| { |
| "comments": [ "phosphor-regulators configuration file for IBM Rainier systems" ], |
| |
| |
| "rules": [ |
| { |
| "comments": [ "Rule to set PMBus PAGE to 0" ], |
| "id": "set_page0_rule", |
| "actions": [ |
| { "i2c_write_byte": { "register": "0x00", "value": "0x00" } } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to set PMBus PAGE to 1" ], |
| "id": "set_page1_rule", |
| "actions": [ |
| { "i2c_write_byte": { "register": "0x00", "value": "0x01" } } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to set output voltage of a PMBus regulator" ], |
| "id": "set_voltage_rule", |
| "actions": [ |
| { |
| "comments": [ "Write volts value to VOUT_COMMAND in linear format.", |
| "Get volts value from configuration. Get exponent", |
| "from VOUT_MODE. Verify write was successful." ], |
| "pmbus_write_vout_command": { "format": "linear", "is_verified": true } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to set output voltage of PAGE 0 of a PMBus regulator" ], |
| "id": "set_voltage_page0_rule", |
| "actions": [ |
| { "run_rule": "set_page0_rule" }, |
| { "run_rule": "set_voltage_rule" } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to set output voltage of PAGE 1 of a PMBus regulator" ], |
| "id": "set_voltage_page1_rule", |
| "actions": [ |
| { "run_rule": "set_page1_rule" }, |
| { "run_rule": "set_voltage_rule" } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to set output voltage of a PMBus regulator using", |
| "PMBus OPERATION and VOUT_COMMAND" ], |
| "id": "set_operation_and_voltage_rule", |
| "actions": [ |
| { |
| "comments": [ "Set PMBus OPERATION to 0x80 indicating output voltage", |
| "is set by the PMBus VOUT_COMMAND" ], |
| "i2c_write_byte": { "register": "0x01", "value": "0x80" } |
| }, |
| |
| { |
| "comments": [ "Set the output voltage using the PMBus VOUT_COMMAND" ], |
| "run_rule": "set_voltage_rule" |
| }, |
| |
| { |
| "comments": [ "Set PMBus OPERATION to 0xB0 indicating output voltage", |
| "will now be set by AVSBus (AVS_VOUT_COMMAND).", |
| "Hardware settings cause the VOUT_COMMAND value to be", |
| "the initial voltage value for AVSBus." ], |
| "i2c_write_byte": { "register": "0x01", "value": "0xB0" } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to set IOUT_OC_WARN_LIMIT for a PMBus regulator" ], |
| "id": "set_iout_oc_warn_limit_rule", |
| "actions": [ |
| { |
| "comments": [ "Set PMBus IOUT_OC_WARN_LIMIT to 326A to ensure OCW", |
| "asserts at the roll-over bug identified in the", |
| "silicon. 326A = 0x08A3. PMBus requires", |
| "the low order byte to be written first." ], |
| "i2c_write_bytes": { "register": "0x4A", "values": [ "0xA3", "0x08" ] } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to configure a VDD rail using the PMBus interface" ], |
| "id": "configure_vdd_rule", |
| "actions": [ |
| { "run_rule": "set_page0_rule" }, |
| { "run_rule": "set_iout_oc_warn_limit_rule" }, |
| { |
| "comments": [ "Set VOUT_MODE to exponent of -9 for VDD regulator", |
| "to support older and newer hardware." ], |
| "i2c_write_byte": { "register": "0x20", "value": "0x17" } |
| }, |
| { "run_rule": "set_operation_and_voltage_rule" }, |
| { |
| "comments": [ "Set VOUT_MIN to 0V since for VDD the voltage", |
| "can go down to 0.5V so we want to lower this", |
| "limit below 0.5V so the regulator does not trip." ], |
| "i2c_write_bytes": { "register": "0x2B", "values": [ "0x00", "0x00" ] } |
| }, |
| { |
| "comments": [ "Set VOUT_MAX to 1.255V since for VDD the voltage", |
| "can go up to 1.1V so we want to raise this", |
| "limit above 1.1V so the regulator does not trip." ], |
| "i2c_write_bytes": { "register": "0x24", "values": [ "0x83", "0x02" ] } |
| }, |
| { |
| "comments": [ "Set POWER_GOOD_ON for VDD to a value of 0.5V." ], |
| "i2c_write_bytes": { "register": "0x5E", "values": [ "0x00", "0x01" ] } |
| }, |
| { |
| "comments": [ "Set POWER_GOOD_OFF for VDD to a value of 0.4V." ], |
| "i2c_write_bytes": { "register": "0x5F", "values": [ "0xCD", "0x00" ] } |
| }, |
| { |
| "comments": [ "Set VOUT_OV_WARN_LIMIT for VDD to a value of 1.30V." ], |
| "i2c_write_bytes": { "register": "0x42", "values": [ "0x9A", "0x02" ] } |
| }, |
| { |
| "comments": [ "Set VOUT_UV_WARN_LIMIT for VDD to a value of 0.45V." ], |
| "i2c_write_bytes": { "register": "0x43", "values": [ "0xE6", "0x00" ] } |
| }, |
| { |
| "comments": [ "Set TOFF_FALL time for VDD to a value of 10ms." ], |
| "i2c_write_bytes": { "register": "0x65", "values": [ "0x28", "0xF0" ] } |
| }, |
| { |
| "comments": [ "Set IOUT_OC_FAULT_RESPONSE for VDD to shutdown." ], |
| "i2c_write_byte": { "register": "0x47", "value": "0xC0" } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to configure a VDN rail using the PMBus interface" ], |
| "id": "configure_vdn_rule", |
| "actions": [ |
| { "run_rule": "set_page0_rule" }, |
| { "run_rule": "set_operation_and_voltage_rule" }, |
| { |
| "comments": [ "Set VOUT_MIN to 0V since for VDN the voltage", |
| "can go down to 0.6V so we want to lower this", |
| "limit below 0.6V so the regulator does not trip." ], |
| "i2c_write_bytes": { "register": "0x2B", "values": [ "0x00", "0x00" ] } |
| }, |
| { |
| "comments": [ "Set VOUT_MAX to 1.1V since for VDN the voltage", |
| "can go up to 1.0V so we want to raise this", |
| "limit above 1.0V so the regulator does not trip." ], |
| "i2c_write_bytes": { "register": "0x24", "values": [ "0x33", "0x02" ] } |
| }, |
| { |
| "comments": [ "Set POWER_GOOD_ON for VDN to a value of 0.45V." ], |
| "i2c_write_bytes": { "register": "0x5E", "values": [ "0xE6", "0x00" ] } |
| }, |
| { |
| "comments": [ "Set POWER_GOOD_OFF for VDN to a value of 0.40V." ], |
| "i2c_write_bytes": { "register": "0x5F", "values": [ "0xCC", "0x00" ] } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to configure a VCS rail using the PMBus interface" ], |
| "id": "configure_vcs_rule", |
| "actions": [ |
| { "run_rule": "set_page1_rule" }, |
| { "run_rule": "set_operation_and_voltage_rule" }, |
| { |
| "comments": [ "Set VOUT_MIN to 0V since for VCS the voltage", |
| "can go down to 0.7V so we want to lower this", |
| "limit below 0.7V so the regulator does not trip." ], |
| "i2c_write_bytes": { "register": "0x2B", "values": [ "0x00", "0x00" ] } |
| }, |
| { |
| "comments": [ "Set VOUT_MAX to 1.2V since for VCS the voltage", |
| "can go up to 1.1V so we want to raise this", |
| "limit above 1.1V so the regulator does not trip." ], |
| "i2c_write_bytes": { "register": "0x24", "values": [ "0x66", "0x02" ] } |
| }, |
| { |
| "comments": [ "Set POWER_GOOD_ON for VCS to a value of 0.55V." ], |
| "i2c_write_bytes": { "register": "0x5E", "values": [ "0x19", "0x01" ] } |
| }, |
| { |
| "comments": [ "Set POWER_GOOD_OFF for VCS to a value of 0.50V." ], |
| "i2c_write_bytes": { "register": "0x5F", "values": [ "0x00", "0x01" ] } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to configure a VIO rail using the PMBus interface" ], |
| "id": "configure_vio_rule", |
| "actions": [ |
| { "run_rule": "set_page0_rule" }, |
| { "run_rule": "set_operation_and_voltage_rule" }, |
| { |
| "comments": [ "Set VOUT_MIN to 0V since for VIO the voltage", |
| "can go down to 0.8V so we want to lower this", |
| "limit below 0.8V so the regulator does not trip." ], |
| "i2c_write_bytes": { "register": "0x2B", "values": [ "0x00", "0x00" ] } |
| }, |
| { |
| "comments": [ "Set VOUT_MAX to 1.1V since for VIO the voltage", |
| "can go up to 1.0V so we want to raise this", |
| "limit above 1.0V so the regulator does not trip." ], |
| "i2c_write_bytes": { "register": "0x24", "values": [ "0x33", "0x02" ] } |
| }, |
| { |
| "comments": [ "Set POWER_GOOD_ON for VIO to a value of 0.55V." ], |
| "i2c_write_bytes": { "register": "0x5E", "values": [ "0x19", "0x01" ] } |
| }, |
| { |
| "comments": [ "Set POWER_GOOD_OFF for VIO to a value of 0.50V." ], |
| "i2c_write_bytes": { "register": "0x5F", "values": [ "0x00", "0x01" ] } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to configure a VPCIE rail using the PMBus interface" ], |
| "id": "configure_vpcie_rule", |
| "actions": [ |
| { "run_rule": "set_page0_rule" }, |
| { "run_rule": "set_voltage_rule" }, |
| { |
| "comments": [ "Set VOUT_MIN to 0V since for VPCIE the voltage", |
| "can go down to 0.81V so we want to lower this", |
| "limit below 0.81V so the regulator does not trip." ], |
| "i2c_write_bytes": { "register": "0x2B", "values": [ "0x00", "0x00" ] } |
| }, |
| { |
| "comments": [ "Set VOUT_MAX to 1.0V since for VPCIE the voltage", |
| "can go up to 0.91V so we want to raise this", |
| "limit above 0.91V so the regulator does not trip." ], |
| "i2c_write_bytes": { "register": "0x24", "values": [ "0x00", "0x02" ] } |
| }, |
| { |
| "comments": [ "Set POWER_GOOD_ON for VPCIE to a value of 0.65V." ], |
| "i2c_write_bytes": { "register": "0x5E", "values": [ "0x4C", "0x01" ] } |
| }, |
| { |
| "comments": [ "Set POWER_GOOD_OFF for VPCIE to a value of 0.60V." ], |
| "i2c_write_bytes": { "register": "0x5F", "values": [ "0x33", "0x01" ] } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to read sensors on IR38064 regulators using the", |
| "PMBus interface" ], |
| "id": "read_sensors_ir38064_rule", |
| "actions": [ |
| { |
| "comments": [ "Read output current from READ_IOUT" ], |
| "pmbus_read_sensor": { |
| "type": "iout", |
| "command": "0x8C", |
| "format": "linear_11" |
| } |
| }, |
| { |
| "comments": [ "Read highest output current from MFR_IOUT_PEAK" ], |
| "pmbus_read_sensor": { |
| "type": "iout_peak", |
| "command": "0xDC", |
| "format": "linear_11" |
| } |
| }, |
| { |
| "comments": [ "Read output power from READ_POUT" ], |
| "pmbus_read_sensor": { |
| "type": "pout", |
| "command": "0x96", |
| "format": "linear_11" |
| } |
| }, |
| { |
| "comments": [ "Read temperature from READ_TEMPERATURE" ], |
| "pmbus_read_sensor": { |
| "type": "temperature", |
| "command": "0x8D", |
| "format": "linear_11" |
| } |
| }, |
| { |
| "comments": [ "Read highest temperature from MFR_TEMPERATURE_PEAK" ], |
| "pmbus_read_sensor": { |
| "type": "temperature_peak", |
| "command": "0xDD", |
| "format": "linear_11" |
| } |
| }, |
| { |
| "comments": [ "Read output voltage from READ_VOUT.", |
| "Note: regulator does not support VOUT_MODE, so the", |
| "exponent must be specified." ], |
| "pmbus_read_sensor": { |
| "type": "vout", |
| "command": "0x8B", |
| "format": "linear_16", |
| "exponent": -8 |
| } |
| }, |
| { |
| "comments": [ "Read highest output voltage from MFR_VOUT_PEAK.", |
| "Note: regulator does not support VOUT_MODE, so the", |
| "exponent must be specified." ], |
| "pmbus_read_sensor": { |
| "type": "vout_peak", |
| "command": "0xDB", |
| "format": "linear_16", |
| "exponent": -8 |
| } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to read sensors on IR35221 regulators using the", |
| "PMBus interface" ], |
| "id": "read_sensors_ir35221_rule", |
| "actions": [ |
| { |
| "comments": [ "Read output current from READ_IOUT" ], |
| "pmbus_read_sensor": { |
| "type": "iout", |
| "command": "0x8C", |
| "format": "linear_11" |
| } |
| }, |
| { |
| "comments": [ "Read highest output current from MFR_IOUT_PEAK" ], |
| "pmbus_read_sensor": { |
| "type": "iout_peak", |
| "command": "0xC7", |
| "format": "linear_11" |
| } |
| }, |
| { |
| "comments": [ "Read lowest output current from MFR_IOUT_VALLEY" ], |
| "pmbus_read_sensor": { |
| "type": "iout_valley", |
| "command": "0xCB", |
| "format": "linear_11" |
| } |
| }, |
| { |
| "comments": [ "Read output power from READ_POUT" ], |
| "pmbus_read_sensor": { |
| "type": "pout", |
| "command": "0x96", |
| "format": "linear_11" |
| } |
| }, |
| { |
| "comments": [ "Read temperature from READ_TEMPERATURE_1" ], |
| "pmbus_read_sensor": { |
| "type": "temperature", |
| "command": "0x8D", |
| "format": "linear_11" |
| } |
| }, |
| { |
| "comments": [ "Read highest temperature from MFR_TEMP_PEAK" ], |
| "pmbus_read_sensor": { |
| "type": "temperature_peak", |
| "command": "0xC8", |
| "format": "linear_11" |
| } |
| }, |
| { |
| "comments": [ "Read output voltage from READ_VOUT" ], |
| "pmbus_read_sensor": { |
| "type": "vout", |
| "command": "0x8B", |
| "format": "linear_16" |
| } |
| }, |
| { |
| "comments": [ "Read highest output voltage from MFR_VOUT_PEAK" ], |
| "pmbus_read_sensor": { |
| "type": "vout_peak", |
| "command": "0xC6", |
| "format": "linear_16" |
| } |
| }, |
| { |
| "comments": [ "Read lowest output voltage from MFR_VOUT_VALLEY" ], |
| "pmbus_read_sensor": { |
| "type": "vout_valley", |
| "command": "0xCA", |
| "format": "linear_16" |
| } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to read sensors on PAGE 0 of IR35221 regulators", |
| "using the PMBus interface" ], |
| "id": "read_sensors_ir35221_page0_rule", |
| "actions": [ |
| { "run_rule": "set_page0_rule" }, |
| { "run_rule": "read_sensors_ir35221_rule" } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to read sensors on PAGE 1 of IR35221 regulators", |
| "using the PMBus interface" ], |
| "id": "read_sensors_ir35221_page1_rule", |
| "actions": [ |
| { "run_rule": "set_page1_rule" }, |
| { "run_rule": "read_sensors_ir35221_rule" } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to read sensors on PAGE 0 of XDPE132G5C regulators", |
| "using the PMBus interface" ], |
| "id": "read_sensors_xdpe132g5c_page0_rule", |
| "actions": [ |
| { |
| "comments": [ "Can use same rule as for IR35221 regulators" ], |
| "run_rule": "read_sensors_ir35221_page0_rule" |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to determine if the current system is a 2S4U/2S2U.", |
| "2S systems have more regulators on the Nisqually system", |
| "planar than 1S systems. Must return true if system is a", |
| "2S4U/2S2U and false if system is a 1S4U." ], |
| "id": "is_2s_system_rule", |
| "actions": [ |
| { |
| "comments": [ "Check whether the CCIN VPD keyword on the Nisqually", |
| "system planar has the value for 2S4U or 2S2U" ], |
| "or": [ |
| { "compare_vpd": { "fru": "system/chassis/motherboard", "keyword": "CCIN", "value": "2E2F" } }, |
| { "compare_vpd": { "fru": "system/chassis/motherboard", "keyword": "CCIN", "value": "2E2D" } } |
| ] |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to determine if pass 2 or higher Nisqually", |
| "backplane is present. Must return true if present and", |
| "false otherwise." ], |
| "id": "is_pass2_nisqually_rule", |
| "actions": [ |
| { |
| "comments": [ "Check that the PartNumber VPD keyword on the", |
| "Nisqually system planar is not the value for", |
| "the pass 1 2U or 4U." ], |
| "not": |
| { |
| "or": [ |
| { "compare_vpd": { "fru": "system/chassis/motherboard", "keyword": "PartNumber", "value": "02WG656" } }, |
| { "compare_vpd": { "fru": "system/chassis/motherboard", "keyword": "PartNumber", "value": "02WG678" } } |
| ] |
| } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to determine if the VRM FRU for DCM-1 is present.", |
| "Must return true if VRM is present and false if VRM is", |
| "missing." ], |
| "id": "is_dcm1_vrm_present_rule", |
| "actions": [ |
| { |
| "comments": [ "Check whether the VRM FRU is present OR the DCM-1", |
| "FRU is present. This provides a double check in", |
| "case the VRM presence line is not working. If DCM-1", |
| "is present, the associated VRM should be too." ], |
| "or": [ |
| { "compare_presence": { "fru": "system/chassis/motherboard/vdd_vrm1", "value": true } }, |
| { "compare_presence": { "fru": "system/chassis/motherboard/dcm1/cpu0", "value": true } } |
| ] |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to determine if a Flett card is present in slot C8.", |
| "This requires a Nisqually pass2+ due to I2C bus number", |
| "differences between pass 1 and pass 2.", |
| "Pass 1 and pass 2 Fletts are both supported.", |
| "Must return true if present and false otherwise." ], |
| "id": "is_flett_c8_present_rule", |
| "actions": [ |
| { |
| "if": { |
| "condition": { |
| "comments": [ "Check if the Nisqually is pass 2" ], |
| "run_rule": "is_pass2_nisqually_rule" |
| }, |
| "then": [ |
| { |
| "comments": [ "Check if a card is present in slot C8" ], |
| "if": { |
| "condition": { |
| "compare_presence": { |
| "fru": "system/chassis/motherboard/pcieslot8/pcie_card8", |
| "value": true |
| } |
| }, |
| "then": [ |
| { |
| "comments": [ "Check if card has Flett CCIN keyword" ], |
| "compare_vpd": { |
| "fru": "system/chassis/motherboard/pcieslot8/pcie_card8", |
| "keyword": "CCIN", |
| "value": "6B87" |
| } |
| } |
| ] |
| } |
| } |
| ] |
| } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to determine if a Flett card is present in slot C9.", |
| "This requires a Nisqually pass2+ due to I2C bus number", |
| "differences between pass 1 and pass 2.", |
| "This also requires the Flett to be pass 2 because the", |
| "pass 1 regulator has a different I2C address.", |
| "Must return true if present and false otherwise." ], |
| "id": "is_flett_c9_present_rule", |
| "actions": [ |
| { |
| "if": { |
| "condition": { |
| "comments": [ "Check if the Nisqually is pass 2" ], |
| "run_rule": "is_pass2_nisqually_rule" |
| }, |
| "then": [ |
| { |
| "comments": [ "Check if a card is present in slot C9" ], |
| "if": { |
| "condition": { |
| "compare_presence": { |
| "fru": "system/chassis/motherboard/pcieslot9/pcie_card9", |
| "value": true |
| } |
| }, |
| "then": [ |
| { |
| "comments": [ "Check if card has Flett CCIN keyword" ], |
| "if": { |
| "condition": { |
| "compare_vpd": { |
| "fru": "system/chassis/motherboard/pcieslot9/pcie_card9", |
| "keyword": "CCIN", |
| "value": "6B87" |
| } |
| }, |
| "then": [ |
| { |
| "comments": [ |
| "Check that card does not have a pass 1", |
| "part number" |
| ], |
| "not": { |
| "or": [ |
| { |
| "compare_vpd": { |
| "fru": "system/chassis/motherboard/pcieslot9/pcie_card9", |
| "keyword": "PartNumber", |
| "value": "03FL194" |
| } |
| }, |
| { |
| "compare_vpd": { |
| "fru": "system/chassis/motherboard/pcieslot9/pcie_card9", |
| "keyword": "PartNumber", |
| "value": "03FL204" |
| } |
| } |
| ] |
| } |
| } |
| ] |
| } |
| } |
| ] |
| } |
| } |
| ] |
| } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to determine if a Flett card is present in slot C10.", |
| "This requires a Nisqually pass2+ due to I2C bus number", |
| "differences between pass 1 and pass 2.", |
| "This also requires the Flett to be pass 2 because the", |
| "pass 1 regulator has a different I2C address.", |
| "Must return true if present and false otherwise." ], |
| "id": "is_flett_c10_present_rule", |
| "actions": [ |
| { |
| "if": { |
| "condition": { |
| "comments": [ "Check if the Nisqually is pass 2" ], |
| "run_rule": "is_pass2_nisqually_rule" |
| }, |
| "then": [ |
| { |
| "comments": [ "Check if a card is present in slot C10" ], |
| "if": { |
| "condition": { |
| "compare_presence": { |
| "fru": "system/chassis/motherboard/pcieslot10/pcie_card10", |
| "value": true |
| } |
| }, |
| "then": [ |
| { |
| "comments": [ "Check if card has Flett CCIN keyword" ], |
| "if": { |
| "condition": { |
| "compare_vpd": { |
| "fru": "system/chassis/motherboard/pcieslot10/pcie_card10", |
| "keyword": "CCIN", |
| "value": "6B87" |
| } |
| }, |
| "then": [ |
| { |
| "comments": [ |
| "Check that card does not have a pass 1", |
| "part number" |
| ], |
| "not": { |
| "or": [ |
| { |
| "compare_vpd": { |
| "fru": "system/chassis/motherboard/pcieslot10/pcie_card10", |
| "keyword": "PartNumber", |
| "value": "03FL194" |
| } |
| }, |
| { |
| "compare_vpd": { |
| "fru": "system/chassis/motherboard/pcieslot10/pcie_card10", |
| "keyword": "PartNumber", |
| "value": "03FL204" |
| } |
| } |
| ] |
| } |
| } |
| ] |
| } |
| } |
| ] |
| } |
| } |
| ] |
| } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Rule to determine if a Flett card is present in slot C11.", |
| "This requires a Nisqually pass2+ due to I2C bus number", |
| "differences between pass 1 and pass 2.", |
| "Pass 1 and pass 2 Fletts are both supported.", |
| "Must return true if present and false otherwise." ], |
| "id": "is_flett_c11_present_rule", |
| "actions": [ |
| { |
| "if": { |
| "condition": { |
| "comments": [ "Check if the Nisqually is pass 2" ], |
| "run_rule": "is_pass2_nisqually_rule" |
| }, |
| "then": [ |
| { |
| "comments": [ "Check if a card is present in slot C11" ], |
| "if": { |
| "condition": { |
| "compare_presence": { |
| "fru": "system/chassis/motherboard/pcieslot11/pcie_card11", |
| "value": true |
| } |
| }, |
| "then": [ |
| { |
| "comments": [ "Check if card has Flett CCIN keyword" ], |
| "compare_vpd": { |
| "fru": "system/chassis/motherboard/pcieslot11/pcie_card11", |
| "keyword": "CCIN", |
| "value": "6B87" |
| } |
| } |
| ] |
| } |
| } |
| ] |
| } |
| } |
| ] |
| } |
| ], |
| |
| |
| "chassis": [ |
| { |
| "comments": [ "Chassis (drawer) 1" ], |
| "number": 1, |
| "inventory_path": "system/chassis", |
| "devices": [ |
| { |
| "comments": [ "AVDD / IR38064: Primary PMBus Interface", |
| "In schematic: bus 4 (1-based), address 0xE2 (8-bit)" ], |
| "id": "avdd_regulator", |
| "is_regulator": true, |
| "fru": "system/chassis/motherboard", |
| "i2c_interface": { "bus": 3, "address": "0x71" }, |
| "presence_detection": { "rule_id": "is_pass2_nisqually_rule" }, |
| "rails": [ |
| { |
| "id": "avdd_rail", |
| "sensor_monitoring": { "rule_id": "read_sensors_ir38064_rule" } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "3.3VA / TPS549D22", |
| "In schematic: bus 9 (1-based), address 0x36 (8-bit)", |
| "Does not have power at standby; cannot be configured", |
| "Does not support the PMBus PAGE command" ], |
| "id": "3_3va_regulator", |
| "is_regulator": true, |
| "fru": "system/chassis/motherboard", |
| "i2c_interface": { "bus": 8, "address": "0x1B" }, |
| "rails": [ |
| { |
| "id": "3_3va_rail" |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "3.3VB / TPS549D22", |
| "In schematic: bus 4 (1-based), address 0x38 (8-bit)", |
| "Does not have power at standby; cannot be configured", |
| "Does not support the PMBus PAGE command" ], |
| "id": "3_3vb_regulator", |
| "is_regulator": true, |
| "fru": "system/chassis/motherboard", |
| "i2c_interface": { "bus": 3, "address": "0x1C" }, |
| "rails": [ |
| { |
| "id": "3_3vb_rail" |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "VDDp0 DCM 0 / XDPE132G5C: Primary PMBus Interface", |
| "In schematic: bus 10 (1-based), address 0xE2 (8-bit)" ], |
| "id": "vdd_p0_dcm0_regulator", |
| "is_regulator": true, |
| "fru": "system/chassis/motherboard/vdd_vrm0", |
| "i2c_interface": { "bus": 9, "address": "0x71" }, |
| "rails": [ |
| { |
| "id": "vdd_p0_dcm0_rail", |
| "configuration": { |
| "volts": 0.9, |
| "rule_id": "configure_vdd_rule" |
| }, |
| "sensor_monitoring": { "rule_id": "read_sensors_xdpe132g5c_page0_rule" } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "VDDp1 DCM 0 / XDPE132G5C: Primary PMBus Interface", |
| "In schematic: bus 10 (1-based), address 0xE0 (8-bit)" ], |
| "id": "vdd_p1_dcm0_regulator", |
| "is_regulator": true, |
| "fru": "system/chassis/motherboard/vdd_vrm0", |
| "i2c_interface": { "bus": 9, "address": "0x70" }, |
| "rails": [ |
| { |
| "id": "vdd_p1_dcm0_rail", |
| "configuration": { |
| "volts": 0.9, |
| "rule_id": "configure_vdd_rule" |
| }, |
| "sensor_monitoring": { "rule_id": "read_sensors_xdpe132g5c_page0_rule" } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "VDDp0 DCM 1 / XDPE132G5C: Primary PMBus Interface", |
| "In schematic: bus 11 (1-based), address 0xE2 (8-bit)" ], |
| "id": "vdd_p0_dcm1_regulator", |
| "is_regulator": true, |
| "fru": "system/chassis/motherboard/vdd_vrm1", |
| "i2c_interface": { "bus": 10, "address": "0x71" }, |
| "presence_detection": { "rule_id": "is_dcm1_vrm_present_rule" }, |
| "rails": [ |
| { |
| "id": "vdd_p0_dcm1_rail", |
| "configuration": { |
| "volts": 0.9, |
| "rule_id": "configure_vdd_rule" |
| }, |
| "sensor_monitoring": { "rule_id": "read_sensors_xdpe132g5c_page0_rule" } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "VDDp1 DCM 1 / XDPE132G5C: Primary PMBus Interface", |
| "In schematic: bus 11 (1-based), address 0xE0 (8-bit)" ], |
| "id": "vdd_p1_dcm1_regulator", |
| "is_regulator": true, |
| "fru": "system/chassis/motherboard/vdd_vrm1", |
| "i2c_interface": { "bus": 10, "address": "0x70" }, |
| "presence_detection": { "rule_id": "is_dcm1_vrm_present_rule" }, |
| "rails": [ |
| { |
| "id": "vdd_p1_dcm1_rail", |
| "configuration": { |
| "volts": 0.9, |
| "rule_id": "configure_vdd_rule" |
| }, |
| "sensor_monitoring": { "rule_id": "read_sensors_xdpe132g5c_page0_rule" } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "VDN & VCSp0 DCM 0 / IR35221: Primary PMBus Interface", |
| "In schematic: bus 10 (1-based), address 0xE4 (8-bit)" ], |
| "id": "vdn_vcs_p0_dcm0_regulator", |
| "is_regulator": true, |
| "fru": "system/chassis/motherboard", |
| "i2c_interface": { "bus": 9, "address": "0x72" }, |
| "rails": [ |
| { |
| "comments": [ "PMBus PAGE 0 rail" ], |
| "id": "vdn_dcm0_rail", |
| "configuration": { |
| "volts": 0.9, |
| "rule_id": "configure_vdn_rule" |
| }, |
| "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" } |
| }, |
| { |
| "comments": [ "PMBus PAGE 1 rail" ], |
| "id": "vcs_p0_dcm0_rail", |
| "configuration": { |
| "volts": 1.0, |
| "rule_id": "configure_vcs_rule" |
| }, |
| "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page1_rule" } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "VIO & VCSp1 DCM 0 / IR35221: Primary PMBus Interface", |
| "In schematic: bus 10 (1-based), address 0xE6 (8-bit)" ], |
| "id": "vio_vcs_p1_dcm0_regulator", |
| "is_regulator": true, |
| "fru": "system/chassis/motherboard", |
| "i2c_interface": { "bus": 9, "address": "0x73" }, |
| "rails": [ |
| { |
| "comments": [ "PMBus PAGE 0 rail" ], |
| "id": "vio_dcm0_rail", |
| "configuration": { |
| "volts": 1.02, |
| "rule_id": "configure_vio_rule" |
| }, |
| "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" } |
| }, |
| { |
| "comments": [ "PMBus PAGE 1 rail" ], |
| "id": "vcs_p1_dcm0_rail", |
| "configuration": { |
| "volts": 1.0, |
| "rule_id": "configure_vcs_rule" |
| }, |
| "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page1_rule" } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "VDN & VCSp0 DCM 1 / IR35221: Primary PMBus Interface", |
| "In schematic: bus 11 (1-based), address 0xE4 (8-bit)" ], |
| "id": "vdn_vcs_p0_dcm1_regulator", |
| "is_regulator": true, |
| "fru": "system/chassis/motherboard", |
| "i2c_interface": { "bus": 10, "address": "0x72" }, |
| "presence_detection": { "rule_id": "is_2s_system_rule" }, |
| "rails": [ |
| { |
| "comments": [ "PMBus PAGE 0 rail" ], |
| "id": "vdn_dcm1_rail", |
| "configuration": { |
| "volts": 0.9, |
| "rule_id": "configure_vdn_rule" |
| }, |
| "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" } |
| }, |
| { |
| "comments": [ "PMBus PAGE 1 rail" ], |
| "id": "vcs_p0_dcm1_rail", |
| "configuration": { |
| "volts": 1.0, |
| "rule_id": "configure_vcs_rule" |
| }, |
| "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page1_rule" } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "VIO & VCSp1 DCM 1 / IR35221: Primary PMBus Interface", |
| "In schematic: bus 11 (1-based), address 0xE6 (8-bit)" ], |
| "id": "vio_vcs_p1_dcm1_regulator", |
| "is_regulator": true, |
| "fru": "system/chassis/motherboard", |
| "i2c_interface": { "bus": 10, "address": "0x73" }, |
| "presence_detection": { "rule_id": "is_2s_system_rule" }, |
| "rails": [ |
| { |
| "comments": [ "PMBus PAGE 0 rail" ], |
| "id": "vio_dcm1_rail", |
| "configuration": { |
| "volts": 1.02, |
| "rule_id": "configure_vio_rule" |
| }, |
| "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" } |
| }, |
| { |
| "comments": [ "PMBus PAGE 1 rail" ], |
| "id": "vcs_p1_dcm1_rail", |
| "configuration": { |
| "volts": 1.0, |
| "rule_id": "configure_vcs_rule" |
| }, |
| "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page1_rule" } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "VPCIe DCM 0 / IR35221: Primary PMBus Interface", |
| "In schematic: bus 10 (1-based), address 0xE8 (8-bit)" ], |
| "id": "vpcie_dcm0_regulator", |
| "is_regulator": true, |
| "fru": "system/chassis/motherboard", |
| "i2c_interface": { "bus": 9, "address": "0x74" }, |
| "rails": [ |
| { |
| "id": "vpcie_dcm0_rail", |
| "configuration": { |
| "volts": 0.86, |
| "rule_id": "configure_vpcie_rule" |
| }, |
| "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "VPCIe DCM 1 / IR35221: Primary PMBus Interface", |
| "In schematic: bus 11 (1-based), address 0xE8 (8-bit)" ], |
| "id": "vpcie_dcm1_regulator", |
| "is_regulator": true, |
| "fru": "system/chassis/motherboard", |
| "i2c_interface": { "bus": 10, "address": "0x74" }, |
| "presence_detection": { "rule_id": "is_2s_system_rule" }, |
| "rails": [ |
| { |
| "id": "vpcie_dcm1_rail", |
| "configuration": { |
| "volts": 0.86, |
| "rule_id": "configure_vpcie_rule" |
| }, |
| "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Flett Slot C8 / IR35221: Primary PMBus Interface", |
| "In schematic: bus 7 (1-based) mux channel 3,", |
| "address 0xEC (8-bit).", |
| "BMC I2C bus alias 28" ], |
| "id": "flett_slot_c8_regulator", |
| "is_regulator": true, |
| "fru": "system/chassis/motherboard/pcieslot8/pcie_card8", |
| "i2c_interface": { "bus": 28, "address": "0x76" }, |
| "presence_detection": { "rule_id": "is_flett_c8_present_rule" }, |
| "rails": [ |
| { |
| "id": "flett_slot_c8_rail", |
| "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Flett Slot C9 / IR35221: Primary PMBus Interface", |
| "In schematic: bus 7 (1-based) mux channel 2,", |
| "address 0xEC (8-bit).", |
| "BMC I2C bus alias 27" ], |
| "id": "flett_slot_c9_regulator", |
| "is_regulator": true, |
| "fru": "system/chassis/motherboard/pcieslot9/pcie_card9", |
| "i2c_interface": { "bus": 27, "address": "0x76" }, |
| "presence_detection": { "rule_id": "is_flett_c9_present_rule" }, |
| "rails": [ |
| { |
| "id": "flett_slot_c9_rail", |
| "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Flett Slot C11 / IR35221: Primary PMBus Interface", |
| "In schematic: bus 12 (1-based) mux channel 1,", |
| "address 0xEC (8-bit).", |
| "BMC I2C bus alias 30" ], |
| "id": "flett_slot_c11_regulator", |
| "is_regulator": true, |
| "fru": "system/chassis/motherboard/pcieslot11/pcie_card11", |
| "i2c_interface": { "bus": 30, "address": "0x76" }, |
| "presence_detection": { "rule_id": "is_flett_c11_present_rule" }, |
| "rails": [ |
| { |
| "id": "flett_slot_c11_rail", |
| "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" } |
| } |
| ] |
| }, |
| |
| |
| { |
| "comments": [ "Flett Slot C10 / IR35221: Primary PMBus Interface", |
| "In schematic: bus 12 (1-based) mux channel 0,", |
| "address 0xEC (8-bit).", |
| "BMC I2C bus alias 29" ], |
| "id": "flett_slot_c10_regulator", |
| "is_regulator": true, |
| "fru": "system/chassis/motherboard/pcieslot10/pcie_card10", |
| "i2c_interface": { "bus": 29, "address": "0x76" }, |
| "presence_detection": { "rule_id": "is_flett_c10_present_rule" }, |
| "rails": [ |
| { |
| "id": "flett_slot_c10_rail", |
| "sensor_monitoring": { "rule_id": "read_sensors_ir35221_page0_rule" } |
| } |
| ] |
| } |
| ] |
| } |
| ] |
| } |
| |