| # |
| # Sample configuration file for TAYGA 0.9.2 |
| # |
| # Modify this to use your own addresses!! |
| # |
| |
| # |
| # TUN device that TAYGA will use to exchange IPv4 and IPv6 packets with the |
| # kernel. You may use any name you like, but `nat64' is recommended. |
| # |
| # This device may be created before starting the tayga daemon by running |
| # `tayga --mktun`. This allows routing and firewall rules to be set up prior |
| # to commencement of packet translation. |
| # |
| # Mandatory. |
| # |
| tun-device nat64 |
| |
| # |
| # TAYGA's IPv4 address. This is NOT your router's IPv4 address! TAYGA |
| # requires its own address because it acts as an IPv4 and IPv6 router, and |
| # needs to be able to send ICMP messages. TAYGA will also respond to ICMP |
| # echo requests (ping) at this address. |
| # |
| # This address can safely be located inside the dynamic-pool prefix. |
| # |
| # Mandatory. |
| # |
| ipv4-addr 192.168.254.1 |
| |
| # |
| # TAYGA's IPv6 address. This is NOT your router's IPv6 address! TAYGA |
| # requires its own address because it acts as an IPv4 and IPv6 router, and |
| # needs to be able to send ICMP messages. TAYGA will also respond to ICMP |
| # echo requests (ping6) at this address. |
| # |
| # You can leave ipv6-addr unspecified and TAYGA will construct its IPv6 |
| # address using ipv4-addr and the NAT64 prefix. |
| # |
| # Optional if the NAT64 prefix is specified, otherwise mandatory. It is also |
| # mandatory if the NAT64 prefix is 64:ff9b::/96 and ipv4-addr is a private |
| # (RFC1918) address. |
| # |
| #ipv6-addr 2001:db8:1::2 |
| ipv6-addr fdaa:bb:1::1 |
| |
| # |
| # The NAT64 prefix. The IPv4 address space is mapped into the IPv6 address |
| # space by prepending this prefix to the IPv4 address. Using a /96 prefix is |
| # recommended in most situations, but all lengths specified in RFC 6052 are |
| # supported. |
| # |
| # This must be a prefix selected from your organization's IPv6 address space |
| # or the Well-Known Prefix 64:ff9b::/96. Note that using the Well-Known |
| # Prefix will prohibit IPv6 hosts from contacting IPv4 hosts that have private |
| # (RFC1918) addresses, per RFC 6052. |
| # |
| # The NAT64 prefix need not be specified if all required address mappings are |
| # listed in `map' directives. (See below.) |
| # |
| # Optional. |
| # |
| ##prefix 2001:db8:1:ffff::/96 |
| prefix 64:ff9b::/96 |
| |
| # |
| # Dynamic pool prefix. IPv6 hosts which send traffic through TAYGA (and do |
| # not correspond to a static map or an IPv4-translatable address in the NAT64 |
| # prefix) will be assigned an IPv4 address from the dynamic pool. Dynamic |
| # maps are valid for 124 minutes after the last matching packet is seen. |
| # |
| # If no unassigned addresses remain in the dynamic pool (or no dynamic pool is |
| # configured), packets from unknown IPv6 hosts will be rejected with an ICMP |
| # unreachable error. |
| # |
| # Optional. |
| # |
| dynamic-pool 192.168.254.0/24 |
| |
| # |
| # Persistent data storage directory. The dynamic.map file, which saves the |
| # dynamic maps that are created from dynamic-pool, is stored in this |
| # directory. Omit if you do not need these maps to be persistent between |
| # instances of TAYGA. |
| # |
| # Optional. |
| # |
| data-dir /var/spool/tayga |
| |
| # |
| # Establishes a single-host map. If an IPv6 host should be consistently |
| # reachable at a specific IPv4 address, the mapping can be specified in a |
| # `map' directive. (IPv6 hosts numbered with an IPv4-translatable address do |
| # not need map directives.) |
| # |
| # IPv4 addresses specified in the `map' directive can safely be located inside |
| # the dynamic-pool prefix. |
| # |
| # Optional. |
| # |
| #map 192.168.5.42 2001:db8:1:4444::1 |
| #map 192.168.5.43 2001:db8:1:4444::2 |
| #map 192.168.255.2 2001:db8:1:569::143 |