meta-ampere/meta-mitchell/recipes-ampere/platform/ampere-utils/ampere_flash_bios.sh

#!/bin/bash

# This script is used to flash the UEFI/EDKII

# Syntax: ampere_flash_bios.sh $image_file $device_sellect
# Where:
#       $image_file : the image binary file
#       $device_sellect : 1 - Host Main SPI Nor
#                         2 - Host Second SPI Nor

# Author : Chanh Nguyen (chnguyen@amperecomputing.com)

# Note:
#      BMC_GPIOW6_SPI0_PROGRAM_SEL (GPIO 182): 1 => BMC owns SPI bus for upgrading
#                                              0 => HOST owns SPI bus for upgrading

#      BMC_GPIOW7_SPI0_BACKUP_SEL (GPIO 183) :  1 => to switch SPI_CS0_L to primary SPI Nor device
#                                               0 => to switch SPI_CS0_L to second SPI Nor device

# shellcheck disable=SC2046

do_flash () {
	# Check the HNOR partition available
	HOST_MTD=$(< /proc/mtd grep "pnor" | sed -n 's/^\(.*\):.*/\1/p')
	if [ -z "$HOST_MTD" ];
	then
		# Check the ASpeed SMC driver binded before
		HOST_SPI=/sys/bus/platform/drivers/spi-aspeed-smc/1e630000.spi
		if [ -d "$HOST_SPI" ]; then
			echo "Unbind the ASpeed SMC driver"
			echo 1e630000.spi > /sys/bus/platform/drivers/spi-aspeed-smc/unbind
			sleep 2
		fi

		# If the HNOR partition is not available, then bind again driver
		echo "--- Bind the ASpeed SMC driver"
		echo 1e630000.spi > /sys/bus/platform/drivers/spi-aspeed-smc/bind
		sleep 2

		HOST_MTD=$(< /proc/mtd grep "pnor" | sed -n 's/^\(.*\):.*/\1/p')
		if [ -z "$HOST_MTD" ];
		then
			echo "Fail to probe Host SPI-NOR device"
			exit 1
		fi
	fi

	echo "--- Flashing firmware image $IMAGE to @/dev/$HOST_MTD"
	flashcp -v "$IMAGE" /dev/"$HOST_MTD"
}


if [ $# -eq 0 ]; then
	echo "Usage: $(basename "$0") <UEFI/EDKII image file> <DEV_SEL> [SPECIAL_BOOT]"
	echo "Where:"
	echo "    DEV_SEL 1 is Primary SPI (by default), 2 is Second SPI"
	echo "    SPECIAL_BOOT: Optional, input '1' to enter & flash SPECIAL_BOOT mode. Default: 0"
	exit 0
fi

IMAGE="$1"
if [ ! -f "$IMAGE" ]; then
	echo "The image file $IMAGE does not exist"
	exit 1
fi

if [ -z "$2" ]; then
       DEV_SEL="1"    # by default, select primary device
else
       DEV_SEL="$2"
fi

SPECIAL_BOOT=0
if [[ "$3" == "1" ]]; then
	SPECIAL_BOOT=1
fi

echo "SPECIAL_BOOT mode: $SPECIAL_BOOT"
# Turn off the Host if it is currently ON
chassisstate=$(obmcutil chassisstate | awk -F. '{print $NF}')
echo "--- Current Chassis State: $chassisstate"
if [ "$chassisstate" == 'On' ];
then
	echo "--- Turning the Chassis off"
	obmcutil chassisoff
	sleep 10
	# Check if HOST was OFF
	chassisstate_off=$(obmcutil chassisstate | awk -F. '{print $NF}')
	if [ "$chassisstate_off" == 'On' ];
	then
		echo "--- Error : Failed turning the Chassis off"
		exit 1
	fi
fi

# Switch the host SPI bus to BMC"
echo "--- Switch the host SPI bus to BMC."
if ! gpioset $(gpiofind spi0-program-sel)=1; then
	echo "ERROR: Switch the host SPI bus to BMC. Please check gpio state"
	exit 1
fi

# Switch the host SPI bus (between primary and secondary)
# 183 is BMC_GPIOW7_SPI0_BACKUP_SEL
if [[ $DEV_SEL == 1 ]]; then
	echo "Run update Primary Host SPI-NOR"
	gpioset $(gpiofind spi0-backup-sel)=1       # Primary SPI
elif [[ $DEV_SEL == 2 ]]; then
	echo "Run update Second Host SPI-NOR"
	gpioset $(gpiofind spi0-backup-sel)=0       # Second SPI
else
	echo "Please choose primary SPI (1) or second SPI (2)"
	exit 0
fi

# Restrict to flash Second Host SPI-NOR in case of SPECIAL_BOOT
if [ $SPECIAL_BOOT == 1 ] && [ "$DEV_SEL" == 2 ]; then
	echo "Not allow to flash the Second Host SPI-NOR with SPECIAL_BOOT image"
	exit
fi

# Flash the firmware
do_flash

# Assert SPECIAL_BOOT GPIO PIN
if [[ $SPECIAL_BOOT == 1 ]]; then
	gpioset $(gpiofind host0-special-boot)=1
fi

# Switch the SPI bus to the primary spi device
echo "Switch to the Primary Host SPI-NOR"
gpioset $(gpiofind spi0-backup-sel)=1       # Primary SPI

# Switch the host SPI bus to HOST."
echo "--- Switch the host SPI bus to HOST."
if ! gpioset $(gpiofind spi0-program-sel)=0; then
	echo "ERROR: Switch the host SPI bus to HOST. Please check gpio state"
	exit 1
fi

if [ "$chassisstate" == 'On' ] || [ $SPECIAL_BOOT == 1 ];
then
	sleep 5
	echo "Turn on the Host"
	obmcutil poweron
fi

# Deassert SPECIAL_BOOT GPIO PIN if it is being asserted
if [[ $SPECIAL_BOOT == 1 ]]; then
	# Time out checking for Host ON is 60s
	cnt=12
	while [ "$cnt" -gt 0 ];
	do
		cnt=$((cnt - 1))
		if systemctl status obmc-host-already-on@0.target | grep "Active: active"; then
			echo "Deassert SPECIAL_BOOT GPIO PIN if it is being asserted."
			gpioset $(gpiofind host0-special-boot)=0
			exit 0
		fi
		sleep 5
	done
fi