c_smbus_read_byte_data(data->client, reg_dec);
-+		temp_int = i2c_smbus_read_byte_data(data->client, reg_int);
-+	}
-+
-+	if (temp_int < 0)
-+		return temp_int;
-+	if (temp_dec < 0)
-+		return temp_dec;
-+
-+	*val = sbtsi_reg_to_mc(temp_int, temp_dec);
-+
-+	return 0;
-+}
-+
-+static int sbtsi_write(struct device *dev, enum hwmon_sensor_types type,
-+		       u32 attr, int channel, long val)
-+{
-+	struct sbtsi_data *data = dev_get_drvdata(dev);
-+	int reg_int, reg_dec, err;
-+	u8 temp_int, temp_dec;
-+
-+	if (type != hwmon_temp)
-+		return -EINVAL;
-+
-+	switch (attr) {
-+	case hwmon_temp_max:
-+		reg_int = SBTSI_REG_TEMP_HIGH_INT;
-+		reg_dec = SBTSI_REG_TEMP_HIGH_DEC;
-+		break;
-+	case hwmon_temp_min:
-+		reg_int = SBTSI_REG_TEMP_LOW_INT;
-+		reg_dec = SBTSI_REG_TEMP_LOW_DEC;
-+		break;
-+	default:
-+		return -EINVAL;
-+	}
-+
-+	val = clamp_val(val, SBTSI_TEMP_MIN, SBTSI_TEMP_MAX);
-+	mutex_lock(&data->lock);
-+	sbtsi_mc_to_reg(val, &temp_int, &temp_dec);
-+	err = i2c_smbus_write_byte_data(data->client, reg_int, temp_int);
-+	if (err)
-+		goto exit;
-+
-+	err = i2c_smbus_write_byte_data(data->client, reg_dec, temp_dec);
-+exit:
-+	mutex_unlock(&data->lock);
-+	return err;
-+}
-+
-+static umode_t sbtsi_is_visible(const void *data,
-+				enum hwmon_sensor_types type,
-+				u32 attr, int channel)
-+{
-+	switch (type) {
-+	case hwmon_temp:
-+		switch (attr) {
-+		case hwmon_temp_input:
-+			return 0444;
-+		case hwmon_temp_min:
-+			return 0644;
-+		case hwmon_temp_max:
-+			return 0644;
-+		}
-+		break;
-+	default:
-+		break;
-+	}
-+	return 0;
-+}
-+
-+static const struct hwmon_channel_info *sbtsi_info[] = {
-+	HWMON_CHANNEL_INFO(chip,
-+			   HWMON_C_REGISTER_TZ),
-+	HWMON_CHANNEL_INFO(temp,
-+			   HWMON_T_INPUT | HWMON_T_MIN | HWMON_T_MAX),
-+	NULL
-+};
-+
-+static const struct hwmon_ops sbtsi_hwmon_ops = {
-+	.is_visible = sbtsi_is_visible,
-+	.read = sbtsi_read,
-+	.write = sbtsi_write,
-+};
-+
-+static const struct hwmon_chip_info sbtsi_chip_info = {
-+	.ops = &sbtsi_hwmon_ops,
-+	.info = sbtsi_info,
-+};
-+
-+static int sbtsi_probe(struct i2c_client *client,
-+		       const struct i2c_device_id *id)
-+{
-+	struct device *dev = &client->dev;
-+	struct device *hwmon_dev;
-+	struct sbtsi_data *data;
-+
-+	data = devm_kzalloc(dev, sizeof(struct sbtsi_data), GFP_KERNEL);
-+	if (!data)
-+		return -ENOMEM;
-+
-+	data->client = client;
-+	mutex_init(&data->lock);
-+
-+	hwmon_dev =
-+		devm_hwmon_device_register_with_info(dev, client->name, data,
-+						     &sbtsi_chip_info, NULL);
-+
-+	return PTR_ERR_OR_ZERO(hwmon_dev);
-+}
-+
-+static const struct i2c_device_id sbtsi_id[] = {
-+	{"sbtsi", 0},
-+	{}
-+};
-+MODULE_DEVICE_TABLE(i2c, sbtsi_id);
-+
-+static const struct of_device_id __maybe_unused sbtsi_of_match[] = {
-+	{
-+		.compatible = "amd,sbtsi",
-+	},
-+	{ },
-+};
-+MODULE_DEVICE_TABLE(of, sbtsi_of_match);
-+
-+static struct i2c_driver sbtsi_driver = {
-+	.class = I2C_CLASS_HWMON,
-+	.driver = {
-+		.name = "sbtsi",
-+		.of_match_table = of_match_ptr(sbtsi_of_match),
-+	},
-+	.probe = sbtsi_probe,
-+	.id_table = sbtsi_id,
-+};
-+
-+module_i2c_driver(sbtsi_driver);
-+
-+MODULE_AUTHOR("Kun Yi <kunyi at google.com>");
-+MODULE_DESCRIPTION("Hwmon driver for AMD SB-TSI emulated sensor");
-+MODULE_LICENSE("GPL");
--- 
-2.26.0.292.g33ef6b2f38-goog
\ No newline at end of file
diff --git a/meta-quanta/meta-gbs/recipes-kernel/linux/linux-nuvoton_%.bbappend b/meta-quanta/meta-gbs/recipes-kernel/linux/linux-nuvoton_%.bbappend
index 4de4ca9..e5fadfe 100644
--- a/meta-quanta/meta-gbs/recipes-kernel/linux/linux-nuvoton_%.bbappend
+++ b/meta-quanta/meta-gbs/recipes-kernel/linux/linux-nuvoton_%.bbappend
@@ -1,6 +1,5 @@
 FILESEXTRAPATHS_prepend_gbs := "${THISDIR}/linux-nuvoton:"
 SRC_URI_append_gbs = " file://gbs.cfg"
-SRC_URI_append_gbs = " file://0003-Add-basic-support-for-SB-TSI-sensors.patch"
 SRC_URI_append_gbs = " file://0004-Add-kernel-seven-seg-display-support.patch"
 SRC_URI_append_gbs = " file://0004-ben-drivers-misc-Character-device-driver-for-seven-segme.patch"
 SRC_URI_append_gbs = " file://0004-ben-drivers-misc-Platform-driver-for-seven-segment-displ.patch"