| DESCRIPTION = "Commented config.txt file for the Raspberry Pi. \ |
| The Raspberry Pi config.txt file is read by the GPU before \ |
| the ARM core is initialised. It can be used to set various \ |
| system configuration parameters." |
| LICENSE = "MIT" |
| LIC_FILES_CHKSUM = "file://${COMMON_LICENSE_DIR}/MIT;md5=0835ade698e0bcf8506ecda2f7b4f302" |
| |
| COMPATIBLE_MACHINE = "^rpi$" |
| |
| SRCREV = "6ac2d832c6c3b208e2669f50ec1abf2c20cb7ff4" |
| SRC_URI = "git://github.com/Evilpaul/RPi-config.git;protocol=https;branch=master \ |
| file://0001-config.txt-reintroduce-start_x.patch \ |
| " |
| |
| S = "${WORKDIR}/git" |
| |
| PR = "r5" |
| |
| INHIBIT_DEFAULT_DEPS = "1" |
| |
| PITFT="${@bb.utils.contains("MACHINE_FEATURES", "pitft", "1", "0", d)}" |
| PITFT22="${@bb.utils.contains("MACHINE_FEATURES", "pitft22", "1", "0", d)}" |
| PITFT28r="${@bb.utils.contains("MACHINE_FEATURES", "pitft28r", "1", "0", d)}" |
| PITFT28c="${@bb.utils.contains("MACHINE_FEATURES", "pitft28c", "1", "0", d)}" |
| PITFT35r="${@bb.utils.contains("MACHINE_FEATURES", "pitft35r", "1", "0", d)}" |
| |
| VC4GRAPHICS="${@bb.utils.contains("MACHINE_FEATURES", "vc4graphics", "1", "0", d)}" |
| VC4DTBO ?= "vc4-kms-v3d" |
| GPIO_IR ?= "18" |
| GPIO_IR_TX ?= "17" |
| |
| CAN_OSCILLATOR ?= "16000000" |
| CAN0_INTERRUPT_PIN ?= "25" |
| CAN1_INTERRUPT_PIN ?= "24" |
| |
| ENABLE_UART ??= "" |
| |
| WM8960="${@bb.utils.contains("MACHINE_FEATURES", "wm8960", "1", "0", d)}" |
| |
| GPIO_SHUTDOWN_PIN ??= "" |
| |
| inherit deploy nopackages |
| |
| do_deploy() { |
| install -d ${DEPLOYDIR}/${BOOTFILES_DIR_NAME} |
| CONFIG=${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt |
| |
| cp ${S}/config.txt $CONFIG |
| |
| if [ -n "${KEY_DECODE_MPG2}" ]; then |
| sed -i '/#decode_MPG2=/ c\decode_MPG2=${KEY_DECODE_MPG2}' $CONFIG |
| fi |
| if [ -n "${KEY_DECODE_WVC1}" ]; then |
| sed -i '/#decode_WVC1=/ c\decode_WVC1=${KEY_DECODE_WVC1}' $CONFIG |
| fi |
| if [ -n "${DISABLE_OVERSCAN}" ]; then |
| sed -i '/#disable_overscan=/ c\disable_overscan=${DISABLE_OVERSCAN}' $CONFIG |
| fi |
| if [ "${DISABLE_SPLASH}" = "1" ]; then |
| sed -i '/#disable_splash=/ c\disable_splash=${DISABLE_SPLASH}' $CONFIG |
| fi |
| |
| # Set overclocking options |
| if [ -n "${ARM_FREQ}" ]; then |
| sed -i '/#arm_freq=/ c\arm_freq=${ARM_FREQ}' $CONFIG |
| fi |
| if [ -n "${GPU_FREQ}" ]; then |
| sed -i '/#gpu_freq=/ c\gpu_freq=${GPU_FREQ}' $CONFIG |
| fi |
| if [ -n "${CORE_FREQ}" ]; then |
| sed -i '/#core_freq=/ c\core_freq=${CORE_FREQ}' $CONFIG |
| fi |
| if [ -n "${SDRAM_FREQ}" ]; then |
| sed -i '/#sdram_freq=/ c\sdram_freq=${SDRAM_FREQ}' $CONFIG |
| fi |
| if [ -n "${OVER_VOLTAGE}" ]; then |
| sed -i '/#over_voltage=/ c\over_voltage=${OVER_VOLTAGE}' $CONFIG |
| fi |
| |
| # GPU memory |
| if [ -n "${GPU_MEM}" ]; then |
| sed -i '/#gpu_mem=/ c\gpu_mem=${GPU_MEM}' $CONFIG |
| fi |
| if [ -n "${GPU_MEM_256}" ]; then |
| sed -i '/#gpu_mem_256=/ c\gpu_mem_256=${GPU_MEM_256}' $CONFIG |
| fi |
| if [ -n "${GPU_MEM_512}" ]; then |
| sed -i '/#gpu_mem_512=/ c\gpu_mem_512=${GPU_MEM_512}' $CONFIG |
| fi |
| if [ -n "${GPU_MEM_1024}" ]; then |
| sed -i '/#gpu_mem_1024=/ c\gpu_mem_1024=${GPU_MEM_1024}' $CONFIG |
| fi |
| |
| # Set boot delay |
| if [ -n "${BOOT_DELAY}" ]; then |
| sed -i '/#boot_delay=/ c\boot_delay=${BOOT_DELAY}' $CONFIG |
| fi |
| if [ -n "${BOOT_DELAY_MS}" ]; then |
| sed -i '/#boot_delay_ms=/ c\boot_delay_ms=${BOOT_DELAY_MS}' $CONFIG |
| fi |
| |
| # Set HDMI and composite video options |
| if [ -n "${HDMI_FORCE_HOTPLUG}" ]; then |
| sed -i '/#hdmi_force_hotplug=/ c\hdmi_force_hotplug=${HDMI_FORCE_HOTPLUG}' $CONFIG |
| fi |
| if [ -n "${HDMI_DRIVE}" ]; then |
| sed -i '/#hdmi_drive=/ c\hdmi_drive=${HDMI_DRIVE}' $CONFIG |
| fi |
| if [ -n "${HDMI_GROUP}" ]; then |
| sed -i '/#hdmi_group=/ c\hdmi_group=${HDMI_GROUP}' $CONFIG |
| fi |
| if [ -n "${HDMI_MODE}" ]; then |
| sed -i '/#hdmi_mode=/ c\hdmi_mode=${HDMI_MODE}' $CONFIG |
| fi |
| if [ -n "${HDMI_CVT}" ]; then |
| echo 'hdmi_cvt=${HDMI_CVT}' >> $CONFIG |
| fi |
| if [ -n "${CONFIG_HDMI_BOOST}" ]; then |
| sed -i '/#config_hdmi_boost=/ c\config_hdmi_boost=${CONFIG_HDMI_BOOST}' $CONFIG |
| fi |
| if [ -n "${SDTV_MODE}" ]; then |
| sed -i '/#sdtv_mode=/ c\sdtv_mode=${SDTV_MODE}' $CONFIG |
| fi |
| if [ -n "${SDTV_ASPECT}" ]; then |
| sed -i '/#sdtv_aspect=/ c\sdtv_aspect=${SDTV_ASPECT}' $CONFIG |
| fi |
| if [ -n "${DISPLAY_ROTATE}" ]; then |
| sed -i '/#display_rotate=/ c\display_rotate=${DISPLAY_ROTATE}' $CONFIG |
| fi |
| |
| # Video camera support |
| if [ "${VIDEO_CAMERA}" = "1" ]; then |
| # It has been observed that Raspberry Pi 4B 4GB may fail to enable the |
| # camera if "start_x=1" is at the end of the file. Therefore, |
| # "start_x=1" has been set to replace the original occurrence in |
| # config.txt, which is at the middle of the file. |
| # The exact underlying cause is unknown. There are similar issues |
| # reported in the raspberrypi/firware repo and the conclusion reached |
| # was that there could be a file size limitation affecting certain |
| # variables. It was commented that this limitation could be 4k but |
| # not proved. |
| sed -i '/#start_x=/ c\start_x=1' $CONFIG |
| fi |
| |
| # Offline compositing support |
| if [ "${DISPMANX_OFFLINE}" = "1" ]; then |
| echo "# Enable offline compositing" >>$CONFIG |
| echo "dispmanx_offline=1" >>$CONFIG |
| fi |
| |
| # SPI bus support |
| if [ "${ENABLE_SPI_BUS}" = "1" ] || [ "${PITFT}" = "1" ]; then |
| echo "# Enable SPI bus" >>$CONFIG |
| echo "dtparam=spi=on" >>$CONFIG |
| fi |
| |
| # I2C support |
| if [ "${ENABLE_I2C}" = "1" ] || [ "${PITFT}" = "1" ]; then |
| echo "# Enable I2C" >>$CONFIG |
| echo "dtparam=i2c1=on" >>$CONFIG |
| echo "dtparam=i2c_arm=on" >>$CONFIG |
| fi |
| |
| # PiTFT22 display support |
| if [ "${PITFT22}" = "1" ]; then |
| echo "# Enable PITFT22 display" >>$CONFIG |
| echo "dtoverlay=pitft22,rotate=270,speed=32000000,txbuflen=32768" >>$CONFIG |
| fi |
| if [ "${PITFT28r}" = "1" ]; then |
| echo "# Enable PITFT28r display" >>$CONFIG |
| echo "dtoverlay=pitft28-resistive,rotate=90,speed=32000000,txbuflen=32768" >>$CONFIG |
| fi |
| if [ "${PITFT28c}" = "1" ]; then |
| echo "# Enable PITFT28c display" >>$CONFIG |
| echo "dtoverlay=pitft28-capacitive,rotate=90,speed=32000000,txbuflen=32768" >>$CONFIG |
| echo "dtoverlay=pitft28-capacitive,touch-swapxy,touch-invx" >>$CONFIG |
| fi |
| if [ "${PITFT35r}" = "1" ]; then |
| echo "# Enable PITFT35r display" >>$CONFIG |
| echo "dtoverlay=pitft35-resistive,rotate=90,speed=42000000,fps=20" >>$CONFIG |
| fi |
| |
| # UART support |
| if [ "${ENABLE_UART}" = "1" ] || [ "${ENABLE_UART}" = "0" ]; then |
| echo "# Enable UART" >>$CONFIG |
| echo "enable_uart=${ENABLE_UART}" >>$CONFIG |
| elif [ -n "${ENABLE_UART}" ]; then |
| bbfatal "Invalid value for ENABLE_UART [${ENABLE_UART}]. The value for ENABLE_UART can be 0 or 1." |
| fi |
| |
| # U-Boot requires "enable_uart=1" for various boards to operate correctly |
| # cf https://source.denx.de/u-boot/u-boot/-/blob/v2023.04/arch/arm/mach-bcm283x/Kconfig?ref_type=tags#L65 |
| if [ "${RPI_USE_U_BOOT}" = "1" ] && [ "${ENABLE_UART}" != "1" ]; then |
| case "${UBOOT_MACHINE}" in |
| rpi_0_w_defconfig|rpi_3_32b_config|rpi_4_32b_config|rpi_arm64_config) |
| if [ "${ENABLE_UART}" = "0" ]; then |
| bbfatal "Invalid configuration: RPI_USE_U_BOOT requires to enable the UART in config.txt for ${MACHINE}" |
| fi |
| echo "# U-Boot requires UART" >>$CONFIG |
| echo "enable_uart=1" >>$CONFIG |
| ;; |
| esac |
| fi |
| |
| # Infrared support |
| if [ "${ENABLE_IR}" = "1" ]; then |
| echo "# Enable infrared" >>$CONFIG |
| echo "dtoverlay=gpio-ir,gpio_pin=${GPIO_IR}" >>$CONFIG |
| echo "dtoverlay=gpio-ir-tx,gpio_pin=${GPIO_IR_TX}" >>$CONFIG |
| fi |
| |
| # VC4 Graphics support |
| if [ "${VC4GRAPHICS}" = "1" ]; then |
| echo "# Enable VC4 Graphics" >> $CONFIG |
| echo "dtoverlay=${VC4DTBO}" >> $CONFIG |
| fi |
| |
| # Choose Camera Sensor to be used, default imx219 sensor |
| if [ "${RASPBERRYPI_CAMERA_V2}" = "1" ]; then |
| echo "# Enable Sony RaspberryPi Camera(imx219)" >> $CONFIG |
| echo "dtoverlay=imx219" >> $CONFIG |
| fi |
| |
| # Choose Camera Sensor to be used, default imx477 sensor |
| #if [ "${RASPBERRYPI_HD_CAMERA}" = "1" ]; then |
| # echo "# Enable Sony RaspberryPi Camera(imx477)" >> $CONFIG |
| # echo "dtoverlay=imx477" >> $CONFIG |
| #fi |
| |
| # Choose Camera Sensor to be used, default imx708 sensor |
| if [ "${RASPBERRYPI_CAMERA_V3}" = "1" ]; then |
| echo "# Enable Sony RaspberryPi Camera(imx708)" >> $CONFIG |
| echo "dtoverlay=imx708" >> $CONFIG |
| fi |
| |
| # Waveshare "C" 1024x600 7" Rev2.1 IPS capacitive touch (http://www.waveshare.com/7inch-HDMI-LCD-C.htm) |
| if [ "${WAVESHARE_1024X600_C_2_1}" = "1" ]; then |
| echo "# Waveshare \"C\" 1024x600 7\" Rev2.1 IPS capacitive touch screen" >> $CONFIG |
| echo "max_usb_current=1" >> $CONFIG |
| echo "hdmi_group=2" >> $CONFIG |
| echo "hdmi_mode=87" >> $CONFIG |
| echo "hdmi_cvt 1024 600 60 6 0 0 0" >> $CONFIG |
| echo "hdmi_drive=1" >> $CONFIG |
| fi |
| |
| # DWC2 USB peripheral support |
| if ([ "${ENABLE_DWC2_PERIPHERAL}" = "1" ] && [ "${ENABLE_DWC2_OTG}" != "1" ]); then |
| echo "# Enable USB peripheral mode" >> $CONFIG |
| echo "dtoverlay=dwc2,dr_mode=peripheral" >> $CONFIG |
| fi |
| |
| # DWC2 USB host mode support |
| if [ "${ENABLE_DWC2_HOST}" = "1" ]; then |
| echo "# Enable USB host mode" >> $CONFIG |
| echo "dtoverlay=dwc2,dr_mode=host" >> $CONFIG |
| fi |
| |
| # DWC2 USB OTG support |
| if ([ "${ENABLE_DWC2_OTG}" = "1" ] && [ "${ENABLE_DWC2_PERIPHERAL}" != "1" ]); then |
| echo "# Enable USB OTG mode" >> $CONFIG |
| echo "dtoverlay=dwc2,dr_mode=otg" >> $CONFIG |
| fi |
| |
| # AT86RF23X support |
| if [ "${ENABLE_AT86RF}" = "1" ]; then |
| echo "# Enable AT86RF23X" >>$CONFIG |
| echo "dtoverlay=at86rf233,speed=3000000" >>$CONFIG |
| fi |
| |
| # ENABLE DUAL CAN |
| if [ "${ENABLE_DUAL_CAN}" = "1" ]; then |
| echo "# Enable DUAL CAN" >>$CONFIG |
| echo "dtoverlay=mcp2515-can0,oscillator=${CAN_OSCILLATOR},interrupt=${CAN0_INTERRUPT_PIN}" >>$CONFIG |
| echo "dtoverlay=mcp2515-can1,oscillator=${CAN_OSCILLATOR},interrupt=${CAN1_INTERRUPT_PIN}" >>$CONFIG |
| # ENABLE CAN |
| elif [ "${ENABLE_CAN}" = "1" ]; then |
| echo "# Enable CAN" >>$CONFIG |
| echo "dtoverlay=mcp2515-can0,oscillator=${CAN_OSCILLATOR},interrupt=${CAN0_INTERRUPT_PIN}" >>$CONFIG |
| fi |
| |
| |
| if [ "${ENABLE_GPIO_SHUTDOWN}" = "1" ]; then |
| if ([ "${ENABLE_I2C}" = "1" ] || [ "${PITFT}" = "1" ]) && [ -z "${GPIO_SHUTDOWN_PIN}" ]; then |
| # By default GPIO shutdown uses the same pin as the (master) I2C SCL. |
| # If I2C is configured and an alternative pin is not configured for |
| # gpio-shutdown, there is a configuration conflict. |
| bbfatal "I2C and gpio-shutdown are both enabled and using the same pins!" |
| fi |
| echo "# Enable gpio-shutdown" >> $CONFIG |
| if [ -z "${GPIO_SHUTDOWN_PIN}" ]; then |
| echo "dtoverlay=gpio-shutdown" >> $CONFIG |
| else |
| echo "dtoverlay=gpio-shutdown,gpio_pin=${GPIO_SHUTDOWN_PIN}" >> $CONFIG |
| fi |
| fi |
| |
| # Append extra config if the user has provided any |
| printf "${RPI_EXTRA_CONFIG}\n" >> $CONFIG |
| |
| # Handle setup with armstub file |
| if [ "${@bb.utils.contains("MACHINE_FEATURES", "armstub", "1", "0", d)}" = "1" ]; then |
| echo "\n# ARM stub configuration" >> $CONFIG |
| echo "armstub=${ARMSTUB}" >> $CONFIG |
| case "${ARMSTUB}" in |
| *-gic.bin) |
| echo "enable_gic=1" >> $CONFIG |
| ;; |
| esac |
| fi |
| |
| # WM8960 support |
| if [ "${WM8960}" = "1" ]; then |
| echo "# Enable WM8960" >> $CONFIG |
| echo "dtoverlay=wm8960-soundcard" >> $CONFIG |
| fi |
| |
| # W1-GPIO - One-Wire Interface |
| if [ "${ENABLE_W1}" = "1" ]; then |
| echo "# Enable One-Wire Interface" >> $CONFIG |
| echo "dtoverlay=w1-gpio" >> $CONFIG |
| fi |
| |
| # Reduce config.txt file size to avoid corruption and |
| # to boot successfully Raspberry Pi 5. The issue has |
| # been reported to related projects: |
| # https://github.com/raspberrypi/firmware/issues/1848 |
| # https://github.com/Evilpaul/RPi-config/issues/9 |
| sed -i '/^##/d' $CONFIG |
| } |
| |
| do_deploy:append:raspberrypi3-64() { |
| echo "# have a properly sized image" >> $CONFIG |
| echo "disable_overscan=1" >> $CONFIG |
| |
| echo "# Enable audio (loads snd_bcm2835)" >> $CONFIG |
| echo "dtparam=audio=on" >> $CONFIG |
| } |
| |
| do_deploy:append() { |
| if grep -q -E '^.{80}.$' ${DEPLOYDIR}/${BOOTFILES_DIR_NAME}/config.txt; then |
| bbwarn "config.txt contains lines longer than 80 characters, this is not supported" |
| fi |
| } |
| |
| addtask deploy before do_build after do_install |
| do_deploy[dirs] += "${DEPLOYDIR}/${BOOTFILES_DIR_NAME}" |
| |
| PACKAGE_ARCH = "${MACHINE_ARCH}" |