| #include "config.h" |
| |
| #include "mihawk-cpld.hpp" |
| |
| #include "gpio.hpp" |
| #include "utility.hpp" |
| |
| #include <errno.h> |
| #include <fcntl.h> |
| #include <sys/ioctl.h> |
| #include <unistd.h> |
| |
| #include <elog-errors.hpp> |
| #include <org/open_power/Witherspoon/Fault/error.hpp> |
| #include <phosphor-logging/elog.hpp> |
| #include <phosphor-logging/log.hpp> |
| #include <xyz/openbmc_project/Common/Device/error.hpp> |
| |
| #include <chrono> |
| #include <iostream> |
| #include <map> |
| #include <memory> |
| #include <string> |
| |
| // i2c bus & i2c slave address of Mihawk's CPLD_register |
| static constexpr uint8_t busId = 11; |
| static constexpr uint8_t slaveAddr = 0x40; |
| |
| // SMLink Status Register(Interrupt-control-bit Register) |
| static constexpr size_t StatusReg_1 = 0x20; |
| |
| // SMLink Status Register(Power-on error code Register) |
| static constexpr size_t StatusReg_2 = 0x21; |
| |
| // SMLink Status Register(Power-ready error code Register) |
| static constexpr size_t StatusReg_3 = 0x22; |
| |
| using namespace std; |
| |
| namespace phosphor |
| { |
| namespace power |
| { |
| const auto DEVICE_NAME = "MihawkCPLD"s; |
| |
| namespace fs = std::filesystem; |
| using namespace phosphor::logging; |
| |
| using namespace sdbusplus::org::open_power::Witherspoon::Fault::Error; |
| |
| MihawkCPLD::MihawkCPLD(size_t instance, sdbusplus::bus::bus& bus) : |
| Device(DEVICE_NAME, instance), bus(bus) |
| { |
| } |
| |
| void MihawkCPLD::onFailure() |
| { |
| bool poweronError = checkPoweronFault(); |
| |
| // If the interrupt of power_on_error is switch on, |
| // read CPLD_register error code to analyze |
| // and report the error log event. |
| if (poweronError) |
| { |
| ErrorCode code; |
| code = static_cast<ErrorCode>(readFromCPLDErrorCode(StatusReg_2)); |
| |
| switch (code) |
| { |
| case ErrorCode::_1: |
| report<ErrorCode1>(); |
| break; |
| case ErrorCode::_2: |
| report<ErrorCode2>(); |
| break; |
| case ErrorCode::_3: |
| report<ErrorCode3>(); |
| break; |
| case ErrorCode::_4: |
| report<ErrorCode4>(); |
| break; |
| case ErrorCode::_5: |
| report<ErrorCode5>(); |
| break; |
| case ErrorCode::_6: |
| report<ErrorCode6>(); |
| break; |
| case ErrorCode::_7: |
| report<ErrorCode7>(); |
| break; |
| case ErrorCode::_8: |
| report<ErrorCode8>(); |
| break; |
| case ErrorCode::_9: |
| report<ErrorCode9>(); |
| break; |
| case ErrorCode::_10: |
| report<ErrorCode10>(); |
| break; |
| case ErrorCode::_11: |
| report<ErrorCode11>(); |
| break; |
| case ErrorCode::_12: |
| report<ErrorCode12>(); |
| break; |
| case ErrorCode::_13: |
| report<ErrorCode13>(); |
| break; |
| case ErrorCode::_14: |
| report<ErrorCode14>(); |
| break; |
| case ErrorCode::_15: |
| report<ErrorCode15>(); |
| break; |
| case ErrorCode::_16: |
| report<ErrorCode16>(); |
| break; |
| case ErrorCode::_17: |
| report<ErrorCode17>(); |
| break; |
| case ErrorCode::_18: |
| report<ErrorCode18>(); |
| break; |
| case ErrorCode::_19: |
| report<ErrorCode19>(); |
| break; |
| case ErrorCode::_20: |
| report<ErrorCode20>(); |
| break; |
| case ErrorCode::_21: |
| report<ErrorCode21>(); |
| break; |
| case ErrorCode::_22: |
| report<ErrorCode22>(); |
| break; |
| case ErrorCode::_23: |
| report<ErrorCode23>(); |
| break; |
| case ErrorCode::_24: |
| report<ErrorCode24>(); |
| break; |
| case ErrorCode::_25: |
| report<ErrorCode25>(); |
| break; |
| case ErrorCode::_26: |
| report<ErrorCode26>(); |
| break; |
| case ErrorCode::_27: |
| report<ErrorCode27>(); |
| break; |
| case ErrorCode::_28: |
| report<ErrorCode28>(); |
| break; |
| case ErrorCode::_29: |
| report<ErrorCode29>(); |
| break; |
| case ErrorCode::_30: |
| report<ErrorCode30>(); |
| break; |
| case ErrorCode::_31: |
| report<ErrorCode31>(); |
| break; |
| case ErrorCode::_32: |
| report<ErrorCode32>(); |
| break; |
| case ErrorCode::_33: |
| report<ErrorCode33>(); |
| break; |
| case ErrorCode::_34: |
| report<ErrorCode34>(); |
| break; |
| case ErrorCode::_35: |
| report<ErrorCode35>(); |
| break; |
| case ErrorCode::_36: |
| report<ErrorCode36>(); |
| break; |
| default: |
| // If the errorcode isn't 1~36, |
| // it indicates that the CPLD register |
| // has a reading issue, |
| // so the errorcode0 error is reported. |
| report<ErrorCode0>(); |
| break; |
| } |
| clearCPLDregister(); |
| } |
| } |
| |
| void MihawkCPLD::analyze() |
| { |
| bool powerreadyError = checkPowerreadyFault(); |
| |
| // Use the function of GPIO class to check |
| // GPIOF0(CPLD uses). |
| using namespace phosphor::gpio; |
| GPIO gpio{"/dev/gpiochip0", static_cast<gpioNum_t>(40), Direction::input}; |
| |
| // Check GPIOFO pin whether is switched off. |
| // if GPIOF0 has been switched off, |
| // check CPLD's errorcode & report error. |
| if (gpio.read() == Value::low) |
| { |
| // If the interrupt of power_ready_error is switch on, |
| // read CPLD_register error code to analyze and |
| // report the error event. |
| if (powerreadyError) |
| { |
| ErrorCode code; |
| code = static_cast<ErrorCode>(readFromCPLDErrorCode(StatusReg_3)); |
| |
| if (!errorcodeMask) |
| { |
| // Check the errorcodeMask & errorcode whether |
| // are the same value to avoid to report the |
| // same error again. |
| switch (code) |
| { |
| case ErrorCode::_1: |
| report<ErrorCode1>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_2: |
| report<ErrorCode2>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_3: |
| report<ErrorCode3>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_4: |
| report<ErrorCode4>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_5: |
| report<ErrorCode5>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_6: |
| report<ErrorCode6>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_7: |
| report<ErrorCode7>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_8: |
| report<ErrorCode8>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_9: |
| report<ErrorCode9>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_10: |
| report<ErrorCode10>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_11: |
| report<ErrorCode11>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_12: |
| report<ErrorCode12>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_13: |
| report<ErrorCode13>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_14: |
| report<ErrorCode14>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_15: |
| report<ErrorCode15>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_16: |
| report<ErrorCode16>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_17: |
| report<ErrorCode17>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_18: |
| report<ErrorCode18>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_19: |
| report<ErrorCode19>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_20: |
| report<ErrorCode20>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_21: |
| report<ErrorCode21>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_22: |
| report<ErrorCode22>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_23: |
| report<ErrorCode23>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_24: |
| report<ErrorCode24>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_25: |
| report<ErrorCode25>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_26: |
| report<ErrorCode26>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_27: |
| report<ErrorCode27>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_28: |
| report<ErrorCode28>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_29: |
| report<ErrorCode29>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_30: |
| report<ErrorCode30>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_31: |
| report<ErrorCode31>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_32: |
| report<ErrorCode32>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_33: |
| report<ErrorCode33>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_34: |
| report<ErrorCode34>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_35: |
| report<ErrorCode35>(); |
| errorcodeMask = 1; |
| break; |
| case ErrorCode::_36: |
| report<ErrorCode36>(); |
| errorcodeMask = 1; |
| break; |
| default: |
| // If the errorcode is not 1~36, |
| // it indicates that the CPLD register |
| // has a reading issue, so the |
| // errorcode0 error is reported. |
| report<ErrorCode0>(); |
| errorcodeMask = 1; |
| break; |
| } |
| clearCPLDregister(); |
| } |
| } |
| } |
| |
| if (gpio.read() == Value::high) |
| { |
| // If there isn't an error(GPIOF0 |
| // which CPLD uses is switched on), |
| // we clear errorcodeMask. |
| errorcodeMask = 0; |
| } |
| } |
| |
| // Check for PoweronFault |
| bool MihawkCPLD::checkPoweronFault() |
| { |
| uint16_t statusValue_1; |
| bool result; |
| |
| if (!i2c) |
| { |
| openCPLDDevice(); |
| } |
| i2c->read(StatusReg_1, statusValue_1); |
| |
| if (statusValue_1 < 0) |
| { |
| std::cerr << "i2c->read() reads data failed \n"; |
| result = 0; |
| } |
| |
| if ((statusValue_1 >> 5) & 1) |
| { |
| // If power_on-interrupt-bit is read as 1, |
| // switch on the flag. |
| result = 1; |
| } |
| else |
| { |
| result = 0; |
| } |
| |
| // Return the flag. |
| return result; |
| } |
| |
| // Read CPLD_register error code and return the result to analyze. |
| int MihawkCPLD::readFromCPLDErrorCode(int statusReg) |
| { |
| uint16_t statusValue_2; |
| |
| if (!i2c) |
| { |
| openCPLDDevice(); |
| } |
| i2c->read(statusReg, statusValue_2); |
| |
| if (statusValue_2 < 0 || |
| ((statusValue_2 > static_cast<int>(ErrorCode::_35)) && |
| (statusValue_2 != static_cast<int>(ErrorCode::_36)))) |
| { |
| statusValue_2 = 0; |
| } |
| |
| // Return the data via i2c->read(). |
| return statusValue_2; |
| } |
| |
| // Check for PowerreadyFault |
| bool MihawkCPLD::checkPowerreadyFault() |
| { |
| uint16_t statusValue_3; |
| bool result; |
| |
| if (!i2c) |
| { |
| openCPLDDevice(); |
| } |
| i2c->read(StatusReg_1, statusValue_3); |
| |
| if (statusValue_3 < 0) |
| { |
| std::cerr << "i2c->read() reads data failed \n"; |
| result = 0; |
| } |
| |
| if ((statusValue_3 >> 6) & 1) |
| { |
| // If power_ready-interrupt-bit is read as 1, |
| // switch on the flag. |
| result = 1; |
| } |
| else |
| { |
| result = 0; |
| } |
| |
| // Return the flag. |
| return result; |
| } |
| |
| // Clear CPLD_register after reading. |
| void MihawkCPLD::clearCPLDregister() |
| { |
| uint16_t data = 0x01; |
| |
| if (!i2c) |
| { |
| openCPLDDevice(); |
| } |
| |
| // Write 0x01 to StatusReg_1 for clearing |
| // CPLD_register. |
| i2c->write(StatusReg_1, data); |
| } |
| |
| // Open i2c device(CPLD_register) |
| void MihawkCPLD::openCPLDDevice() |
| { |
| i2c = i2c::create(busId, slaveAddr); |
| } |
| |
| } // namespace power |
| } // namespace phosphor |