xml/p10/node_eq_qme_fir_p10_10.xml

<?xml version="1.0" encoding="UTF-8"?>
<attn_node model_ec="P10_10" name="EQ_QME_FIR" reg_type="SCOM">
    <register name="EQ_QME_FIR">
        <instance addr="0x200E0000" reg_inst="0"/>
        <instance addr="0x210E0000" reg_inst="1"/>
        <instance addr="0x220E0000" reg_inst="2"/>
        <instance addr="0x230E0000" reg_inst="3"/>
        <instance addr="0x240E0000" reg_inst="4"/>
        <instance addr="0x250E0000" reg_inst="5"/>
        <instance addr="0x260E0000" reg_inst="6"/>
        <instance addr="0x270E0000" reg_inst="7"/>
    </register>
    <register name="EQ_QME_FIR_MASK">
        <instance addr="0x200E0004" reg_inst="0"/>
        <instance addr="0x210E0004" reg_inst="1"/>
        <instance addr="0x220E0004" reg_inst="2"/>
        <instance addr="0x230E0004" reg_inst="3"/>
        <instance addr="0x240E0004" reg_inst="4"/>
        <instance addr="0x250E0004" reg_inst="5"/>
        <instance addr="0x260E0004" reg_inst="6"/>
        <instance addr="0x270E0004" reg_inst="7"/>
    </register>
    <register name="EQ_QME_FIR_ACT0">
        <instance addr="0x200E0008" reg_inst="0"/>
        <instance addr="0x210E0008" reg_inst="1"/>
        <instance addr="0x220E0008" reg_inst="2"/>
        <instance addr="0x230E0008" reg_inst="3"/>
        <instance addr="0x240E0008" reg_inst="4"/>
        <instance addr="0x250E0008" reg_inst="5"/>
        <instance addr="0x260E0008" reg_inst="6"/>
        <instance addr="0x270E0008" reg_inst="7"/>
    </register>
    <register name="EQ_QME_FIR_ACT1">
        <instance addr="0x200E000c" reg_inst="0"/>
        <instance addr="0x210E000c" reg_inst="1"/>
        <instance addr="0x220E000c" reg_inst="2"/>
        <instance addr="0x230E000c" reg_inst="3"/>
        <instance addr="0x240E000c" reg_inst="4"/>
        <instance addr="0x250E000c" reg_inst="5"/>
        <instance addr="0x260E000c" reg_inst="6"/>
        <instance addr="0x270E000c" reg_inst="7"/>
    </register>
    <rule attn_type="CS" node_inst="0:7">
        <!-- FIR & ~MASK & ~ACT0 & ~ACT1 -->
        <expr type="and">
            <expr type="reg" value1="EQ_QME_FIR"/>
            <expr type="not">
                <expr type="reg" value1="EQ_QME_FIR_MASK"/>
            </expr>
            <expr type="not">
                <expr type="reg" value1="EQ_QME_FIR_ACT0"/>
            </expr>
            <expr type="not">
                <expr type="reg" value1="EQ_QME_FIR_ACT1"/>
            </expr>
        </expr>
    </rule>
    <rule attn_type="RE" node_inst="0:7">
        <!-- FIR & ~MASK & ~ACT0 & ACT1 -->
        <expr type="and">
            <expr type="reg" value1="EQ_QME_FIR"/>
            <expr type="not">
                <expr type="reg" value1="EQ_QME_FIR_MASK"/>
            </expr>
            <expr type="not">
                <expr type="reg" value1="EQ_QME_FIR_ACT0"/>
            </expr>
            <expr type="reg" value1="EQ_QME_FIR_ACT1"/>
        </expr>
    </rule>
    <bit pos="0">PPE halted due to an error</bit>
    <bit pos="1">PPE asserted debug trigger</bit>
    <bit pos="2">Spare trigger for testing or workarounds</bit>
    <bit pos="3">PPE asserted a watchdog timeout condition</bit>
    <bit pos="4">QME hardware detected its own timeout on the PCB Slave interface</bit>
    <bit pos="5">Block Copy Engine or QME PPE direct access error from the Fabric</bit>
    <bit pos="6">SRAM Uncorrectable Error</bit>
    <bit pos="7">SRAM Correctable Error</bit>
    <bit pos="8">Resonant Clock Table array Parity Error</bit>
    <bit pos="9">PIG request of PCB interrupt before its previous interrupt completed</bit>
    <bit pos="10">Scrub timer tick occurred when scrub is still pending</bit>
    <bit pos="11">QME_LFIR_CTFS_ERR</bit>
    <bit pos="12">QME_LFIR_CPMS_ERR</bit>
    <bit pos="13">PGPE Heartbeat Lost from a hw deadman timer controlled by QHB</bit>
    <bit pos="14">BCE forward progress error</bit>
    <bit pos="15">Resclk TARGET_PSTATE Change Protocol Error</bit>
    <bit pos="16">PCB Network or Endpoint Reset occurred when QME was not halted</bit>
    <bit pos="17">Firmware cleared special wakeup request before SPECIAL_WKUP_DONE</bit>
    <bit pos="18">A new special wakeup right after previous cleared</bit>
    <bit pos="19">Core External Interrupt wakeup sources present but disabled by threads</bit>
    <bit pos="20">Core External Interrupt present but the chiplet is deconfigured</bit>
    <bit pos="21">Reserved</bit>
    <bit pos="22">PB read cmd waited too long for lost data (hang)</bit>
    <bit pos="23">PPE tried to write a protected addr as defined by the SWPR[n] register</bit>
    <bit pos="24">DTC Sequencer read a UE from SRAM</bit>
    <bit pos="25">Correctable error detected on incoming data for a PowerBus read</bit>
    <bit pos="26">UE Detected on incoming data for a PowerBus read</bit>
    <bit pos="27">SUE Detected on incoming data for a PowerBus read</bit>
    <bit pos="28">PB Request address hit an invalid entry in the TOPOLOGY XLATE TABLE</bit>
    <bit pos="29">Parity error detected on a powerbus tag</bit>
    <bit pos="30">Code attempted to write the PIG register when the previous request was still pending</bit>
    <bit pos="31">Local access error bit(s) set</bit>
    <bit pos="32">CE detected on read to the SSA located in QME powerbus routing logic</bit>
    <bit pos="33">UE detected on read to the SSA located in QME powerbus routing logic</bit>
    <bit pos="34">spare</bit>
    <bit pos="35">spare</bit>
</attn_node>