meta-raspberrypi: subtree update:e2c1992955..cc6074c660
Andrei Gherzan (1):
sdcard_image-rpi.bbclass: Fix when RPI_SDIMG_EXTRA_DEPENDS not defined
Christopher Clark (2):
sdcard_image-rpi.bbclass: enable extensible inclusion into boot
docs/extra-build-config.md: document vars to add to boot partition
Fabio Berton (1):
u-boot: Move fw_env.config to u-boot append
Jakub Luzny (2):
rpi-config: Add CAN_OSCILLATOR variable to set mcp2515 crystal frequency
docs/extra-build-config.md: Document CAN_OSCILLATOR variable
Jeff Ithier (1):
Generalize the naming of the bootfiles deploy directory
Martin Jansa (1):
linux-raspberrypi-5.4: bump SRCREV to latest to fix perf build
Pierre-Jean Texier (3):
rpi-default-versions: Switch defaults to 5.4
raspberrypi-firmware: update to current HEAD
linux-raspberrypi: bump to revision 4b945d5
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
Change-Id: I50eca26a801bfe014d3cea271f0cb91e7b653445
diff --git a/meta-raspberrypi/recipes-bsp/bootfiles/bcm2835-bootfiles.bb b/meta-raspberrypi/recipes-bsp/bootfiles/bootfiles.bb
similarity index 90%
rename from meta-raspberrypi/recipes-bsp/bootfiles/bcm2835-bootfiles.bb
rename to meta-raspberrypi/recipes-bsp/bootfiles/bootfiles.bb
index d20312c..80e226d 100644
--- a/meta-raspberrypi/recipes-bsp/bootfiles/bcm2835-bootfiles.bb
+++ b/meta-raspberrypi/recipes-bsp/bootfiles/bootfiles.bb
@@ -1,4 +1,4 @@
-DESCRIPTION = "Closed source binary files to help boot the ARM on the BCM2835."
+DESCRIPTION = "Closed source binary files to help boot all raspberry pi devices."
LICENSE = "Broadcom-RPi"
LIC_FILES_CHKSUM = "file://LICENCE.broadcom;md5=c403841ff2837657b2ed8e5bb474ac8d"
diff --git a/meta-raspberrypi/recipes-bsp/bootfiles/rpi-config_git.bb b/meta-raspberrypi/recipes-bsp/bootfiles/rpi-config_git.bb
index afdbce6..9489951 100644
--- a/meta-raspberrypi/recipes-bsp/bootfiles/rpi-config_git.bb
+++ b/meta-raspberrypi/recipes-bsp/bootfiles/rpi-config_git.bb
@@ -28,211 +28,213 @@
GPIO_IR ?= "18"
GPIO_IR_TX ?= "17"
+CAN_OSCILLATOR ?= "16000000"
+
inherit deploy nopackages
do_deploy() {
- install -d ${DEPLOYDIR}/bcm2835-bootfiles
+ install -d ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}
- cp ${S}/config.txt ${DEPLOYDIR}/bcm2835-bootfiles/
+ cp ${S}/config.txt ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/
if [ -n "${KEY_DECODE_MPG2}" ]; then
- sed -i '/#decode_MPG2=/ c\decode_MPG2=${KEY_DECODE_MPG2}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#decode_MPG2=/ c\decode_MPG2=${KEY_DECODE_MPG2}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ -n "${KEY_DECODE_WVC1}" ]; then
- sed -i '/#decode_WVC1=/ c\decode_WVC1=${KEY_DECODE_WVC1}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#decode_WVC1=/ c\decode_WVC1=${KEY_DECODE_WVC1}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ -n "${DISABLE_OVERSCAN}" ]; then
- sed -i '/#disable_overscan=/ c\disable_overscan=${DISABLE_OVERSCAN}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#disable_overscan=/ c\disable_overscan=${DISABLE_OVERSCAN}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ "${DISABLE_SPLASH}" = "1" ]; then
- sed -i '/#disable_splash=/ c\disable_splash=${DISABLE_SPLASH}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#disable_splash=/ c\disable_splash=${DISABLE_SPLASH}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
# Set overclocking options
if [ -n "${ARM_FREQ}" ]; then
- sed -i '/#arm_freq=/ c\arm_freq=${ARM_FREQ}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#arm_freq=/ c\arm_freq=${ARM_FREQ}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ -n "${GPU_FREQ}" ]; then
- sed -i '/#gpu_freq=/ c\gpu_freq=${GPU_FREQ}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#gpu_freq=/ c\gpu_freq=${GPU_FREQ}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ -n "${CORE_FREQ}" ]; then
- sed -i '/#core_freq=/ c\core_freq=${CORE_FREQ}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#core_freq=/ c\core_freq=${CORE_FREQ}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ -n "${SDRAM_FREQ}" ]; then
- sed -i '/#sdram_freq=/ c\sdram_freq=${SDRAM_FREQ}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#sdram_freq=/ c\sdram_freq=${SDRAM_FREQ}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ -n "${OVER_VOLTAGE}" ]; then
- sed -i '/#over_voltage=/ c\over_voltage=${OVER_VOLTAGE}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#over_voltage=/ c\over_voltage=${OVER_VOLTAGE}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
# GPU memory
if [ -n "${GPU_MEM}" ]; then
- sed -i '/#gpu_mem=/ c\gpu_mem=${GPU_MEM}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#gpu_mem=/ c\gpu_mem=${GPU_MEM}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ -n "${GPU_MEM_256}" ]; then
- sed -i '/#gpu_mem_256=/ c\gpu_mem_256=${GPU_MEM_256}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#gpu_mem_256=/ c\gpu_mem_256=${GPU_MEM_256}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ -n "${GPU_MEM_512}" ]; then
- sed -i '/#gpu_mem_512=/ c\gpu_mem_512=${GPU_MEM_512}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#gpu_mem_512=/ c\gpu_mem_512=${GPU_MEM_512}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ -n "${GPU_MEM_1024}" ]; then
- sed -i '/#gpu_mem_1024=/ c\gpu_mem_1024=${GPU_MEM_1024}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#gpu_mem_1024=/ c\gpu_mem_1024=${GPU_MEM_1024}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
# Set boot delay
if [ -n "${BOOT_DELAY}" ]; then
- sed -i '/#boot_delay=/ c\boot_delay=${BOOT_DELAY}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#boot_delay=/ c\boot_delay=${BOOT_DELAY}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ -n "${BOOT_DELAY_MS}" ]; then
- sed -i '/#boot_delay_ms=/ c\boot_delay_ms=${BOOT_DELAY_MS}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#boot_delay_ms=/ c\boot_delay_ms=${BOOT_DELAY_MS}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
# Set HDMI and composite video options
if [ -n "${HDMI_FORCE_HOTPLUG}" ]; then
- sed -i '/#hdmi_force_hotplug=/ c\hdmi_force_hotplug=${HDMI_FORCE_HOTPLUG}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#hdmi_force_hotplug=/ c\hdmi_force_hotplug=${HDMI_FORCE_HOTPLUG}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ -n "${HDMI_DRIVE}" ]; then
- sed -i '/#hdmi_drive=/ c\hdmi_drive=${HDMI_DRIVE}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#hdmi_drive=/ c\hdmi_drive=${HDMI_DRIVE}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ -n "${HDMI_GROUP}" ]; then
- sed -i '/#hdmi_group=/ c\hdmi_group=${HDMI_GROUP}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#hdmi_group=/ c\hdmi_group=${HDMI_GROUP}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ -n "${HDMI_MODE}" ]; then
- sed -i '/#hdmi_mode=/ c\hdmi_mode=${HDMI_MODE}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#hdmi_mode=/ c\hdmi_mode=${HDMI_MODE}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ -n "${CONFIG_HDMI_BOOST}" ]; then
- sed -i '/#config_hdmi_boost=/ c\config_hdmi_boost=${CONFIG_HDMI_BOOST}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#config_hdmi_boost=/ c\config_hdmi_boost=${CONFIG_HDMI_BOOST}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ -n "${SDTV_MODE}" ]; then
- sed -i '/#sdtv_mode=/ c\sdtv_mode=${SDTV_MODE}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#sdtv_mode=/ c\sdtv_mode=${SDTV_MODE}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ -n "${SDTV_ASPECT}" ]; then
- sed -i '/#sdtv_aspect=/ c\sdtv_aspect=${SDTV_ASPECT}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#sdtv_aspect=/ c\sdtv_aspect=${SDTV_ASPECT}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ -n "${DISPLAY_ROTATE}" ]; then
- sed -i '/#display_rotate=/ c\display_rotate=${DISPLAY_ROTATE}' ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ sed -i '/#display_rotate=/ c\display_rotate=${DISPLAY_ROTATE}' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
# Video camera support
if [ "${VIDEO_CAMERA}" = "1" ]; then
- echo "# Enable video camera" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "start_x=1" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "# Enable video camera" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "start_x=1" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
# Offline compositing support
if [ "${DISPMANX_OFFLINE}" = "1" ]; then
- echo "# Enable offline compositing" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "dispmanx_offline=1" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "# Enable offline compositing" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "dispmanx_offline=1" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
# SPI bus support
if [ "${ENABLE_SPI_BUS}" = "1" ] || [ "${PITFT}" = "1" ]; then
- echo "# Enable SPI bus" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "dtparam=spi=on" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "# Enable SPI bus" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "dtparam=spi=on" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
# I2C support
if [ "${ENABLE_I2C}" = "1" ] || [ "${PITFT}" = "1" ]; then
- echo "# Enable I2C" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "dtparam=i2c1=on" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "dtparam=i2c_arm=on" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "# Enable I2C" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "dtparam=i2c1=on" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "dtparam=i2c_arm=on" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
# PiTFT22 display support
if [ "${PITFT22}" = "1" ]; then
- echo "# Enable PITFT22 display" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "dtoverlay=pitft22,rotate=270,speed=32000000,txbuflen=32768" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "# Enable PITFT22 display" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "dtoverlay=pitft22,rotate=270,speed=32000000,txbuflen=32768" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ "${PITFT28r}" = "1" ]; then
- echo "# Enable PITFT28r display" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "dtoverlay=pitft28-resistive,rotate=90,speed=32000000,txbuflen=32768" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "# Enable PITFT28r display" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "dtoverlay=pitft28-resistive,rotate=90,speed=32000000,txbuflen=32768" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ "${PITFT28c}" = "1" ]; then
- echo "# Enable PITFT28c display" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "dtoverlay=pitft28-capacitive,rotate=90,speed=32000000,txbuflen=32768" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "dtoverlay=pitft28-capacitive,touch-swapxy,touch-invx" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "# Enable PITFT28c display" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "dtoverlay=pitft28-capacitive,rotate=90,speed=32000000,txbuflen=32768" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "dtoverlay=pitft28-capacitive,touch-swapxy,touch-invx" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
if [ "${PITFT35r}" = "1" ]; then
- echo "# Enable PITFT35r display" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "dtoverlay=pitft35-resistive,rotate=90,speed=42000000,fps=20" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "# Enable PITFT35r display" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "dtoverlay=pitft35-resistive,rotate=90,speed=42000000,fps=20" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
# UART support
if [ "${ENABLE_UART}" = "1" ]; then
- echo "# Enable UART" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "enable_uart=1" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "# Enable UART" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "enable_uart=1" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
# Infrared support
if [ "${ENABLE_IR}" = "1" ]; then
- echo "# Enable infrared" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "dtoverlay=gpio-ir,gpio_pin=${GPIO_IR}" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "dtoverlay=gpio-ir-tx,gpio_pin=${GPIO_IR_TX}" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "# Enable infrared" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "dtoverlay=gpio-ir,gpio_pin=${GPIO_IR}" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "dtoverlay=gpio-ir-tx,gpio_pin=${GPIO_IR_TX}" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
# VC4 Graphics support
if [ "${VC4GRAPHICS}" = "1" ]; then
- echo "# Enable VC4 Graphics" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "dtoverlay=${VC4DTBO}" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "# Enable VC4 Graphics" >> ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "dtoverlay=${VC4DTBO}" >> ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
# Waveshare "C" 1024x600 7" Rev2.1 IPS capacitive touch (http://www.waveshare.com/7inch-HDMI-LCD-C.htm)
if [ "${WAVESHARE_1024X600_C_2_1}" = "1" ]; then
- echo "# Waveshare \"C\" 1024x600 7\" Rev2.1 IPS capacitive touch screen" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "max_usb_current=1" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "hdmi_group=2" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "hdmi_mode=87" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "hdmi_cvt 1024 600 60 6 0 0 0" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "hdmi_drive=1" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "# Waveshare \"C\" 1024x600 7\" Rev2.1 IPS capacitive touch screen" >> ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "max_usb_current=1" >> ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "hdmi_group=2" >> ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "hdmi_mode=87" >> ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "hdmi_cvt 1024 600 60 6 0 0 0" >> ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "hdmi_drive=1" >> ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
# DWC2 USB peripheral support
if [ "${ENABLE_DWC2_PERIPHERAL}" = "1" ]; then
- echo "# Enable USB peripheral mode" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "dtoverlay=dwc2,dr_mode=peripheral" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "# Enable USB peripheral mode" >> ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "dtoverlay=dwc2,dr_mode=peripheral" >> ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
# AT86RF23X support
if [ "${ENABLE_AT86RF}" = "1" ]; then
- echo "# Enable AT86RF23X" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "dtoverlay=at86rf233,speed=3000000" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "# Enable AT86RF23X" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "dtoverlay=at86rf233,speed=3000000" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
# ENABLE DUAL CAN
if [ "${ENABLE_DUAL_CAN}" = "1" ]; then
- echo "# Enable DUAL CAN" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "dtoverlay=mcp2515-can0,oscillator=16000000,interrupt=25" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "dtoverlay=mcp2515-can1,oscillator=16000000,interrupt=24" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "# Enable DUAL CAN" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "dtoverlay=mcp2515-can0,oscillator=${CAN_OSCILLATOR},interrupt=25" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "dtoverlay=mcp2515-can1,oscillator=${CAN_OSCILLATOR},interrupt=24" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
# ENABLE CAN
elif [ "${ENABLE_CAN}" = "1" ]; then
- echo "# Enable CAN" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "dtoverlay=mcp2515-can0,oscillator=16000000,interrupt=25" >>${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "# Enable CAN" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "dtoverlay=mcp2515-can0,oscillator=${CAN_OSCILLATOR},interrupt=25" >>${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
fi
# Append extra config if the user has provided any
- printf "${RPI_EXTRA_CONFIG}\n" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ printf "${RPI_EXTRA_CONFIG}\n" >> ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
# Handle setup with armstub file
if [ "${@bb.utils.contains("MACHINE_FEATURES", "armstub", "1", "0", d)}" = "1" ]; then
- echo "\n# ARM stub configuration" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "armstub=${ARMSTUB}" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "\n# ARM stub configuration" >> ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "armstub=${ARMSTUB}" >> ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
case "${ARMSTUB}" in
*-gic.bin)
- echo "enable_gic=1" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "enable_gic=1" >> ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
;;
esac
fi
}
do_deploy_append_raspberrypi3-64() {
- echo "# have a properly sized image" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "disable_overscan=1" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "# have a properly sized image" >> ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "disable_overscan=1" >> ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
- echo "# Enable audio (loads snd_bcm2835)" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
- echo "dtparam=audio=on" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "# Enable audio (loads snd_bcm2835)" >> ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
+ echo "dtparam=audio=on" >> ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt
}
addtask deploy before do_build after do_install
-do_deploy[dirs] += "${DEPLOYDIR}/bcm2835-bootfiles"
+do_deploy[dirs] += "${DEPLOYDIR}/${BOOTFILES_DIR_NAME}"
PACKAGE_ARCH = "${MACHINE_ARCH}"