blob: b3338ca85956225ce465d548826146cfd0651d6c [file] [log] [blame]
# Copyright (C) 2014 Intel Corporation
#
# Released under the MIT license (see COPYING.MIT)
# This module adds support to testimage.bbclass to deploy images and run
# tests on a Ubiquiti Networks EdgeRouter Lite. The device must be set up
# to boot into the master image already - the easiest way to do that is as
# follows:
#
# 1. Take out the internal USB drive and plug it into your PC
# 2. Repartition the USB drive so that you have three partitions in this
# order:
# 1: vfat, labelled "boot" (it will need to be formatted with mkfs.vfat
# for this to be possible, since FAT partitions formatted under
# DOS/Windows will only support uppercase labels)
# 2: ext3 (for master image) labelled "testmaster"
# 3: ext3 (for image under test) labelled "testrootfs"
# 3. Copy the kernel to be used by the master image to the FAT partition
# (it should be named "vmlinux.64" with the factory u-boot configuration)
# 4. Install the master image onto the "testmaster" ext3 partition. If
# you do this by just extracting the contents of an image onto the
# partition, you will also likely need to create the master image marker
# file /etc/masterimage within this partition so that we can tell when
# we're booted into it that it is the master image.
# 5. Put the USB drive back into the device, and ensure the console port
# and first ethernet port are connected before powering on
#
# TEST_SERIALCONTROL_CMD will need to be set in local.conf so that we can
# interact with u-boot over the serial console port.
import os
import bb
import time
import subprocess
import sys
import pexpect
import oeqa.utils.sshcontrol as sshcontrol
from oeqa.controllers.masterimage import MasterImageHardwareTarget
class EdgeRouterTarget(MasterImageHardwareTarget):
def __init__(self, d):
super(EdgeRouterTarget, self).__init__(d)
self.image_fstype = self.get_image_fstype(d)
self.deploy_cmds = [
'mount -L boot /boot',
'mkdir -p /mnt/testrootfs',
'mount -L testrootfs /mnt/testrootfs',
'cp ~/test-kernel /boot',
'rm -rf /mnt/testrootfs/*',
'tar xvf ~/test-rootfs.%s -C /mnt/testrootfs' % self.image_fstype
]
if not self.serialcontrol_cmd:
bb.fatal("This TEST_TARGET needs a TEST_SERIALCONTROL_CMD defined in local.conf.")
def _deploy(self):
self.master.run("umount /mnt/testrootfs;")
self.master.ignore_status = False
self.master.copy_to(self.kernel, "~/test-kernel")
self.master.copy_to(self.rootfs, "~/test-rootfs.%s" % self.image_fstype)
for cmd in self.deploy_cmds:
self.master.run(cmd)
def _start(self, params=None):
self.power_cycle(self.master)
try:
serialconn = pexpect.spawn(self.serialcontrol_cmd, env=self.origenv, logfile=sys.stdout)
serialconn.expect("U-Boot")
serialconn.sendline("a")
serialconn.expect("Octeon ubnt_e100#")
serialconn.sendline("fatload usb 0:1 $loadaddr test-kernel")
serialconn.expect(" bytes read")
serialconn.expect("Octeon ubnt_e100#")
serialconn.sendline("bootoctlinux $loadaddr coremask=0x3 root=/dev/sda3 rw rootwait mtdparts=phys_mapped_flash:512k(boot0),512k(boot1),64k@3072k(eeprom)")
serialconn.expect("login:", timeout=120)
serialconn.close()
except pexpect.ExceptionPexpect as e:
bb.fatal('Serial interaction failed: %s' % str(e))
def _wait_until_booted(self):
try:
serialconn = pexpect.spawn(self.serialcontrol_cmd, env=self.origenv, logfile=sys.stdout)
serialconn.expect("login:", timeout=120)
serialconn.close()
except pexpect.ExceptionPexpect as e:
bb.fatal('Serial interaction failed: %s' % str(e))