| *** Settings *** |
| Documentation Network interface configuration and verification |
| ... tests. |
| |
| Resource ../../lib/bmc_redfish_resource.robot |
| Resource ../../lib/bmc_network_utils.robot |
| Resource ../../lib/openbmc_ffdc.robot |
| Library ../../lib/bmc_network_utils.py |
| Library Collections |
| |
| Test Setup Test Setup Execution |
| Test Teardown Test Teardown Execution |
| |
| Force Tags Network_Conf_Test |
| |
| *** Variables *** |
| ${test_hostname} openbmc |
| ${test_ipv4_addr} 10.7.7.7 |
| ${test_ipv4_invalid_addr} 0.0.1.a |
| ${test_subnet_mask} 255.255.0.0 |
| ${test_gateway} 10.7.7.1 |
| ${broadcast_ip} 10.7.7.255 |
| ${loopback_ip} 127.0.0.2 |
| ${multicast_ip} 224.6.6.6 |
| ${out_of_range_ip} 10.7.7.256 |
| |
| # Valid netmask is 4 bytes long and has continuos block of 1s. |
| # Maximum valid value in each octet is 255 and least value is 0. |
| # 253 is not valid, as binary value is 11111101. |
| ${invalid_netmask} 255.255.253.0 |
| ${alpha_netmask} ff.ff.ff.ff |
| # Maximum value of octet in netmask is 255. |
| ${out_of_range_netmask} 255.256.255.0 |
| ${more_byte_netmask} 255.255.255.0.0 |
| ${less_byte_netmask} 255.255.255 |
| ${threshold_netmask} 255.255.255.255 |
| ${lowest_netmask} 128.0.0.0 |
| |
| # There will be 4 octets in IP address (e.g. xx.xx.xx.xx) |
| # but trying to configure xx.xx.xx |
| ${less_octet_ip} 10.3.36 |
| |
| # For the address 10.6.6.6, the 10.6.6.0 portion describes the |
| # network ID and the 6 describe the host. |
| |
| ${network_id} 10.7.7.0 |
| ${hex_ip} 0xa.0xb.0xc.0xd |
| ${negative_ip} 10.-7.-7.7 |
| ${hex_ip} 0xa.0xb.0xc.0xd |
| @{static_name_servers} 10.5.5.5 |
| |
| *** Test Cases *** |
| |
| Get IP Address And Verify |
| [Documentation] Get IP Address And Verify. |
| [Tags] Get_IP_Address_And_Verify |
| |
| : FOR ${network_configuration} IN @{network_configurations} |
| \ Verify IP On BMC ${network_configuration['Address']} |
| |
| Get Netmask And Verify |
| [Documentation] Get Netmask And Verify. |
| [Tags] Get_Netmask_And_Verify |
| |
| : FOR ${network_configuration} IN @{network_configurations} |
| \ Verify Netmask On BMC ${network_configuration['SubnetMask']} |
| |
| Get Gateway And Verify |
| [Documentation] Get gateway and verify it's existence on the BMC. |
| [Tags] Get_Gateway_And_Verify |
| |
| : FOR ${network_configuration} IN @{network_configurations} |
| \ Verify Gateway On BMC ${network_configuration['Gateway']} |
| |
| Get MAC Address And Verify |
| [Documentation] Get MAC address and verify it's existence on the BMC. |
| [Tags] Get_MAC_Address_And_Verify |
| |
| ${resp}= Redfish.Get ${REDFISH_NW_ETH0_URI} |
| ${macaddr}= Get From Dictionary ${resp.dict} MACAddress |
| Validate MAC On BMC ${macaddr} |
| |
| Verify All Configured IP And Netmask |
| [Documentation] Verify all configured IP and netmask on BMC. |
| [Tags] Verify_All_Configured_IP_And_Netmask |
| |
| : FOR ${network_configuration} IN @{network_configurations} |
| \ Verify IP And Netmask On BMC ${network_configuration['Address']} |
| ... ${network_configuration['SubnetMask']} |
| |
| Get Hostname And Verify |
| [Documentation] Get hostname via Redfish and verify. |
| [Tags] Get_Hostname_And_Verify |
| |
| ${hostname}= Redfish_Utils.Get Attribute ${REDFISH_NW_PROTOCOL_URI} HostName |
| |
| Validate Hostname On BMC ${hostname} |
| |
| Configure Hostname And Verify |
| [Documentation] Configure hostname via Redfish and verify. |
| [Tags] Configure_Hostname_And_Verify |
| |
| ${hostname}= Redfish_Utils.Get Attribute ${REDFISH_NW_PROTOCOL_URI} HostName |
| |
| Configure Hostname ${test_hostname} |
| Validate Hostname On BMC ${test_hostname} |
| |
| # Revert back to initial hostname. |
| Configure Hostname ${hostname} |
| Validate Hostname On BMC ${hostname} |
| |
| Add Valid IPv4 Address And Verify |
| [Documentation] Add IPv4 Address via Redfish and verify. |
| [Tags] Add_Valid_IPv4_Addres_And_Verify |
| |
| Add IP Address ${test_ipv4_addr} ${test_subnet_mask} ${test_gateway} |
| Delete IP Address ${test_ipv4_addr} |
| |
| Add Invalid IPv4 Address And Verify |
| [Documentation] Add Invalid IPv4 Address via Redfish and verify. |
| [Tags] Add_Invalid_IPv4_Addres_And_Verify |
| |
| Add IP Address ${test_ipv4_invalid_addr} ${test_subnet_mask} |
| ... ${test_gateway} valid_status_codes=${HTTP_BAD_REQUEST} |
| |
| Configure Out Of Range IP |
| [Documentation] Configure out-of-range IP address. |
| [Tags] Configure_Out_Of_Range_IP |
| [Template] Add IP Address |
| |
| # ip subnet_mask gateway valid_status_codes |
| ${out_of_range_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} |
| |
| Configure Broadcast IP |
| [Documentation] Configure broadcast IP address. |
| [Tags] Configure_Broadcast_IP |
| [Template] Add IP Address |
| [Teardown] Clear IP Settings On Fail ${broadcast_ip} |
| |
| # ip subnet_mask gateway valid_status_codes |
| ${broadcast_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} |
| |
| Configure Multicast IP |
| [Documentation] Configure multicast IP address. |
| [Tags] Configure_Multicast_IP |
| [Template] Add IP Address |
| [Teardown] Clear IP Settings On Fail ${multicast_ip} |
| |
| # ip subnet_mask gateway valid_status_codes |
| ${multicast_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} |
| |
| Configure Loopback IP |
| [Documentation] Configure loopback IP address. |
| [Tags] Configure_Loopback_IP |
| [Template] Add IP Address |
| [Teardown] Clear IP Settings On Fail ${loopback_ip} |
| |
| # ip subnet_mask gateway valid_status_codes |
| ${loopback_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} |
| |
| Add Valid IPv4 Address And Check Persistency |
| [Documentation] Add IPv4 address and check peristency. |
| [Tags] Add_Valid_IPv4_Addres_And_Check_Persistency |
| |
| Add IP Address ${test_ipv4_addr} ${test_subnet_mask} ${test_gateway} |
| |
| # Reboot BMC and verify persistency. |
| OBMC Reboot (off) |
| Verify IP On BMC ${test_ipv4_addr} |
| Delete IP Address ${test_ipv4_addr} |
| |
| Add Fourth Octet Threshold IP And Verify |
| [Documentation] Add fourth octet threshold IP and verify. |
| [Tags] Add_Fourth_Octet_Threshold_IP_And_Verify |
| |
| Add IP Address 10.7.7.254 ${test_subnet_mask} ${test_gateway} |
| Delete IP Address 10.7.7.254 |
| |
| Add Fourth Octet Lowest IP And Verify |
| [Documentation] Add fourth octet lowest IP and verify. |
| [Tags] Add_Fourth_Octet_Lowest_IP_And_Verify |
| |
| Add IP Address 10.7.7.1 ${test_subnet_mask} ${test_gateway} |
| Delete IP Address 10.7.7.1 |
| |
| Add Third Octet Threshold IP And Verify |
| [Documentation] Add third octet threshold IP and verify. |
| [Tags] Add_Third_Octet_Threshold_IP_And_Verify |
| |
| Add IP Address 10.7.255.7 ${test_subnet_mask} ${test_gateway} |
| Delete IP Address 10.7.255.7 |
| |
| Add Third Octet Lowest IP And Verify |
| [Documentation] Add third octet lowest IP and verify. |
| [Tags] Add_Third_Octet_Lowest_IP_And_Verify |
| |
| Add IP Address 10.7.0.7 ${test_subnet_mask} ${test_gateway} |
| Delete IP Address 10.7.0.7 |
| |
| Add Second Octet Threshold IP And Verify |
| [Documentation] Add second octet threshold IP and verify. |
| [Tags] Add_Second_Octet_Threshold_IP_And_Verify |
| |
| Add IP Address 10.255.7.7 ${test_subnet_mask} ${test_gateway} |
| Delete IP Address 10.255.7.7 |
| |
| Add Second Octet Lowest IP And Verify |
| [Documentation] Add second octet lowest IP and verify. |
| [Tags] Add_Second_Octet_Lowest_IP_And_Verify |
| |
| Add IP Address 10.0.7.7 ${test_subnet_mask} ${test_gateway} |
| Delete IP Address 10.0.7.7 |
| |
| Add First Octet Threshold IP And Verify |
| [Documentation] Add first octet threshold IP and verify. |
| [Tags] Add_First_Octet_Threshold_IP_And_Verify |
| |
| Add IP Address 223.7.7.7 ${test_subnet_mask} ${test_gateway} |
| Delete IP Address 223.7.7.7 |
| |
| Add First Octet Lowest IP And Verify |
| [Documentation] Add first octet lowest IP and verify. |
| [Tags] Add_First_Octet_Lowest_IP_And_Verify |
| |
| Add IP Address 1.7.7.7 ${test_subnet_mask} ${test_gateway} |
| Delete IP Address 1.7.7.7 |
| |
| Configure Invalid Netmask |
| [Documentation] Verify error while setting invalid netmask. |
| [Tags] Configure_Invalid_Netmask |
| [Template] Add IP Address |
| |
| # ip subnet_mask gateway valid_status_codes |
| ${test_ipv4_addr} ${invalid_netmask} ${test_gateway} ${HTTP_BAD_REQUEST} |
| |
| Configure Out Of Range Netmask |
| [Documentation] Verify error while setting out of range netmask. |
| [Tags] Configure_Out_Of_Range_Netmask |
| [Template] Add IP Address |
| |
| # ip subnet_mask gateway valid_status_codes |
| ${test_ipv4_addr} ${out_of_range_netmask} ${test_gateway} ${HTTP_BAD_REQUEST} |
| |
| Configure Alpha Netmask |
| [Documentation] Verify error while setting alpha netmask. |
| [Tags] Configure_Alpha_Netmask |
| [Template] Add IP Address |
| |
| # ip subnet_mask gateway valid_status_codes |
| ${test_ipv4_addr} ${alpha_netmask} ${test_gateway} ${HTTP_BAD_REQUEST} |
| |
| Configure More Byte Netmask |
| [Documentation] Verify error while setting more byte netmask. |
| [Tags] Configure_More_Byte_Netmask |
| [Template] Add IP Address |
| |
| # ip subnet_mask gateway valid_status_codes |
| ${test_ipv4_addr} ${more_byte_netmask} ${test_gateway} ${HTTP_BAD_REQUEST} |
| |
| Configure Less Byte Netmask |
| [Documentation] Verify error while setting less byte netmask. |
| [Tags] Configure_Less_Byte_Netmask |
| [Template] Add IP Address |
| |
| # ip subnet_mask gateway valid_status_codes |
| ${test_ipv4_addr} ${less_byte_netmask} ${test_gateway} ${HTTP_BAD_REQUEST} |
| |
| Configure Threshold Netmask And Verify |
| [Documentation] Configure threshold netmask and verify. |
| [Tags] Configure_Threshold_Netmask_And_verify |
| |
| Add IP Address ${test_ipv4_addr} ${threshold_netmask} ${test_gateway} |
| Delete IP Address ${test_ipv4_addr} |
| |
| Configure Lowest Netmask And Verify |
| [Documentation] Configure lowest netmask and verify. |
| [Tags] Configure_Lowest_Netmask_And_verify |
| |
| Add IP Address ${test_ipv4_addr} ${lowest_netmask} ${test_gateway} |
| Delete IP Address ${test_ipv4_addr} |
| |
| Configure Network ID |
| [Documentation] Verify error while configuring network ID. |
| [Tags] Configure_Network_ID |
| [Template] Add IP Address |
| [Teardown] Clear IP Settings On Fail ${network_id} |
| |
| # ip subnet_mask gateway valid_status_codes |
| ${network_id} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} |
| |
| Configure Less Octet IP |
| [Documentation] Verify error while Configuring less octet IP address. |
| [Tags] Configure_Less_Octet_IP |
| [Template] Add IP Address |
| |
| # ip subnet_mask gateway valid_status_codes |
| ${less_octet_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} |
| |
| Configure Empty IP |
| [Documentation] Verify error while Configuring empty IP address. |
| [Tags] Configure_Empty_IP |
| [Template] Add IP Address |
| |
| # ip subnet_mask gateway valid_status_codes |
| ${EMPTY} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} |
| |
| Configure Special Char IP |
| [Documentation] Configure invalid IP address containing special chars. |
| [Tags] Configure_Special_Char_IP |
| [Template] Add IP Address |
| |
| # ip subnet_mask gateway valid_status_codes |
| @@@.%%.44.11 ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} |
| |
| Configure Hexadecimal IP |
| [Documentation] Configure invalid IP address containing hex value. |
| [Tags] Configure_Hexadecimal_IP |
| [Template] Add IP Address |
| |
| # ip subnet_mask gateway valid_status_codes |
| ${hex_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} |
| |
| Configure Negative Octet IP |
| [Documentation] Configure invalid IP address containing negative octet. |
| [Tags] Configure_Negative_Octet_IP |
| [Template] Add IP Address |
| |
| # ip subnet_mask gateway valid_status_codes |
| ${negative_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} |
| |
| Configure Incomplete IP For Gateway |
| [Documentation] Configure incomplete IP for gateway and expect an error. |
| [Tags] Configure_Incomplete_IP_For_Gateway |
| [Template] Add IP Address |
| |
| # ip subnet_mask gateway valid_status_codes |
| ${test_ipv4_addr} ${test_subnet_mask} ${less_octet_ip} ${HTTP_BAD_REQUEST} |
| |
| Configure Special Char IP For Gateway |
| [Documentation] Configure special char IP for gateway and expect an error. |
| [Tags] Configure_Special_Char_IP_For_Gateway |
| [Template] Add IP Address |
| |
| # ip subnet_mask gateway valid_status_codes |
| ${test_ipv4_addr} ${test_subnet_mask} @@@.%%.44.11 ${HTTP_BAD_REQUEST} |
| |
| Configure Hexadecimal IP For Gateway |
| [Documentation] Configure hexadecimal IP for gateway and expect an error. |
| [Tags] Configure_Hexadecimal_IP_For_Gateway |
| [Template] Add IP Address |
| |
| # ip subnet_mask gateway valid_status_codes |
| ${test_ipv4_addr} ${test_subnet_mask} ${hex_ip} ${HTTP_BAD_REQUEST} |
| |
| Get DNS Server And Verify |
| [Documentation] Get DNS server via Redfish and verify. |
| [Tags] Get_DNS_Server_And_Verify |
| |
| Verify CLI and Redfish Nameservers |
| |
| Configure DNS Server And Verify |
| [Documentation] Configure DNS server and verify. |
| [Tags] Configure_DNS_Server_And_Verify |
| [Teardown] Run Keywords |
| ... Configure Static Name Servers AND Test Teardown Execution |
| |
| ${original_redfish_nameservers}= Redfish.Get Attribute ${REDFISH_NW_ETH0_URI} StaticNameServers |
| Rprint Vars original_redfish_nameservers |
| # Set suite variables to trigger restoration during teardown. |
| Set Suite Variable ${original_redfish_nameservers} |
| |
| Configure Static Name Servers ${static_name_servers} |
| Verify CLI and Redfish Nameservers |
| |
| *** Keywords *** |
| |
| Test Setup Execution |
| [Documentation] Test setup execution. |
| |
| Redfish.Login |
| |
| @{network_configurations}= Get Network Configuration |
| Set Test Variable @{network_configurations} |
| |
| # Get BMC IP address and prefix length. |
| ${ip_data}= Get BMC IP Info |
| Set Test Variable ${ip_data} |
| |
| |
| Get Network Configuration |
| [Documentation] Get network configuration. |
| |
| # Sample output: |
| #{ |
| # "@odata.context": "/redfish/v1/$metadata#EthernetInterface.EthernetInterface", |
| # "@odata.id": "/redfish/v1/Managers/bmc/EthernetInterfaces/eth0", |
| # "@odata.type": "#EthernetInterface.v1_2_0.EthernetInterface", |
| # "Description": "Management Network Interface", |
| # "IPv4Addresses": [ |
| # { |
| # "Address": "169.254.xx.xx", |
| # "AddressOrigin": "IPv4LinkLocal", |
| # "Gateway": "0.0.0.0", |
| # "SubnetMask": "255.255.0.0" |
| # }, |
| # { |
| # "Address": "xx.xx.xx.xx", |
| # "AddressOrigin": "Static", |
| # "Gateway": "xx.xx.xx.1", |
| # "SubnetMask": "xx.xx.xx.xx" |
| # } |
| # ], |
| # "Id": "eth0", |
| # "MACAddress": "xx:xx:xx:xx:xx:xx", |
| # "Name": "Manager Ethernet Interface", |
| # "SpeedMbps": 0, |
| # "VLAN": { |
| # "VLANEnable": false, |
| # "VLANId": 0 |
| # } |
| |
| ${resp}= Redfish.Get ${REDFISH_NW_ETH0_URI} |
| @{network_configurations}= Get From Dictionary ${resp.dict} IPv4StaticAddresses |
| [Return] @{network_configurations} |
| |
| |
| Verify IP On BMC |
| [Documentation] Verify IP on BMC. |
| [Arguments] ${ip} |
| |
| # Description of argument(s): |
| # ip IP address to be verified (e.g. "10.7.7.7"). |
| |
| # Get IP address details on BMC using IP command. |
| @{ip_data}= Get BMC IP Info |
| Should Contain Match ${ip_data} ${ip}/* |
| ... msg=IP address does not exist. |
| |
| Add IP Address |
| [Documentation] Add IP Address To BMC. |
| [Arguments] ${ip} ${subnet_mask} ${gateway} |
| ... ${valid_status_codes}=${HTTP_OK} |
| |
| # Description of argument(s): |
| # ip IP address to be added (e.g. "10.7.7.7"). |
| # subnet_mask Subnet mask for the IP to be added |
| # (e.g. "255.255.0.0"). |
| # gateway Gateway for the IP to be added (e.g. "10.7.7.1"). |
| # valid_status_codes Expected return code from patch operation |
| # (e.g. "200"). See prolog of rest_request |
| # method in redfish_plut.py for details. |
| |
| ${empty_dict}= Create Dictionary |
| ${ip_data}= Create Dictionary Address=${ip} |
| ... SubnetMask=${subnet_mask} Gateway=${gateway} |
| |
| ${patch_list}= Create List |
| ${network_configurations}= Get Network Configuration |
| ${num_entries}= Get Length ${network_configurations} |
| |
| : FOR ${INDEX} IN RANGE 0 ${num_entries} |
| \ Append To List ${patch_list} ${empty_dict} |
| |
| # We need not check for existence of IP on BMC while adding. |
| Append To List ${patch_list} ${ip_data} |
| ${data}= Create Dictionary IPv4StaticAddresses=${patch_list} |
| |
| Redfish.patch ${REDFISH_NW_ETH0_URI} body=&{data} |
| ... valid_status_codes=[${valid_status_codes}] |
| |
| Return From Keyword If '${valid_status_codes}' != '${HTTP_OK}' |
| |
| # Note: Network restart takes around 15-18s after patch request processing. |
| Sleep ${NETWORK_TIMEOUT}s |
| Wait For Host To Ping ${OPENBMC_HOST} ${NETWORK_TIMEOUT} |
| |
| Verify IP On BMC ${ip} |
| Validate Network Config On BMC |
| |
| |
| Delete IP Address |
| [Documentation] Delete IP Address Of BMC. |
| [Arguments] ${ip} ${valid_status_codes}=${HTTP_OK} |
| |
| # Description of argument(s): |
| # ip IP address to be deleted (e.g. "10.7.7.7"). |
| # valid_status_codes Expected return code from patch operation |
| # (e.g. "200"). See prolog of rest_request |
| # method in redfish_plut.py for details. |
| |
| ${empty_dict}= Create Dictionary |
| ${patch_list}= Create List |
| |
| @{network_configurations}= Get Network Configuration |
| : FOR ${network_configuration} IN @{network_configurations} |
| \ Run Keyword If '${network_configuration['Address']}' == '${ip}' |
| ... Append To List ${patch_list} ${null} |
| ... ELSE Append To List ${patch_list} ${empty_dict} |
| |
| ${ip_found}= Run Keyword And Return Status List Should Contain Value |
| ... ${patch_list} ${null} msg=${ip} does not exist on BMC |
| Pass Execution If ${ip_found} == ${False} ${ip} does not exist on BMC |
| |
| # Run patch command only if given IP is found on BMC |
| ${data}= Create Dictionary IPv4StaticAddresses=${patch_list} |
| |
| Redfish.patch ${REDFISH_NW_ETH0_URI} body=&{data} |
| ... valid_status_codes=[${valid_status_codes}] |
| |
| # Note: Network restart takes around 15-18s after patch request processing |
| Sleep ${NETWORK_TIMEOUT}s |
| Wait For Host To Ping ${OPENBMC_HOST} ${NETWORK_TIMEOUT} |
| |
| ${delete_status}= Run Keyword And Return Status Verify IP On BMC ${ip} |
| Run Keyword If '${valid_status_codes}' == '${HTTP_OK}' |
| ... Should Be True ${delete_status} == ${False} |
| ... ELSE Should Be True ${delete_status} == ${True} |
| |
| Validate Network Config On BMC |
| |
| |
| Validate Network Config On BMC |
| [Documentation] Check that network info obtained via redfish matches info |
| ... obtained via CLI. |
| |
| @{network_configurations}= Get Network Configuration |
| ${ip_data}= Get BMC IP Info |
| : FOR ${network_configuration} IN @{network_configurations} |
| \ Should Contain Match ${ip_data} ${network_configuration['Address']}/* |
| ... msg=IP address does not exist. |
| |
| |
| Verify Netmask On BMC |
| [Documentation] Verify netmask on BMC. |
| [Arguments] ${netmask} |
| |
| # Description of the argument(s): |
| # netmask netmask value to be verified. |
| |
| ${prefix_length}= Netmask Prefix Length ${netmask} |
| |
| Should Contain Match ${ip_data} */${prefix_length} |
| ... msg=Prefix length does not exist. |
| |
| Verify Gateway On BMC |
| [Documentation] Verify gateway on BMC. |
| [Arguments] ${gateway_ip}=0.0.0.0 |
| |
| # Description of argument(s): |
| # gateway_ip Gateway IP address. |
| |
| ${route_info}= Get BMC Route Info |
| |
| # If gateway IP is empty or 0.0.0.0 it will not have route entry. |
| |
| Run Keyword If '${gateway_ip}' == '0.0.0.0' |
| ... Pass Execution Gateway IP is "0.0.0.0". |
| ... ELSE |
| ... Should Contain ${route_info} ${gateway_ip} |
| ... msg=Gateway IP address not matching. |
| |
| Verify IP And Netmask On BMC |
| [Documentation] Verify IP and netmask on BMC. |
| [Arguments] ${ip} ${netmask} |
| |
| # Description of the argument(s): |
| # ip IP address to be verified. |
| # netmask netmask value to be verified. |
| |
| ${prefix_length}= Netmask Prefix Length ${netmask} |
| @{ip_data}= Get BMC IP Info |
| |
| ${ip_with_netmask}= Catenate ${ip}/${prefix_length} |
| Should Contain ${ip_data} ${ip_with_netmask} |
| ... msg=IP and netmask pair does not exist. |
| |
| Validate Hostname On BMC |
| [Documentation] Verify that the hostname read via Redfish is the same as the |
| ... hostname configured on system. |
| [Arguments] ${hostname} |
| |
| # Description of argument(s): |
| # hostname A hostname value which is to be compared to the hostname |
| # configured on system. |
| |
| ${sys_hostname}= Get BMC Hostname |
| Should Be Equal ${sys_hostname} ${hostname} |
| ... ignore_case=True msg=Hostname does not exist. |
| |
| Test Teardown Execution |
| [Documentation] Test teardown execution. |
| |
| FFDC On Test Case Fail |
| Redfish.Logout |
| |
| Clear IP Settings On Fail |
| [Documentation] Clear IP settings on fail. |
| [Arguments] ${ip} |
| |
| # Description of argument(s): |
| # ip IP address to be deleted. |
| |
| Run Keyword If '${TEST STATUS}' == 'FAIL' |
| ... Delete IP Address ${ip} |
| |
| Test Teardown Execution |
| |
| Verify CLI and Redfish Nameservers |
| [Documentation] Verify that nameservers obtained via Redfish do not |
| ... match those found in /etc/resolv.conf. |
| |
| ${redfish_nameservers}= Redfish.Get Attribute ${REDFISH_NW_ETH0_URI} StaticNameServers |
| ${resolve_conf_nameservers}= CLI Get Nameservers |
| Rqprint Vars redfish_nameservers resolve_conf_nameservers fmt=terse |
| |
| # Check that the 2 lists are equivalent. |
| ${match}= Evaluate set($redfish_nameservers) == set($resolve_conf_nameservers) |
| Should Be True ${match} |
| ... The nameservers obtained via Redfish do not match those found in /etc/resolv.conf. |
| |
| CLI Get Nameservers |
| [Documentation] Get the nameserver IPs from /etc/resolv.conf and return as a list. |
| |
| # Example of /etc/resolv.conf data: |
| # nameserver x.x.x.x |
| # nameserver y.y.y.y |
| |
| ${stdout} ${stderr} ${rc}= BMC Execute Command egrep nameserver /etc/resolv.conf | cut -f2- -d ' ' |
| ${nameservers}= Split String ${stdout} |
| |
| [Return] ${nameservers} |
| |
| |
| Configure Static Name Servers |
| [Documentation] Configure DNS server on BMC. |
| [Arguments] ${static_name_servers}=${original_redfish_nameservers} |
| |
| # Descripton of the argument(s): |
| # static_name_servers A list of static name server IPs to be |
| # configured on the BMC. |
| |
| Redfish.Patch ${REDFISH_NW_ETH0_URI} body={'StaticNameServers': ${static_name_servers}} |