blob: 987ee0fa082a9223784bc813f18546b23f3cd11d [file] [log] [blame]
*** Settings ***
Documentation Network interface configuration and verification
... tests.
Resource ../../lib/bmc_redfish_resource.robot
Resource ../../lib/bmc_network_utils.robot
Resource ../../lib/openbmc_ffdc.robot
Library ../../lib/bmc_network_utils.py
Library Collections
Test Setup Test Setup Execution
Test Teardown Test Teardown Execution
Suite Setup Suite Setup Execution
Force Tags Network_Conf_Test
*** Variables ***
${test_hostname} openbmc
${test_ipv4_addr} 10.7.7.7
${test_ipv4_invalid_addr} 0.0.1.a
${test_subnet_mask} 255.255.0.0
${broadcast_ip} 10.7.7.255
${loopback_ip} 127.0.0.2
${multicast_ip} 224.6.6.6
${out_of_range_ip} 10.7.7.256
${test_ipv4_addr2} 10.7.7.8
# Valid netmask is 4 bytes long and has continuous block of 1s.
# Maximum valid value in each octet is 255 and least value is 0.
# 253 is not valid, as binary value is 11111101.
${invalid_netmask} 255.255.253.0
${alpha_netmask} ff.ff.ff.ff
# Maximum value of octet in netmask is 255.
${out_of_range_netmask} 255.256.255.0
${more_byte_netmask} 255.255.255.0.0
${less_byte_netmask} 255.255.255
${threshold_netmask} 255.255.255.255
${lowest_netmask} 128.0.0.0
# There will be 4 octets in IP address (e.g. xx.xx.xx.xx)
# but trying to configure xx.xx.xx
${less_octet_ip} 10.3.36
# For the address 10.6.6.6, the 10.6.6.0 portion describes the
# network ID and the 6 describe the host.
${network_id} 10.7.7.0
${hex_ip} 0xa.0xb.0xc.0xd
${negative_ip} 10.-7.-7.7
@{static_name_servers} 10.5.5.5
@{null_value} null
@{empty_dictionary} {}
@{string_value} aa.bb.cc.dd
*** Test Cases ***
Get IP Address And Verify
[Documentation] Get IP Address And Verify.
[Tags] Get_IP_Address_And_Verify
FOR ${network_configuration} IN @{network_configurations}
Verify IP On BMC ${network_configuration['Address']}
END
Get Netmask And Verify
[Documentation] Get Netmask And Verify.
[Tags] Get_Netmask_And_Verify
FOR ${network_configuration} IN @{network_configurations}
Verify Netmask On BMC ${network_configuration['SubnetMask']}
END
Get Gateway And Verify
[Documentation] Get gateway and verify it's existence on the BMC.
[Tags] Get_Gateway_And_Verify
FOR ${network_configuration} IN @{network_configurations}
Verify Gateway On BMC ${network_configuration['Gateway']}
END
Get MAC Address And Verify
[Documentation] Get MAC address and verify it's existence on the BMC.
[Tags] Get_MAC_Address_And_Verify
${active_channel_config}= Get Active Channel Config
${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']}
${resp}= Redfish.Get ${REDFISH_NW_ETH_IFACE}${ethernet_interface}
${macaddr}= Get From Dictionary ${resp.dict} MACAddress
Validate MAC On BMC ${macaddr}
Verify All Configured IP And Netmask
[Documentation] Verify all configured IP and netmask on BMC.
[Tags] Verify_All_Configured_IP_And_Netmask
FOR ${network_configuration} IN @{network_configurations}
Verify IP And Netmask On BMC ${network_configuration['Address']}
... ${network_configuration['SubnetMask']}
END
Get Hostname And Verify
[Documentation] Get hostname via Redfish and verify.
[Tags] Get_Hostname_And_Verify
${hostname}= Redfish_Utils.Get Attribute ${REDFISH_NW_PROTOCOL_URI} HostName
Validate Hostname On BMC ${hostname}
Configure Hostname And Verify
[Documentation] Configure hostname via Redfish and verify.
[Tags] Configure_Hostname_And_Verify
[Teardown] Run Keywords
... Configure Hostname ${hostname} AND Validate Hostname On BMC ${hostname}
${hostname}= Redfish_Utils.Get Attribute ${REDFISH_NW_PROTOCOL_URI} HostName
Configure Hostname ${test_hostname}
Validate Hostname On BMC ${test_hostname}
Add Valid IPv4 Address And Verify
[Documentation] Add IPv4 Address via Redfish and verify.
[Tags] Add_Valid_IPv4_Addres_And_Verify
[Teardown] Run Keywords
... Delete IP Address ${test_ipv4_addr} AND Test Teardown Execution
Add IP Address ${test_ipv4_addr} ${test_subnet_mask} ${test_gateway}
Add Invalid IPv4 Address And Verify
[Documentation] Add Invalid IPv4 Address via Redfish and verify.
[Tags] Add_Invalid_IPv4_Addres_And_Verify
Add IP Address ${test_ipv4_invalid_addr} ${test_subnet_mask}
... ${test_gateway} valid_status_codes=${HTTP_BAD_REQUEST}
Configure Out Of Range IP
[Documentation] Configure out-of-range IP address.
[Tags] Configure_Out_Of_Range_IP
[Template] Add IP Address
# ip subnet_mask gateway valid_status_codes
${out_of_range_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST}
Configure Broadcast IP
[Documentation] Configure broadcast IP address.
[Tags] Configure_Broadcast_IP
[Template] Add IP Address
[Teardown] Clear IP Settings On Fail ${broadcast_ip}
# ip subnet_mask gateway valid_status_codes
${broadcast_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST}
Configure Multicast IP
[Documentation] Configure multicast IP address.
[Tags] Configure_Multicast_IP
[Template] Add IP Address
[Teardown] Clear IP Settings On Fail ${multicast_ip}
# ip subnet_mask gateway valid_status_codes
${multicast_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST}
Configure Loopback IP
[Documentation] Configure loopback IP address.
[Tags] Configure_Loopback_IP
[Template] Add IP Address
[Teardown] Clear IP Settings On Fail ${loopback_ip}
# ip subnet_mask gateway valid_status_codes
${loopback_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST}
Add Valid IPv4 Address And Check Persistency
[Documentation] Add IPv4 address and check peristency.
[Tags] Add_Valid_IPv4_Addres_And_Check_Persistency
Add IP Address ${test_ipv4_addr} ${test_subnet_mask} ${test_gateway}
# Reboot BMC and verify persistency.
OBMC Reboot (off)
Redfish.Login
Verify IP On BMC ${test_ipv4_addr}
Delete IP Address ${test_ipv4_addr}
Add Fourth Octet Threshold IP And Verify
[Documentation] Add fourth octet threshold IP and verify.
[Tags] Add_Fourth_Octet_Threshold_IP_And_Verify
[Teardown] Run Keywords
... Delete IP Address 10.7.7.254 AND Test Teardown Execution
Add IP Address 10.7.7.254 ${test_subnet_mask} ${test_gateway}
Add Fourth Octet Lowest IP And Verify
[Documentation] Add fourth octet lowest IP and verify.
[Tags] Add_Fourth_Octet_Lowest_IP_And_Verify
[Teardown] Run Keywords
... Delete IP Address 10.7.7.1 AND Test Teardown Execution
Add IP Address 10.7.7.1 ${test_subnet_mask} ${test_gateway}
Add Third Octet Threshold IP And Verify
[Documentation] Add third octet threshold IP and verify.
[Tags] Add_Third_Octet_Threshold_IP_And_Verify
[Teardown] Run Keywords
... Delete IP Address 10.7.255.7 AND Test Teardown Execution
Add IP Address 10.7.255.7 ${test_subnet_mask} ${test_gateway}
Add Third Octet Lowest IP And Verify
[Documentation] Add third octet lowest IP and verify.
[Tags] Add_Third_Octet_Lowest_IP_And_Verify
[Teardown] Run Keywords
... Delete IP Address 10.7.0.7 AND Test Teardown Execution
Add IP Address 10.7.0.7 ${test_subnet_mask} ${test_gateway}
Add Second Octet Threshold IP And Verify
[Documentation] Add second octet threshold IP and verify.
[Tags] Add_Second_Octet_Threshold_IP_And_Verify
[Teardown] Run Keywords
... Delete IP Address 10.255.7.7 AND Test Teardown Execution
Add IP Address 10.255.7.7 ${test_subnet_mask} ${test_gateway}
Add Second Octet Lowest IP And Verify
[Documentation] Add second octet lowest IP and verify.
[Tags] Add_Second_Octet_Lowest_IP_And_Verify
[Teardown] Run Keywords
... Delete IP Address 10.0.7.7 AND Test Teardown Execution
Add IP Address 10.0.7.7 ${test_subnet_mask} ${test_gateway}
Add First Octet Threshold IP And Verify
[Documentation] Add first octet threshold IP and verify.
[Tags] Add_First_Octet_Threshold_IP_And_Verify
[Teardown] Run Keywords
... Delete IP Address 223.7.7.7 AND Test Teardown Execution
Add IP Address 223.7.7.7 ${test_subnet_mask} ${test_gateway}
Add First Octet Lowest IP And Verify
[Documentation] Add first octet lowest IP and verify.
[Tags] Add_First_Octet_Lowest_IP_And_Verify
[Teardown] Run Keywords
... Delete IP Address 1.7.7.7 AND Test Teardown Execution
Add IP Address 1.7.7.7 ${test_subnet_mask} ${test_gateway}
Configure Invalid Netmask
[Documentation] Verify error while setting invalid netmask.
[Tags] Configure_Invalid_Netmask
[Template] Add IP Address
# ip subnet_mask gateway valid_status_codes
${test_ipv4_addr} ${invalid_netmask} ${test_gateway} ${HTTP_BAD_REQUEST}
Configure Out Of Range Netmask
[Documentation] Verify error while setting out of range netmask.
[Tags] Configure_Out_Of_Range_Netmask
[Template] Add IP Address
# ip subnet_mask gateway valid_status_codes
${test_ipv4_addr} ${out_of_range_netmask} ${test_gateway} ${HTTP_BAD_REQUEST}
Configure Alpha Netmask
[Documentation] Verify error while setting alpha netmask.
[Tags] Configure_Alpha_Netmask
[Template] Add IP Address
# ip subnet_mask gateway valid_status_codes
${test_ipv4_addr} ${alpha_netmask} ${test_gateway} ${HTTP_BAD_REQUEST}
Configure More Byte Netmask
[Documentation] Verify error while setting more byte netmask.
[Tags] Configure_More_Byte_Netmask
[Template] Add IP Address
# ip subnet_mask gateway valid_status_codes
${test_ipv4_addr} ${more_byte_netmask} ${test_gateway} ${HTTP_BAD_REQUEST}
Configure Less Byte Netmask
[Documentation] Verify error while setting less byte netmask.
[Tags] Configure_Less_Byte_Netmask
[Template] Add IP Address
# ip subnet_mask gateway valid_status_codes
${test_ipv4_addr} ${less_byte_netmask} ${test_gateway} ${HTTP_BAD_REQUEST}
Configure Threshold Netmask And Verify
[Documentation] Configure threshold netmask and verify.
[Tags] Configure_Threshold_Netmask_And_verify
[Teardown] Run Keywords
... Delete IP Address ${test_ipv4_addr} AND Test Teardown Execution
Add IP Address ${test_ipv4_addr} ${threshold_netmask} ${test_gateway}
Configure Lowest Netmask And Verify
[Documentation] Configure lowest netmask and verify.
[Tags] Configure_Lowest_Netmask_And_verify
[Teardown] Run Keywords
... Delete IP Address ${test_ipv4_addr} AND Test Teardown Execution
Add IP Address ${test_ipv4_addr} ${lowest_netmask} ${test_gateway}
Configure Network ID
[Documentation] Verify error while configuring network ID.
[Tags] Configure_Network_ID
[Template] Add IP Address
[Teardown] Clear IP Settings On Fail ${network_id}
# ip subnet_mask gateway valid_status_codes
${network_id} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST}
Configure Less Octet IP
[Documentation] Verify error while Configuring less octet IP address.
[Tags] Configure_Less_Octet_IP
[Template] Add IP Address
# ip subnet_mask gateway valid_status_codes
${less_octet_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST}
Configure Empty IP
[Documentation] Verify error while Configuring empty IP address.
[Tags] Configure_Empty_IP
[Template] Add IP Address
# ip subnet_mask gateway valid_status_codes
${EMPTY} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST}
Configure Special Char IP
[Documentation] Configure invalid IP address containing special chars.
[Tags] Configure_Special_Char_IP
[Template] Add IP Address
# ip subnet_mask gateway valid_status_codes
@@@.%%.44.11 ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST}
Configure Hexadecimal IP
[Documentation] Configure invalid IP address containing hex value.
[Tags] Configure_Hexadecimal_IP
[Template] Add IP Address
# ip subnet_mask gateway valid_status_codes
${hex_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST}
Configure Negative Octet IP
[Documentation] Configure invalid IP address containing negative octet.
[Tags] Configure_Negative_Octet_IP
[Template] Add IP Address
# ip subnet_mask gateway valid_status_codes
${negative_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST}
Configure Incomplete IP For Gateway
[Documentation] Configure incomplete IP for gateway and expect an error.
[Tags] Configure_Incomplete_IP_For_Gateway
[Template] Add IP Address
# ip subnet_mask gateway valid_status_codes
${test_ipv4_addr} ${test_subnet_mask} ${less_octet_ip} ${HTTP_BAD_REQUEST}
Configure Special Char IP For Gateway
[Documentation] Configure special char IP for gateway and expect an error.
[Tags] Configure_Special_Char_IP_For_Gateway
[Template] Add IP Address
# ip subnet_mask gateway valid_status_codes
${test_ipv4_addr} ${test_subnet_mask} @@@.%%.44.11 ${HTTP_BAD_REQUEST}
Configure Hexadecimal IP For Gateway
[Documentation] Configure hexadecimal IP for gateway and expect an error.
[Tags] Configure_Hexadecimal_IP_For_Gateway
[Template] Add IP Address
# ip subnet_mask gateway valid_status_codes
${test_ipv4_addr} ${test_subnet_mask} ${hex_ip} ${HTTP_BAD_REQUEST}
Get DNS Server And Verify
[Documentation] Get DNS server via Redfish and verify.
[Tags] Get_DNS_Server_And_Verify
Verify CLI and Redfish Nameservers
Configure DNS Server And Verify
[Documentation] Configure DNS server and verify.
[Tags] Configure_DNS_Server_And_Verify
[Setup] DNS Test Setup Execution
[Teardown] Run Keywords
... Configure Static Name Servers AND Test Teardown Execution
Configure Static Name Servers ${static_name_servers}
Verify CLI and Redfish Nameservers
Delete DNS Server And Verify
[Documentation] Delete DNS server and verify.
[Tags] Delete_DNS_Server_And_Verify
[Setup] DNS Test Setup Execution
[Teardown] Run Keywords
... Configure Static Name Servers AND Test Teardown Execution
Delete Static Name Servers
Verify CLI and Redfish Nameservers
Configure DNS Server And Check Persistency
[Documentation] Configure DNS server and check persistency on reboot.
[Tags] Configure_DNS_Server_And_Check_Persistency
[Setup] DNS Test Setup Execution
[Teardown] Run Keywords
... Configure Static Name Servers AND Test Teardown Execution
Configure Static Name Servers ${static_name_servers}
# Reboot BMC and verify persistency.
OBMC Reboot (off)
Redfish.Login
Verify CLI and Redfish Nameservers
Configure Loopback IP For Gateway
[Documentation] Configure loopback IP for gateway and expect an error.
[Tags] Configure_Loopback_IP_For_Gateway
[Template] Add IP Address
[Teardown] Clear IP Settings On Fail ${test_ipv4_addr}
# ip subnet_mask gateway valid_status_codes
${test_ipv4_addr} ${test_subnet_mask} ${loopback_ip} ${HTTP_BAD_REQUEST}
Configure Network ID For Gateway
[Documentation] Configure network ID for gateway and expect an error.
[Tags] Configure_Network_ID_For_Gateway
[Template] Add IP Address
[Teardown] Clear IP Settings On Fail ${test_ipv4_addr}
# ip subnet_mask gateway valid_status_codes
${test_ipv4_addr} ${test_subnet_mask} ${network_id} ${HTTP_BAD_REQUEST}
Configure Multicast IP For Gateway
[Documentation] Configure multicast IP for gateway and expect an error.
[Tags] Configure_Multicast_IP_For_Gateway
[Template] Add IP Address
[Teardown] Clear IP Settings On Fail ${test_ipv4_addr}
# ip subnet_mask gateway valid_status_codes
${test_ipv4_addr} ${test_subnet_mask} ${multicast_ip} ${HTTP_BAD_REQUEST}
Configure Broadcast IP For Gateway
[Documentation] Configure broadcast IP for gateway and expect an error.
[Tags] Configure_Broadcast_IP_For_Gateway
[Template] Add IP Address
[Teardown] Clear IP Settings On Fail ${test_ipv4_addr}
# ip subnet_mask gateway valid_status_codes
${test_ipv4_addr} ${test_subnet_mask} ${broadcast_ip} ${HTTP_BAD_REQUEST}
Configure Null Value For DNS Server
[Documentation] Configure null value for DNS server and expect an error.
[Tags] Configure_Null_Value_For_DNS_Server
[Setup] DNS Test Setup Execution
[Teardown] Run Keywords
... Configure Static Name Servers AND Test Teardown Execution
Configure Static Name Servers ${null_value} ${HTTP_BAD_REQUEST}
Configure Empty Value For DNS Server
[Documentation] Configure empty value for DNS server and expect an error.
[Tags] Configure_Empty_Value_For_DNS_Server
[Setup] DNS Test Setup Execution
[Teardown] Run Keywords
... Configure Static Name Servers AND Test Teardown Execution
Configure Static Name Servers ${empty_dictionary} ${HTTP_BAD_REQUEST}
Configure String Value For DNS Server
[Documentation] Configure string value for DNS server and expect an error.
[Tags] Configure_String_Value_For_DNS_Server
[Setup] DNS Test Setup Execution
[Teardown] Run Keywords
... Configure Static Name Servers AND Test Teardown Execution
Configure Static Name Servers ${string_value} ${HTTP_BAD_REQUEST}
Modify IPv4 Address And Verify
[Documentation] Modify IP address via Redfish and verify.
[Tags] Modify_IPv4_Addres_And_Verify
[Teardown] Run Keywords
... Delete IP Address ${test_ipv4_addr2} AND Test Teardown Execution
Add IP Address ${test_ipv4_addr} ${test_subnet_mask} ${test_gateway}
Update IP Address ${test_ipv4_addr} ${test_ipv4_addr2} ${test_subnet_mask} ${test_gateway}
Configure Invalid Values For DNS Server
[Documentation] Configure invalid values for DNS server and expect an error.
[Tags] Configure_Invalid_Value_For_DNS_Server
[Setup] DNS Test Setup Execution
[Template] Configure Static Name Servers
[Teardown] Run Keywords
... Configure Static Name Servers AND Test Teardown Execution
# static_name_servers valid_status_codes
0xa.0xb.0xc.0xd ${HTTP_BAD_REQUEST}
10.-7.-7.-7 ${HTTP_BAD_REQUEST}
10.3.36 ${HTTP_BAD_REQUEST}
@@@.%%.44.11 ${HTTP_BAD_REQUEST}
Config Multiple DNS Servers And Verify
[Documentation] Config multiple DNS servers and verify.
[Tags] Config_Multiple_DNS_Servers_And_Verify
[Setup] DNS Test Setup Execution
[Teardown] Run Keywords
... Configure Static Name Servers AND Test Teardown Execution
@{list_name_servers}= Create List 10.5.5.10 10.20.5.10 10.5.6.7
Configure Static Name Servers ${list_name_servers}
Verify CLI and Redfish Nameservers
Configure And Verify Multiple Static IPv4 Addresses
[Documentation] Configure multiple static ipv4 address via Redfish and verify.
[Tags] Configure_And_Verify_Multiple_Static_IPv4_Addresses
[Teardown] Run Keywords Delete Multiple Static IPv4 Addresses ${test_ipv4_addresses}
... AND Test Teardown Execution
${test_ipv4_addresses}= Create List ${test_ipv4_addr} ${test_ipv4_addr2}
Configure Multiple Static IPv4 Addresses ${test_ipv4_addresses} ${test_subnet_mask} ${test_gateway}
Configure Multiple Static IPv4 Addresses And Check Persistency
[Documentation] Configure multiple static ipv4 address via Redfish and check persistency.
[Tags] Configure_Multiple_Static_IPv4_Addresses_And_Check_Persistency
[Teardown] Run Keywords Delete Multiple Static IPv4 Addresses ${test_ipv4_addresses}
... AND Test Teardown Execution
${test_ipv4_addresses}= Create List ${test_ipv4_addr} ${test_ipv4_addr2}
Configure Multiple Static IPv4 Addresses ${test_ipv4_addresses} ${test_subnet_mask} ${test_gateway}
# Reboot BMC and verify persistency.
OBMC Reboot (off)
Redfish.Login
FOR ${ip} IN @{test_ipv4_addresses}
Verify IP And Netmask On BMC ${ip} ${test_subnet_mask}
END
Configure And Verify Multiple IPv4 Addresses
[Documentation] Configure multiple IPv4 addresses and verify.
[Tags] Configure_And_Verify_Multiple_IPv4_Addresse
[Teardown] Run Keywords
... Delete IP Address ${test_ipv4_addr} AND Delete IP Address ${test_ipv4_addr2}
... AND Test Teardown Execution
${ip1}= Create dictionary Address=${test_ipv4_addr}
... SubnetMask=255.255.0.0 Gateway=${test_gateway}
${ip2}= Create dictionary Address=${test_ipv4_addr2}
... SubnetMask=255.255.252.0 Gateway=${test_gateway}
${empty_dict}= Create Dictionary
${patch_list}= Create List
${network_configurations}= Get Network Configuration
${num_entries}= Get Length ${network_configurations}
FOR ${INDEX} IN RANGE 0 ${num_entries}
Append To List ${patch_list} ${empty_dict}
END
# We need not check for existence of IP on BMC while adding.
Append To List ${patch_list} ${ip1} ${ip2}
${payload}= Create Dictionary IPv4StaticAddresses=${patch_list}
${active_channel_config}= Get Active Channel Config
${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']}
Redfish.patch ${REDFISH_NW_ETH_IFACE}${ethernet_interface} body=&{payload}
... valid_status_codes=[${HTTP_OK}, ${HTTP_NO_CONTENT}]
# Note: Network restart takes around 15-18s after patch request processing.
Sleep ${NETWORK_TIMEOUT}s
Wait For Host To Ping ${OPENBMC_HOST} ${NETWORK_TIMEOUT}
Verify IP On BMC ${test_ipv4_addr}
Verify IP On BMC ${test_ipv4_addr2}
Config Multiple DNS Servers And Check Persistency
[Documentation] Config multiple DNS and check persistency.
[Tags] Config_Multiple_DNS_Servers_And_Check_Persistency
[Setup] DNS Test Setup Execution
[Teardown] Run Keywords
... Configure Static Name Servers AND Test Teardown Execution
@{list_name_servers}= Create List 10.5.5.10 10.20.5.10 10.5.6.7
Configure Static Name Servers ${list_name_servers}
# Reboot BMC and verify persistency.
OBMC Reboot (off)
Redfish.Login
Verify CLI and Redfish Nameservers
Configure Static IP Without Using Gateway And Verify
[Documentation] Configure static IP without using gateway and verify error.
[Tags] Configure_Static_IP_Without_Using_Gateway_And_Verify
${ip}= Create dictionary Address=${test_ipv4_addr}
... SubnetMask=${test_subnet_mask}
${empty_dict}= Create Dictionary
${patch_list}= Create List
${network_configurations}= Get Network Configuration
${num_entries}= Get Length ${network_configurations}
FOR ${INDEX} IN RANGE 0 ${num_entries}
Append To List ${patch_list} ${empty_dict}
END
# We need not check for existence of IP on BMC while adding.
Append To List ${patch_list} ${ip}
${payload}= Create Dictionary IPv4StaticAddresses=${patch_list}
${active_channel_config}= Get Active Channel Config
${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']}
Redfish.patch ${REDFISH_NW_ETH_IFACE}${ethernet_interface}
... body=&{payload} valid_status_codes=[${HTTP_BAD_REQUEST}]
Test Network Response On Specified Host State
[Documentation] Verifying the BMC network response when host is on and off.
[Tags] Test_Network_Response_On_Specified_Host_State
[Template] Verify Network Response On Specified Host State
# host_state
on
off
*** Keywords ***
Test Setup Execution
[Documentation] Test setup execution.
Redfish.Login
@{network_configurations}= Get Network Configuration
Set Test Variable @{network_configurations}
# Get BMC IP address and prefix length.
${ip_data}= Get BMC IP Info
Set Test Variable ${ip_data}
Verify Netmask On BMC
[Documentation] Verify netmask on BMC.
[Arguments] ${netmask}
# Description of the argument(s):
# netmask netmask value to be verified.
${prefix_length}= Netmask Prefix Length ${netmask}
Should Contain Match ${ip_data} */${prefix_length}
... msg=Prefix length does not exist.
Verify IP And Netmask On BMC
[Documentation] Verify IP and netmask on BMC.
[Arguments] ${ip} ${netmask}
# Description of the argument(s):
# ip IP address to be verified.
# netmask netmask value to be verified.
${prefix_length}= Netmask Prefix Length ${netmask}
@{ip_data}= Get BMC IP Info
${ip_with_netmask}= Catenate ${ip}/${prefix_length}
Should Contain ${ip_data} ${ip_with_netmask}
... msg=IP and netmask pair does not exist.
Test Teardown Execution
[Documentation] Test teardown execution.
FFDC On Test Case Fail
Redfish.Logout
Clear IP Settings On Fail
[Documentation] Clear IP settings on fail.
[Arguments] ${ip}
# Description of argument(s):
# ip IP address to be deleted.
Run Keyword If '${TEST STATUS}' == 'FAIL'
... Delete IP Address ${ip}
Test Teardown Execution
Verify CLI and Redfish Nameservers
[Documentation] Verify that nameservers obtained via Redfish do not
... match those found in /etc/resolv.conf.
${active_channel_config}= Get Active Channel Config
${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']}
${redfish_nameservers}= Redfish.Get Attribute
... ${REDFISH_NW_ETH_IFACE}${ethernet_interface} StaticNameServers
${resolve_conf_nameservers}= CLI Get Nameservers
Rqprint Vars redfish_nameservers resolve_conf_nameservers
List Should Contain Sub List ${resolve_conf_nameservers} ${redfish_nameservers}
... msg=The nameservers obtained via Redfish do not match those found in /etc/resolv.conf.
Configure Static Name Servers
[Documentation] Configure DNS server on BMC.
[Arguments] ${static_name_servers}=${original_nameservers}
... ${valid_status_codes}=${HTTP_OK}
# Description of the argument(s):
# static_name_servers A list of static name server IPs to be
# configured on the BMC.
${active_channel_config}= Get Active Channel Config
${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']}
${type} = Evaluate type($static_name_servers).__name__
${static_name_servers}= Set Variable If '${type}'=='str'
... '${static_name_servers}' ${static_name_servers}
# Currently BMC is sending 500 response code instead of 400 for invalid scenarios.
Redfish.Patch ${REDFISH_NW_ETH_IFACE}${ethernet_interface}
... body={'StaticNameServers': ${static_name_servers}}
... valid_status_codes=[${valid_status_codes}, ${HTTP_INTERNAL_SERVER_ERROR}]
# Patch operation takes 1 to 3 seconds to set new value.
Sleep 3s
# Check if newly added DNS server is configured on BMC.
${cli_nameservers}= CLI Get Nameservers
${cmd_status}= Run Keyword And Return Status
... List Should Contain Sub List ${cli_nameservers} ${static_name_servers}
Run Keyword If '${valid_status_codes}' == '${HTTP_OK}'
... Should Be True ${cmd_status} == ${True}
... ELSE Should Be True ${cmd_status} == ${False}
Delete Static Name Servers
[Documentation] Delete static name servers.
Configure Static Name Servers static_name_servers=@{EMPTY}
# Check if all name servers deleted on BMC.
${nameservers}= CLI Get Nameservers
Should Be Empty ${nameservers}
DNS Test Setup Execution
[Documentation] Do DNS test setup execution.
Redfish.Login
${active_channel_config}= Get Active Channel Config
${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']}
${original_nameservers}= Redfish.Get Attribute
... ${REDFISH_NW_ETH_IFACE}${ethernet_interface} StaticNameServers
Rprint Vars original_nameservers
# Set suite variables to trigger restoration during teardown.
Set Suite Variable ${original_nameservers}
Suite Setup Execution
[Documentation] Do suite setup execution.
${test_gateway}= Get BMC Default Gateway
Set Suite Variable ${test_gateway}
Update IP Address
[Documentation] Update IP address of BMC.
[Arguments] ${ip} ${new_ip} ${netmask} ${gw_ip}
... ${valid_status_codes}=[${HTTP_OK}, ${HTTP_NO_CONTENT}]
# Description of argument(s):
# ip IP address to be replaced (e.g. "10.7.7.7").
# new_ip New IP address to be configured.
# netmask Netmask value.
# gw_ip Gateway IP address.
# valid_status_codes Expected return code from patch operation
# (e.g. "200"). See prolog of rest_request
# method in redfish_plus.py for details.
${empty_dict}= Create Dictionary
${patch_list}= Create List
${ip_data}= Create Dictionary Address=${new_ip} SubnetMask=${netmask} Gateway=${gw_ip}
# Find the position of IP address to be modified.
@{network_configurations}= Get Network Configuration
FOR ${network_configuration} IN @{network_configurations}
Run Keyword If '${network_configuration['Address']}' == '${ip}'
... Append To List ${patch_list} ${ip_data}
... ELSE Append To List ${patch_list} ${empty_dict}
END
${ip_found}= Run Keyword And Return Status List Should Contain Value
... ${patch_list} ${ip_data} msg=${ip} does not exist on BMC
Pass Execution If ${ip_found} == ${False} ${ip} does not exist on BMC
# Run patch command only if given IP is found on BMC
${data}= Create Dictionary IPv4StaticAddresses=${patch_list}
${active_channel_config}= Get Active Channel Config
${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']}
Redfish.patch ${REDFISH_NW_ETH_IFACE}${ethernet_interface}
... body=&{data} valid_status_codes=${valid_status_codes}
# Note: Network restart takes around 15-18s after patch request processing.
Sleep ${NETWORK_TIMEOUT}s
Wait For Host To Ping ${OPENBMC_HOST} ${NETWORK_TIMEOUT}
Verify IP On BMC ${new_ip}
Validate Network Config On BMC
Configure Multiple Static IPv4 Addresses
[Documentation] Configure multiple static ipv4 address via Redfish and verify.
[Arguments] ${ip_addreses} ${subnet_mask} ${gateway}
# Description of argument(s):
# ip_addreses A list of IP addresses to be added (e.g.["10.7.7.7"]).
# subnet_mask Subnet mask for the IP to be added (e.g. "255.255.0.0").
# gateway Gateway for the IP to be added (e.g. "10.7.7.1").
FOR ${ip} IN @{ip_addreses}
Add IP Address ${ip} ${subnet_mask} ${gateway}
END
Validate Network Config On BMC
Delete Multiple Static IPv4 Addresses
[Documentation] Delete multiple static ipv4 address via Redfish.
[Arguments] ${ip_addreses}
# Description of argument(s):
# ip_addreses A list of IP addresses to be deleted (e.g.["10.7.7.7"]).
FOR ${ip} IN @{ip_addreses}
Delete IP Address ${ip}
END
Validate Network Config On BMC
Verify Network Response On Specified Host State
[Documentation] Verifying the BMC network response when host is on and off.
[Arguments] ${host_state}
# Description of argument(s):
# host_state if host_state is on then host is booted to operating system.
# if host_state is off then host is power off.
# (eg. on, off).
${active_channel_config}= Get Active Channel Config
${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']}
Run Keyword If '${host_state}' == 'on'
... Redfish Power On stack_mode=skip
... ELSE
... Redfish Power off stack_mode=skip
Redfish.Get ${REDFISH_NW_ETH_IFACE}${ethernet_interface}
Ping Host ${OPENBMC_HOST}