import-layers/meta-raspberrypi/classes/sdcard_image-rpi.bbclass - openbmc/openbmc - Gitiles

 inherit image_types
 inherit linux-raspberrypi-base

 #
 # Create an image that can by written onto a SD card using dd.
 #
 # The disk layout used is:
 #
 #    0                      -> IMAGE_ROOTFS_ALIGNMENT         - reserved for other data
 #    IMAGE_ROOTFS_ALIGNMENT -> BOOT_SPACE                     - bootloader and kernel
 #    BOOT_SPACE             -> SDIMG_SIZE                     - rootfs
 #

 #                                                     Default Free space = 1.3x
 #                                                     Use IMAGE_OVERHEAD_FACTOR to add more space
 #                                                     <--------->
 #            4MiB              40MiB           SDIMG_ROOTFS
 # <-----------------------> <----------> <---------------------->
 #  ------------------------ ------------ ------------------------
 # | IMAGE_ROOTFS_ALIGNMENT | BOOT_SPACE | ROOTFS_SIZE            |
 #  ------------------------ ------------ ------------------------
 # ^                        ^            ^                        ^
 # |                        |            |                        |
 # 0                      4MiB     4MiB + 40MiB       4MiB + 40Mib + SDIMG_ROOTFS

 # This image depends on the rootfs image
 IMAGE_TYPEDEP_rpi-sdimg = "${SDIMG_ROOTFS_TYPE}"

 # Set kernel and boot loader
 IMAGE_BOOTLOADER ?= "bcm2835-bootfiles"

 # Set initramfs extension
 KERNEL_INITRAMFS ?= ""

 # Kernel image name
 SDIMG_KERNELIMAGE_raspberrypi  ?= "kernel.img"
 SDIMG_KERNELIMAGE_raspberrypi2 ?= "kernel7.img"

 # Boot partition volume id
 BOOTDD_VOLUME_ID ?= "${MACHINE}"

 # Boot partition size [in KiB] (will be rounded up to IMAGE_ROOTFS_ALIGNMENT)
 BOOT_SPACE ?= "40960"

 # Set alignment to 4MB [in KiB]
 IMAGE_ROOTFS_ALIGNMENT = "4096"

 # Use an uncompressed ext3 by default as rootfs
 SDIMG_ROOTFS_TYPE ?= "ext3"
 SDIMG_ROOTFS = "${DEPLOY_DIR_IMAGE}/${IMAGE_NAME}.rootfs.${SDIMG_ROOTFS_TYPE}"

 IMAGE_DEPENDS_rpi-sdimg = " \
 			parted-native \
 			mtools-native \
 			dosfstools-native \
 			virtual/kernel:do_deploy \
 			${IMAGE_BOOTLOADER} \
 			${@bb.utils.contains('KERNEL_IMAGETYPE', 'uImage', 'u-boot', '',d)} \
 			"

 # SD card image name
 SDIMG = "${DEPLOY_DIR_IMAGE}/${IMAGE_NAME}.rootfs.rpi-sdimg"

 # Compression method to apply to SDIMG after it has been created. Supported
 # compression formats are "gzip", "bzip2" or "xz". The original .rpi-sdimg file
 # is kept and a new compressed file is created if one of these compression
 # formats is chosen. If SDIMG_COMPRESSION is set to any other value it is
 # silently ignored.
 #SDIMG_COMPRESSION ?= ""

 # Additional files and/or directories to be copied into the vfat partition from the IMAGE_ROOTFS.
 FATPAYLOAD ?= ""

 IMAGEDATESTAMP = "${@time.strftime('%Y.%m.%d',time.gmtime())}"
 IMAGE_CMD_rpi-sdimg[vardepsexclude] += "IMAGEDATESTAMP"
 IMAGE_CMD_rpi-sdimg[vardepsexclude] += "DATETIME"

 IMAGE_CMD_rpi-sdimg () {

 	# Align partitions
 	BOOT_SPACE_ALIGNED=$(expr ${BOOT_SPACE} + ${IMAGE_ROOTFS_ALIGNMENT} - 1)
 	BOOT_SPACE_ALIGNED=$(expr ${BOOT_SPACE_ALIGNED} - ${BOOT_SPACE_ALIGNED} % ${IMAGE_ROOTFS_ALIGNMENT})
 	SDIMG_SIZE=$(expr ${IMAGE_ROOTFS_ALIGNMENT} + ${BOOT_SPACE_ALIGNED} + $ROOTFS_SIZE)

 	echo "Creating filesystem with Boot partition ${BOOT_SPACE_ALIGNED} KiB and RootFS $ROOTFS_SIZE KiB"

 	# Check if we are building with device tree support
 	DTS="${@get_dts(d, None)}"

 	# Initialize sdcard image file
 	dd if=/dev/zero of=${SDIMG} bs=1024 count=0 seek=${SDIMG_SIZE}

 	# Create partition table
 	parted -s ${SDIMG} mklabel msdos
 	# Create boot partition and mark it as bootable
 	parted -s ${SDIMG} unit KiB mkpart primary fat32 ${IMAGE_ROOTFS_ALIGNMENT} $(expr ${BOOT_SPACE_ALIGNED} \+ ${IMAGE_ROOTFS_ALIGNMENT})
 	parted -s ${SDIMG} set 1 boot on
 	# Create rootfs partition to the end of disk
 	parted -s ${SDIMG} -- unit KiB mkpart primary ext2 $(expr ${BOOT_SPACE_ALIGNED} \+ ${IMAGE_ROOTFS_ALIGNMENT}) -1s
 	parted ${SDIMG} print

 	# Create a vfat image with boot files
 	BOOT_BLOCKS=$(LC_ALL=C parted -s ${SDIMG} unit b print | awk '/ 1 / { print substr($4, 1, length($4 -1)) / 512 /2 }')
 	rm -f ${WORKDIR}/boot.img
 	mkfs.vfat -n "${BOOTDD_VOLUME_ID}" -S 512 -C ${WORKDIR}/boot.img $BOOT_BLOCKS
 	mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/bcm2835-bootfiles/* ::/
 	if test -n "${DTS}"; then
 		# Device Tree Overlays are assumed to be suffixed by '-overlay.dtb' string and will be put in a dedicated folder
 		DT_OVERLAYS="${@split_overlays(d, 0)}"
 		DT_ROOT="${@split_overlays(d, 1)}"

 		# Copy board device trees to root folder
 		for DTB in ${DT_ROOT}; do
 			DTB_BASE_NAME=`basename ${DTB} .dtb`

 			mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${DTB_BASE_NAME}.dtb ::${DTB_BASE_NAME}.dtb
 		done

 		# Copy device tree overlays to dedicated folder
 		mmd -i ${WORKDIR}/boot.img overlays
 		for DTB in ${DT_OVERLAYS}; do
 			DTB_BASE_NAME=`basename ${DTB} .dtb`

 			mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${DTB_BASE_NAME}.dtb ::overlays/${DTB_BASE_NAME}.dtb
 		done
 	fi
 	case "${KERNEL_IMAGETYPE}" in
 	"uImage")
 		mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/u-boot.bin ::${SDIMG_KERNELIMAGE}
 		mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}${KERNEL_INITRAMFS}-${MACHINE}.bin ::uImage
 		;;
 	*)
 		mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}${KERNEL_INITRAMFS}-${MACHINE}.bin ::${SDIMG_KERNELIMAGE}
 		;;
 	esac

 	if [ -n ${FATPAYLOAD} ] ; then
 		echo "Copying payload into VFAT"
 		for entry in ${FATPAYLOAD} ; do
 				# add the || true to stop aborting on vfat issues like not supporting .~lock files
 				mcopy -i ${WORKDIR}/boot.img -s -v ${IMAGE_ROOTFS}$entry :: || true
 		done
 	fi

 	# Add stamp file
 	echo "${IMAGE_NAME}-${IMAGEDATESTAMP}" > ${WORKDIR}/image-version-info
 	mcopy -i ${WORKDIR}/boot.img -v ${WORKDIR}//image-version-info ::

 	# Burn Partitions
 	dd if=${WORKDIR}/boot.img of=${SDIMG} conv=notrunc seek=1 bs=$(expr ${IMAGE_ROOTFS_ALIGNMENT} \* 1024) && sync && sync
 	# If SDIMG_ROOTFS_TYPE is a .xz file use xzcat
 	if echo "${SDIMG_ROOTFS_TYPE}" | egrep -q "*\.xz"
 	then
 		xzcat ${SDIMG_ROOTFS} | dd of=${SDIMG} conv=notrunc seek=1 bs=$(expr 1024 \* ${BOOT_SPACE_ALIGNED} + ${IMAGE_ROOTFS_ALIGNMENT} \* 1024) && sync && sync
 	else
 		dd if=${SDIMG_ROOTFS} of=${SDIMG} conv=notrunc seek=1 bs=$(expr 1024 \* ${BOOT_SPACE_ALIGNED} + ${IMAGE_ROOTFS_ALIGNMENT} \* 1024) && sync && sync
 	fi

 	# Optionally apply compression
 	case "${SDIMG_COMPRESSION}" in
 	"gzip")
 		gzip -k9 "${SDIMG}"
 		;;
 	"bzip2")
 		bzip2 -k9 "${SDIMG}"
 		;;
 	"xz")
 		xz -k "${SDIMG}"
 		;;
 	esac
 }

 ROOTFS_POSTPROCESS_COMMAND += " rpi_generate_sysctl_config ; "

 rpi_generate_sysctl_config() {
 	# systemd sysctl config
 	test -d ${IMAGE_ROOTFS}${sysconfdir}/sysctl.d && \
 		echo "vm.min_free_kbytes = 8192" > ${IMAGE_ROOTFS}${sysconfdir}/sysctl.d/rpi-vm.conf

 	# sysv sysctl config
 	IMAGE_SYSCTL_CONF="${IMAGE_ROOTFS}${sysconfdir}/sysctl.conf"
 	test -e ${IMAGE_ROOTFS}${sysconfdir}/sysctl.conf && \
 		sed -e "/vm.min_free_kbytes/d" -i ${IMAGE_SYSCTL_CONF}
 	echo "" >> ${IMAGE_SYSCTL_CONF} && echo "vm.min_free_kbytes = 8192" >> ${IMAGE_SYSCTL_CONF}
 }
	inherit image_types
	inherit linux-raspberrypi-base

	#
	# Create an image that can by written onto a SD card using dd.
	#
	# The disk layout used is:
	#
	# 0 -> IMAGE_ROOTFS_ALIGNMENT - reserved for other data
	# IMAGE_ROOTFS_ALIGNMENT -> BOOT_SPACE - bootloader and kernel
	# BOOT_SPACE -> SDIMG_SIZE - rootfs
	#

	# Default Free space = 1.3x
	# Use IMAGE_OVERHEAD_FACTOR to add more space
	# <--------->
	# 4MiB 40MiB SDIMG_ROOTFS
	# <-----------------------> <----------> <---------------------->
	# ------------------------ ------------ ------------------------
	# \| IMAGE_ROOTFS_ALIGNMENT \| BOOT_SPACE \| ROOTFS_SIZE \|
	# ------------------------ ------------ ------------------------
	# ^ ^ ^ ^
	# \| \| \| \|
	# 0 4MiB 4MiB + 40MiB 4MiB + 40Mib + SDIMG_ROOTFS

	# This image depends on the rootfs image
	IMAGE_TYPEDEP_rpi-sdimg = "${SDIMG_ROOTFS_TYPE}"

	# Set kernel and boot loader
	IMAGE_BOOTLOADER ?= "bcm2835-bootfiles"

	# Set initramfs extension
	KERNEL_INITRAMFS ?= ""

	# Kernel image name
	SDIMG_KERNELIMAGE_raspberrypi ?= "kernel.img"
	SDIMG_KERNELIMAGE_raspberrypi2 ?= "kernel7.img"

	# Boot partition volume id
	BOOTDD_VOLUME_ID ?= "${MACHINE}"

	# Boot partition size [in KiB] (will be rounded up to IMAGE_ROOTFS_ALIGNMENT)
	BOOT_SPACE ?= "40960"

	# Set alignment to 4MB [in KiB]
	IMAGE_ROOTFS_ALIGNMENT = "4096"

	# Use an uncompressed ext3 by default as rootfs
	SDIMG_ROOTFS_TYPE ?= "ext3"
	SDIMG_ROOTFS = "${DEPLOY_DIR_IMAGE}/${IMAGE_NAME}.rootfs.${SDIMG_ROOTFS_TYPE}"

	IMAGE_DEPENDS_rpi-sdimg = " \
	parted-native \
	mtools-native \
	dosfstools-native \
	virtual/kernel:do_deploy \
	${IMAGE_BOOTLOADER} \
	${@bb.utils.contains('KERNEL_IMAGETYPE', 'uImage', 'u-boot', '',d)} \
	"

	# SD card image name
	SDIMG = "${DEPLOY_DIR_IMAGE}/${IMAGE_NAME}.rootfs.rpi-sdimg"

	# Compression method to apply to SDIMG after it has been created. Supported
	# compression formats are "gzip", "bzip2" or "xz". The original .rpi-sdimg file
	# is kept and a new compressed file is created if one of these compression
	# formats is chosen. If SDIMG_COMPRESSION is set to any other value it is
	# silently ignored.
	#SDIMG_COMPRESSION ?= ""

	# Additional files and/or directories to be copied into the vfat partition from the IMAGE_ROOTFS.
	FATPAYLOAD ?= ""

	IMAGEDATESTAMP = "${@time.strftime('%Y.%m.%d',time.gmtime())}"
	IMAGE_CMD_rpi-sdimg[vardepsexclude] += "IMAGEDATESTAMP"
	IMAGE_CMD_rpi-sdimg[vardepsexclude] += "DATETIME"

	IMAGE_CMD_rpi-sdimg () {

	# Align partitions
	BOOT_SPACE_ALIGNED=$(expr ${BOOT_SPACE} + ${IMAGE_ROOTFS_ALIGNMENT} - 1)
	BOOT_SPACE_ALIGNED=$(expr ${BOOT_SPACE_ALIGNED} - ${BOOT_SPACE_ALIGNED} % ${IMAGE_ROOTFS_ALIGNMENT})
	SDIMG_SIZE=$(expr ${IMAGE_ROOTFS_ALIGNMENT} + ${BOOT_SPACE_ALIGNED} + $ROOTFS_SIZE)

	echo "Creating filesystem with Boot partition ${BOOT_SPACE_ALIGNED} KiB and RootFS $ROOTFS_SIZE KiB"

	# Check if we are building with device tree support
	DTS="${@get_dts(d, None)}"

	# Initialize sdcard image file
	dd if=/dev/zero of=${SDIMG} bs=1024 count=0 seek=${SDIMG_SIZE}

	# Create partition table
	parted -s ${SDIMG} mklabel msdos
	# Create boot partition and mark it as bootable
	parted -s ${SDIMG} unit KiB mkpart primary fat32 ${IMAGE_ROOTFS_ALIGNMENT} $(expr ${BOOT_SPACE_ALIGNED} \+ ${IMAGE_ROOTFS_ALIGNMENT})
	parted -s ${SDIMG} set 1 boot on
	# Create rootfs partition to the end of disk
	parted -s ${SDIMG} -- unit KiB mkpart primary ext2 $(expr ${BOOT_SPACE_ALIGNED} \+ ${IMAGE_ROOTFS_ALIGNMENT}) -1s
	parted ${SDIMG} print

	# Create a vfat image with boot files
	BOOT_BLOCKS=$(LC_ALL=C parted -s ${SDIMG} unit b print \| awk '/ 1 / { print substr($4, 1, length($4 -1)) / 512 /2 }')
	rm -f ${WORKDIR}/boot.img
	mkfs.vfat -n "${BOOTDD_VOLUME_ID}" -S 512 -C ${WORKDIR}/boot.img $BOOT_BLOCKS
	mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/bcm2835-bootfiles/* ::/
	if test -n "${DTS}"; then
	# Device Tree Overlays are assumed to be suffixed by '-overlay.dtb' string and will be put in a dedicated folder
	DT_OVERLAYS="${@split_overlays(d, 0)}"
	DT_ROOT="${@split_overlays(d, 1)}"

	# Copy board device trees to root folder
	for DTB in ${DT_ROOT}; do
	DTB_BASE_NAME=`basename ${DTB} .dtb`

	mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${DTB_BASE_NAME}.dtb ::${DTB_BASE_NAME}.dtb
	done

	# Copy device tree overlays to dedicated folder
	mmd -i ${WORKDIR}/boot.img overlays
	for DTB in ${DT_OVERLAYS}; do
	DTB_BASE_NAME=`basename ${DTB} .dtb`

	mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}-${DTB_BASE_NAME}.dtb ::overlays/${DTB_BASE_NAME}.dtb
	done
	fi
	case "${KERNEL_IMAGETYPE}" in
	"uImage")
	mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/u-boot.bin ::${SDIMG_KERNELIMAGE}
	mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}${KERNEL_INITRAMFS}-${MACHINE}.bin ::uImage
	;;
	*)
	mcopy -i ${WORKDIR}/boot.img -s ${DEPLOY_DIR_IMAGE}/${KERNEL_IMAGETYPE}${KERNEL_INITRAMFS}-${MACHINE}.bin ::${SDIMG_KERNELIMAGE}
	;;
	esac

	if [ -n ${FATPAYLOAD} ] ; then
	echo "Copying payload into VFAT"
	for entry in ${FATPAYLOAD} ; do
	# add the \|\| true to stop aborting on vfat issues like not supporting .~lock files
	mcopy -i ${WORKDIR}/boot.img -s -v ${IMAGE_ROOTFS}$entry :: \|\| true
	done
	fi

	# Add stamp file
	echo "${IMAGE_NAME}-${IMAGEDATESTAMP}" > ${WORKDIR}/image-version-info
	mcopy -i ${WORKDIR}/boot.img -v ${WORKDIR}//image-version-info ::

	# Burn Partitions
	dd if=${WORKDIR}/boot.img of=${SDIMG} conv=notrunc seek=1 bs=$(expr ${IMAGE_ROOTFS_ALIGNMENT} \* 1024) && sync && sync
	# If SDIMG_ROOTFS_TYPE is a .xz file use xzcat
	if echo "${SDIMG_ROOTFS_TYPE}" \| egrep -q "*\.xz"
	then
	xzcat ${SDIMG_ROOTFS} \| dd of=${SDIMG} conv=notrunc seek=1 bs=$(expr 1024 \* ${BOOT_SPACE_ALIGNED} + ${IMAGE_ROOTFS_ALIGNMENT} \* 1024) && sync && sync
	else
	dd if=${SDIMG_ROOTFS} of=${SDIMG} conv=notrunc seek=1 bs=$(expr 1024 \* ${BOOT_SPACE_ALIGNED} + ${IMAGE_ROOTFS_ALIGNMENT} \* 1024) && sync && sync
	fi

	# Optionally apply compression
	case "${SDIMG_COMPRESSION}" in
	"gzip")
	gzip -k9 "${SDIMG}"
	;;
	"bzip2")
	bzip2 -k9 "${SDIMG}"
	;;
	"xz")
	xz -k "${SDIMG}"
	;;
	esac
	}

	ROOTFS_POSTPROCESS_COMMAND += " rpi_generate_sysctl_config ; "

	rpi_generate_sysctl_config() {
	# systemd sysctl config
	test -d ${IMAGE_ROOTFS}${sysconfdir}/sysctl.d && \
	echo "vm.min_free_kbytes = 8192" > ${IMAGE_ROOTFS}${sysconfdir}/sysctl.d/rpi-vm.conf

	# sysv sysctl config
	IMAGE_SYSCTL_CONF="${IMAGE_ROOTFS}${sysconfdir}/sysctl.conf"
	test -e ${IMAGE_ROOTFS}${sysconfdir}/sysctl.conf && \
	sed -e "/vm.min_free_kbytes/d" -i ${IMAGE_SYSCTL_CONF}
	echo "" >> ${IMAGE_SYSCTL_CONF} && echo "vm.min_free_kbytes = 8192" >> ${IMAGE_SYSCTL_CONF}
	}