| /** |
| * Copyright c 2020 IBM Corporation |
| * |
| * Licensed under the Apache License, Version 2.0 (the "License"); |
| * you may not use this file except in compliance with the License. |
| * You may obtain a copy of the License at |
| * |
| * http://www.apache.org/licenses/LICENSE-2.0 |
| * |
| * Unless required by applicable law or agreed to in writing, software |
| * distributed under the License is distributed on an "AS IS" BASIS, |
| * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| * See the License for the specific language governing permissions and |
| * limitations under the License. |
| */ |
| #include <errno.h> |
| #include <stdio.h> |
| #include <stdlib.h> |
| #include <sys/wait.h> |
| |
| #include <nlohmann/json.hpp> |
| |
| #include <fstream> |
| |
| #include <gtest/gtest.h> |
| |
| #define EXPECT_FILE_VALID(configFile) expectFileValid(configFile) |
| #define EXPECT_FILE_INVALID(configFile, expectedErrorMessage, \ |
| expectedOutputMessage) \ |
| expectFileInvalid(configFile, expectedErrorMessage, expectedOutputMessage) |
| #define EXPECT_JSON_VALID(configFileJson) expectJsonValid(configFileJson) |
| #define EXPECT_JSON_INVALID(configFileJson, expectedErrorMessage, \ |
| expectedOutputMessage) \ |
| expectJsonInvalid(configFileJson, expectedErrorMessage, \ |
| expectedOutputMessage) |
| |
| using json = nlohmann::json; |
| |
| const json validConfigFile = R"( |
| { |
| "comments": [ "Config file for a FooBar one-chassis system" ], |
| |
| "rules": [ |
| { |
| "comments": [ "Sets output voltage for a PMBus regulator rail" ], |
| "id": "set_voltage_rule", |
| "actions": [ |
| { |
| "pmbus_write_vout_command": { |
| "format": "linear" |
| } |
| } |
| ] |
| } |
| ], |
| |
| "chassis": [ |
| { |
| "comments": [ "Chassis number 1 containing CPUs and memory" ], |
| "number": 1, |
| "devices": [ |
| { |
| "comments": [ "IR35221 regulator producing the Vdd rail" ], |
| "id": "vdd_regulator", |
| "is_regulator": true, |
| "fru": "/system/chassis/motherboard/regulator1", |
| "i2c_interface": { |
| "bus": 1, |
| "address": "0x70" |
| }, |
| "rails": [ |
| { |
| "comments": [ "Vdd rail" ], |
| "id": "vdd", |
| "configuration": { |
| "volts": 1.03, |
| "rule_id": "set_voltage_rule" |
| }, |
| "sensor_monitoring": { |
| "rule_id": "read_sensors_rule" |
| } |
| } |
| ] |
| } |
| ] |
| } |
| ] |
| } |
| )"_json; |
| |
| std::string createTmpFile() |
| { |
| // create temporary file using mkstemp under /tmp/. random name for XXXXXX |
| char fileName[] = "/tmp/temp-XXXXXX"; |
| int fd = mkstemp(fileName); |
| if (fd == -1) |
| { |
| perror("Can't create temporary file"); |
| } |
| close(fd); |
| return fileName; |
| } |
| |
| std::string getValidationToolCommand(const std::string& configFileName) |
| { |
| std::string command = "python ../tools/validate-regulators-config.py -s \ |
| ../schema/config_schema.json -c "; |
| command += configFileName; |
| return command; |
| } |
| |
| int runToolForOutput(const std::string& configFileName, std::string& output, |
| bool isReadingStderr = false) |
| { |
| // run the validation tool with the temporary file and return the output |
| // of the validation tool. |
| std::string command = getValidationToolCommand(configFileName); |
| // reading the stderr while isReadingStderr is true. |
| if (isReadingStderr == true) |
| { |
| command += " 2>&1 >/dev/null"; |
| } |
| // get the jsonschema print from validation tool. |
| char buffer[256]; |
| std::string result = ""; |
| // to get the stdout from the validation tool. |
| FILE* pipe = popen(command.c_str(), "r"); |
| if (!pipe) |
| { |
| throw std::runtime_error("popen() failed!"); |
| } |
| while (!std::feof(pipe)) |
| { |
| if (fgets(buffer, sizeof buffer, pipe) != NULL) |
| { |
| result += buffer; |
| } |
| } |
| int returnValue = pclose(pipe); |
| // Check if pclose() failed |
| if (returnValue == -1) |
| { |
| // unable to close pipe. Print error and exit function. |
| throw std::runtime_error("pclose() failed!"); |
| } |
| std::string firstLine = result.substr(0, result.find('\n')); |
| output = firstLine; |
| // Get command exit status from return value |
| int exitStatus = WEXITSTATUS(returnValue); |
| return exitStatus; |
| } |
| |
| void expectFileValid(const std::string& configFileName) |
| { |
| std::string errorMessage = ""; |
| std::string outputMessage = ""; |
| EXPECT_EQ(runToolForOutput(configFileName, errorMessage, true), 0); |
| EXPECT_EQ(runToolForOutput(configFileName, outputMessage), 0); |
| EXPECT_EQ(errorMessage, ""); |
| EXPECT_EQ(outputMessage, ""); |
| } |
| |
| void expectFileInvalid(const std::string& configFileName, |
| const std::string& expectedErrorMessage, |
| const std::string& expectedOutputMessage) |
| { |
| std::string errorMessage = ""; |
| std::string outputMessage = ""; |
| EXPECT_EQ(runToolForOutput(configFileName, errorMessage, true), 1); |
| EXPECT_EQ(runToolForOutput(configFileName, outputMessage), 1); |
| EXPECT_EQ(errorMessage, expectedErrorMessage); |
| EXPECT_EQ(outputMessage, expectedOutputMessage); |
| } |
| |
| void expectJsonValid(const json configFileJson) |
| { |
| std::string fileName; |
| fileName = createTmpFile(); |
| std::string jsonData = configFileJson.dump(); |
| std::ofstream out(fileName); |
| out << jsonData; |
| out.close(); |
| |
| EXPECT_FILE_VALID(fileName); |
| unlink(fileName.c_str()); |
| } |
| |
| void expectJsonInvalid(const json configFileJson, |
| const std::string& expectedErrorMessage, |
| const std::string& expectedOutputMessage) |
| { |
| std::string fileName; |
| fileName = createTmpFile(); |
| std::string jsonData = configFileJson.dump(); |
| std::ofstream out(fileName); |
| out << jsonData; |
| out.close(); |
| |
| EXPECT_FILE_INVALID(fileName, expectedErrorMessage, expectedOutputMessage); |
| unlink(fileName.c_str()); |
| } |
| |
| TEST(ValidateRegulatorsConfigTest, Rule) |
| { |
| // valid test comments property, id property, |
| // action property specified. |
| { |
| json configFile = validConfigFile; |
| EXPECT_JSON_VALID(configFile); |
| } |
| |
| // valid test rule with no comments |
| { |
| json configFile = validConfigFile; |
| configFile["rules"][0].erase("comments"); |
| EXPECT_JSON_VALID(configFile); |
| } |
| |
| // invalid test comments property has invalid value type |
| { |
| json configFile = validConfigFile; |
| configFile["rules"][0]["comments"] = {1}; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'string'"); |
| } |
| |
| // invalid test rule with no ID |
| { |
| json configFile = validConfigFile; |
| configFile["rules"][0].erase("id"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'id' is a required property"); |
| } |
| |
| // invalid test id property has invalid value type (not string) |
| { |
| json configFile = validConfigFile; |
| configFile["rules"][0]["id"] = true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not of type u'string'"); |
| } |
| |
| // invalid test id property has invalid value |
| { |
| json configFile = validConfigFile; |
| configFile["rules"][0]["id"] = "foo%"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'foo%' does not match u'^[A-Za-z0-9_]+$'"); |
| } |
| |
| // invalid test rule with no actions property |
| { |
| json configFile = validConfigFile; |
| configFile["rules"][0].erase("actions"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'actions' is a required property"); |
| } |
| |
| // valid test rule with multiple actions |
| { |
| json configFile = validConfigFile; |
| configFile["rules"][0]["actions"][1]["run_rule"] = |
| "set_page0_voltage_rule"; |
| EXPECT_JSON_VALID(configFile); |
| } |
| |
| // invalid test actions property has invalid value type (not an array) |
| { |
| json configFile = validConfigFile; |
| configFile["rules"][0]["actions"] = 1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'array'"); |
| } |
| |
| // invalid test actions property has invalid value of action |
| { |
| json configFile = validConfigFile; |
| configFile["rules"][0]["actions"][0] = "foo"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'foo' is not of type u'object'"); |
| } |
| |
| // invalid test actions property has empty array |
| { |
| json configFile = validConfigFile; |
| configFile["rules"][0]["actions"] = json::array(); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "[] is too short"); |
| } |
| } |
| TEST(ValidateRegulatorsConfigTest, And) |
| { |
| // Valid. |
| { |
| json configFile = validConfigFile; |
| json andAction = |
| R"( |
| { |
| "and": [ |
| { "i2c_compare_byte": { "register": "0xA0", "value": "0x00" } }, |
| { "i2c_compare_byte": { "register": "0xA1", "value": "0x00" } } |
| ] |
| } |
| )"_json; |
| configFile["rules"][0]["actions"].push_back(andAction); |
| EXPECT_JSON_VALID(configFile); |
| } |
| |
| // Invalid: actions property value is an empty array. |
| { |
| json configFile = validConfigFile; |
| json andAction = |
| R"( |
| { |
| "and": [] |
| } |
| )"_json; |
| configFile["rules"][0]["actions"].push_back(andAction); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "[] is too short"); |
| } |
| |
| // Invalid: actions property has incorrect value data type. |
| { |
| json configFile = validConfigFile; |
| json andAction = |
| R"( |
| { |
| "and": true |
| } |
| )"_json; |
| configFile["rules"][0]["actions"].push_back(andAction); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not of type u'array'"); |
| } |
| |
| // Invalid: actions property value contains wrong element type |
| { |
| json configFile = validConfigFile; |
| json andAction = |
| R"( |
| { |
| "and": ["foo"] |
| } |
| )"_json; |
| configFile["rules"][0]["actions"].push_back(andAction); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'foo' is not of type u'object'"); |
| } |
| } |
| TEST(ValidateRegulatorsConfigTest, Chassis) |
| { |
| // Valid: test chassis. |
| { |
| json configFile = validConfigFile; |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Valid: test chassis with required properties. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0].erase("comments"); |
| configFile["chassis"][0].erase("devices"); |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Invalid: test chassis with no number. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0].erase("number"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'number' is a required property"); |
| } |
| // Invalid: test chassis with property comments wrong type. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["comments"] = true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not of type u'array'"); |
| } |
| // Invalid: test chassis with property number wrong type. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["number"] = 1.3; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1.3 is not of type u'integer'"); |
| } |
| // Invalid: test chassis with property devices wrong type. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"] = true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not of type u'array'"); |
| } |
| // Invalid: test chassis with property comments empty array. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["comments"] = json::array(); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "[] is too short"); |
| } |
| // Invalid: test chassis with property devices empty array. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"] = json::array(); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "[] is too short"); |
| } |
| // Invalid: test chassis with property number less than 1. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["number"] = 0; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "0 is less than the minimum of 1"); |
| } |
| } |
| TEST(ValidateRegulatorsConfigTest, ComparePresence) |
| { |
| json comparePresenceFile = validConfigFile; |
| comparePresenceFile["rules"][0]["actions"][1]["compare_presence"]["fru"] = |
| "/system/chassis/motherboard/regulator2"; |
| comparePresenceFile["rules"][0]["actions"][1]["compare_presence"]["value"] = |
| true; |
| // Valid. |
| { |
| json configFile = comparePresenceFile; |
| EXPECT_JSON_VALID(configFile); |
| } |
| |
| // Invalid: no FRU property. |
| { |
| json configFile = comparePresenceFile; |
| configFile["rules"][0]["actions"][1]["compare_presence"].erase("fru"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'fru' is a required property"); |
| } |
| |
| // Invalid: FRU property length is string less than 1. |
| { |
| json configFile = comparePresenceFile; |
| configFile["rules"][0]["actions"][1]["compare_presence"]["fru"] = ""; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'' is too short"); |
| } |
| |
| // Invalid: no value property. |
| { |
| json configFile = comparePresenceFile; |
| configFile["rules"][0]["actions"][1]["compare_presence"].erase("value"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'value' is a required property"); |
| } |
| |
| // Invalid: value property type is not boolean. |
| { |
| json configFile = comparePresenceFile; |
| configFile["rules"][0]["actions"][1]["compare_presence"]["value"] = "1"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'1' is not of type u'boolean'"); |
| } |
| |
| // Invalid: FRU property type is not string. |
| { |
| json configFile = comparePresenceFile; |
| configFile["rules"][0]["actions"][1]["compare_presence"]["fru"] = 1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'string'"); |
| } |
| } |
| TEST(ValidateRegulatorsConfigTest, CompareVpd) |
| { |
| json compareVpdFile = validConfigFile; |
| compareVpdFile["rules"][0]["actions"][1]["compare_vpd"]["fru"] = |
| "/system/chassis/motherboard/regulator2"; |
| compareVpdFile["rules"][0]["actions"][1]["compare_vpd"]["keyword"] = "CCIN"; |
| compareVpdFile["rules"][0]["actions"][1]["compare_vpd"]["value"] = "2D35"; |
| |
| // Valid. |
| { |
| json configFile = compareVpdFile; |
| EXPECT_JSON_VALID(configFile); |
| } |
| |
| // Invalid: no FRU property. |
| { |
| json configFile = compareVpdFile; |
| configFile["rules"][0]["actions"][1]["compare_vpd"].erase("fru"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'fru' is a required property"); |
| } |
| |
| // Invalid: no keyword property. |
| { |
| json configFile = compareVpdFile; |
| configFile["rules"][0]["actions"][1]["compare_vpd"].erase("keyword"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'keyword' is a required property"); |
| } |
| |
| // Invalid: no value property. |
| { |
| json configFile = compareVpdFile; |
| configFile["rules"][0]["actions"][1]["compare_vpd"].erase("value"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'value' is a required property"); |
| } |
| |
| // Invalid: property FRU wrong type. |
| { |
| json configFile = compareVpdFile; |
| configFile["rules"][0]["actions"][1]["compare_vpd"]["fru"] = 1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'string'"); |
| } |
| |
| // Invalid: property FRU is string less than 1. |
| { |
| json configFile = compareVpdFile; |
| configFile["rules"][0]["actions"][1]["compare_vpd"]["fru"] = ""; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'' is too short"); |
| } |
| |
| // Invalid: property keyword is not "CCIN", "Manufacturer", "Model", |
| // "PartNumber" |
| { |
| json configFile = compareVpdFile; |
| configFile["rules"][0]["actions"][1]["compare_vpd"]["keyword"] = |
| "Number"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'Number' is not one of [u'CCIN', " |
| "u'Manufacturer', u'Model', u'PartNumber']"); |
| } |
| |
| // Invalid: property value wrong type. |
| { |
| json configFile = compareVpdFile; |
| configFile["rules"][0]["actions"][1]["compare_vpd"]["value"] = 1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'string'"); |
| } |
| } |
| TEST(ValidateRegulatorsConfigTest, Device) |
| { |
| |
| // Valid: test devices. |
| { |
| json configFile = validConfigFile; |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Valid: test devices with required properties. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0].erase("comments"); |
| configFile["chassis"][0]["devices"][0].erase("presence_detection"); |
| configFile["chassis"][0]["devices"][0].erase("configuration"); |
| configFile["chassis"][0]["devices"][0].erase("rails"); |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Invalid: test devices with no id. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0].erase("id"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'id' is a required property"); |
| } |
| // Invalid: test devices with no is_regulator. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0].erase("is_regulator"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'is_regulator' is a required property"); |
| } |
| // Invalid: test devices with no fru. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0].erase("fru"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'fru' is a required property"); |
| } |
| // Invalid: test devices with no i2c_interface. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0].erase("i2c_interface"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'i2c_interface' is a required property"); |
| } |
| // Invalid: test devices with property comments wrong type. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0]["comments"] = true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not of type u'array'"); |
| } |
| // Invalid: test devices with property id wrong type. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0]["id"] = true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not of type u'string'"); |
| } |
| // Invalid: test devices with property is_regulator wrong type. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0]["is_regulator"] = 1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'boolean'"); |
| } |
| // Invalid: test devices with property fru wrong type. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0]["fru"] = true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not of type u'string'"); |
| } |
| // Invalid: test devices with property i2c_interface wrong type. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0]["i2c_interface"] = true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not of type u'object'"); |
| } |
| // Invalid: test devices with property presence_detection wrong |
| // type. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0]["presence_detection"] = true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not of type u'object'"); |
| } |
| // Invalid: test devices with property configuration wrong type. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0]["configuration"] = true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not of type u'object'"); |
| } |
| // Invalid: test devices with property rails wrong type. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0]["rails"] = true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not of type u'array'"); |
| } |
| // Invalid: test devices with property comments empty array. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0]["comments"] = json::array(); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "[] is too short"); |
| } |
| // Invalid: test devices with property fru length less than 1. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0]["fru"] = ""; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'' is too short"); |
| } |
| // Invalid: test devices with property id wrong format. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0]["id"] = "id#"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'id#' does not match u'^[A-Za-z0-9_]+$'"); |
| } |
| // Invalid: test devices with property rails empty array. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0]["rails"] = json::array(); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "[] is too short"); |
| } |
| } |
| TEST(ValidateRegulatorsConfigTest, I2CCompareBit) |
| { |
| json i2cCompareBitFile = validConfigFile; |
| i2cCompareBitFile["rules"][0]["actions"][1]["i2c_compare_bit"]["register"] = |
| "0xA0"; |
| i2cCompareBitFile["rules"][0]["actions"][1]["i2c_compare_bit"]["position"] = |
| 3; |
| i2cCompareBitFile["rules"][0]["actions"][1]["i2c_compare_bit"]["value"] = 1; |
| // Valid: test rule actions i2c_compare_bit. |
| { |
| json configFile = i2cCompareBitFile; |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Invalid: test i2c_compare_bit with no register. |
| { |
| json configFile = i2cCompareBitFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bit"].erase( |
| "register"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'register' is a required property"); |
| } |
| // Invalid: test i2c_compare_bit with no position. |
| { |
| json configFile = i2cCompareBitFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bit"].erase( |
| "position"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'position' is a required property"); |
| } |
| // Invalid: test i2c_compare_bit with no value. |
| { |
| json configFile = i2cCompareBitFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bit"].erase("value"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'value' is a required property"); |
| } |
| // Invalid: test i2c_compare_bit with register wrong type. |
| { |
| json configFile = i2cCompareBitFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bit"]["register"] = 1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'string'"); |
| } |
| // Invalid: test i2c_compare_bit with register wrong format. |
| { |
| json configFile = i2cCompareBitFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bit"]["register"] = |
| "0xA00"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0xA00' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_bit with position wrong type. |
| { |
| json configFile = i2cCompareBitFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bit"]["position"] = |
| 3.1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "3.1 is not of type u'integer'"); |
| } |
| // Invalid: test i2c_compare_bit with position greater than 7. |
| { |
| json configFile = i2cCompareBitFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bit"]["position"] = 8; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "8 is greater than the maximum of 7"); |
| } |
| // Invalid: test i2c_compare_bit with position less than 0. |
| { |
| json configFile = i2cCompareBitFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bit"]["position"] = |
| -1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "-1 is less than the minimum of 0"); |
| } |
| // Invalid: test i2c_compare_bit with value wrong type. |
| { |
| json configFile = i2cCompareBitFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bit"]["value"] = "1"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'1' is not of type u'integer'"); |
| } |
| // Invalid: test i2c_compare_bit with value greater than 1. |
| { |
| json configFile = i2cCompareBitFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bit"]["value"] = 2; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "2 is greater than the maximum of 1"); |
| } |
| // Invalid: test i2c_compare_bit with value less than 0. |
| { |
| json configFile = i2cCompareBitFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bit"]["value"] = -1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "-1 is less than the minimum of 0"); |
| } |
| } |
| TEST(ValidateRegulatorsConfigTest, I2CCompareByte) |
| { |
| json i2cCompareByteFile = validConfigFile; |
| i2cCompareByteFile["rules"][0]["actions"][1]["i2c_compare_byte"] |
| ["register"] = "0x82"; |
| i2cCompareByteFile["rules"][0]["actions"][1]["i2c_compare_byte"]["value"] = |
| "0x40"; |
| i2cCompareByteFile["rules"][0]["actions"][1]["i2c_compare_byte"]["mask"] = |
| "0x7F"; |
| // Valid: test i2c_compare_byte with all properties. |
| { |
| json configFile = i2cCompareByteFile; |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Valid: test i2c_compare_byte with all required properties. |
| { |
| json configFile = i2cCompareByteFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_byte"].erase("mask"); |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Invalid: test i2c_compare_byte with no register. |
| { |
| json configFile = i2cCompareByteFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_byte"].erase( |
| "register"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'register' is a required property"); |
| } |
| // Invalid: test i2c_compare_byte with no value. |
| { |
| json configFile = i2cCompareByteFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_byte"].erase("value"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'value' is a required property"); |
| } |
| // Invalid: test i2c_compare_byte with property register wrong type. |
| { |
| json configFile = i2cCompareByteFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_byte"]["register"] = |
| 1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'string'"); |
| } |
| // Invalid: test i2c_compare_byte with property value wrong type. |
| { |
| json configFile = i2cCompareByteFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_byte"]["value"] = 1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'string'"); |
| } |
| // Invalid: test i2c_compare_byte with property mask wrong type. |
| { |
| json configFile = i2cCompareByteFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_byte"]["mask"] = 1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'string'"); |
| } |
| // Invalid: test i2c_compare_byte with property register more than 2 hex |
| // digits. |
| { |
| json configFile = i2cCompareByteFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_byte"]["register"] = |
| "0x820"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0x820' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_byte with property value more than 2 hex |
| // digits. |
| { |
| json configFile = i2cCompareByteFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_byte"]["value"] = |
| "0x820"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0x820' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_byte with property mask more than 2 hex digits. |
| { |
| json configFile = i2cCompareByteFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_byte"]["mask"] = |
| "0x820"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0x820' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_byte with property register less than 2 hex |
| // digits. |
| { |
| json configFile = i2cCompareByteFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_byte"]["register"] = |
| "0x8"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0x8' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_byte with property value less than 2 hex |
| // digits. |
| { |
| json configFile = i2cCompareByteFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_byte"]["value"] = |
| "0x8"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0x8' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_byte with property mask less than 2 hex digits. |
| { |
| json configFile = i2cCompareByteFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_byte"]["mask"] = |
| "0x8"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0x8' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_byte with property register no leading prefix. |
| { |
| json configFile = i2cCompareByteFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_byte"]["register"] = |
| "82"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'82' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_byte with property value no leading prefix. |
| { |
| json configFile = i2cCompareByteFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_byte"]["value"] = |
| "82"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'82' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_byte with property mask no leading prefix. |
| { |
| json configFile = i2cCompareByteFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_byte"]["mask"] = "82"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'82' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_byte with property register invalid hex digit. |
| { |
| json configFile = i2cCompareByteFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_byte"]["register"] = |
| "0xG1"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0xG1' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_byte with property value invalid hex digit. |
| { |
| json configFile = i2cCompareByteFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_byte"]["value"] = |
| "0xG1"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0xG1' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_byte with property mask invalid hex digit. |
| { |
| json configFile = i2cCompareByteFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_byte"]["mask"] = |
| "0xG1"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0xG1' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| } |
| TEST(ValidateRegulatorsConfigTest, I2CCompareBytes) |
| { |
| json i2cCompareBytesFile = validConfigFile; |
| i2cCompareBytesFile["rules"][0]["actions"][1]["i2c_compare_bytes"] |
| ["register"] = "0x82"; |
| i2cCompareBytesFile["rules"][0]["actions"][1]["i2c_compare_bytes"] |
| ["values"] = {"0x02", "0x73"}; |
| i2cCompareBytesFile["rules"][0]["actions"][1]["i2c_compare_bytes"] |
| ["masks"] = {"0x7F", "0x7F"}; |
| // Valid: test i2c_compare_bytes. |
| { |
| json configFile = i2cCompareBytesFile; |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Valid: test i2c_compare_bytes with all required properties. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"].erase( |
| "masks"); |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Invalid: test i2c_compare_bytes with no register. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"].erase( |
| "register"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'register' is a required property"); |
| } |
| // Invalid: test i2c_compare_bytes with no values. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"].erase( |
| "values"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'values' is a required property"); |
| } |
| // Invalid: test i2c_compare_bytes with property values as empty array. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"]["values"] = |
| json::array(); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "[] is too short"); |
| } |
| // Invalid: test i2c_compare_bytes with property masks as empty array. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"]["masks"] = |
| json::array(); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "[] is too short"); |
| } |
| // Invalid: test i2c_compare_bytes with property register wrong type. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"]["register"] = |
| 1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'string'"); |
| } |
| // Invalid: test i2c_compare_bytes with property values wrong type. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"]["values"] = 1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'array'"); |
| } |
| // Invalid: test i2c_compare_bytes with property masks wrong type. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"]["masks"] = 1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'array'"); |
| } |
| // Invalid: test i2c_compare_bytes with property register more than 2 hex |
| // digits. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"]["register"] = |
| "0x820"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0x820' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_bytes with property values more than 2 hex |
| // digits. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"]["values"][0] = |
| "0x820"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0x820' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_bytes with property masks more than 2 hex |
| // digits. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"]["masks"][0] = |
| "0x820"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0x820' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_bytes with property register less than 2 hex |
| // digits. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"]["register"] = |
| "0x8"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0x8' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_bytes with property values less than 2 hex |
| // digits. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"]["values"][0] = |
| "0x8"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0x8' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_bytes with property masks less than 2 hex |
| // digits. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"]["masks"][0] = |
| "0x8"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0x8' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_bytes with property register no leading prefix. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"]["register"] = |
| "82"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'82' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_bytes with property values no leading prefix. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"]["values"][0] = |
| "82"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'82' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_bytes with property masks no leading prefix. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"]["masks"][0] = |
| "82"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'82' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_bytes with property register invalid hex digit. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"]["register"] = |
| "0xG1"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0xG1' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_bytes with property values invalid hex digit. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"]["values"][0] = |
| "0xG1"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0xG1' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| // Invalid: test i2c_compare_bytes with property masks invalid hex digit. |
| { |
| json configFile = i2cCompareBytesFile; |
| configFile["rules"][0]["actions"][1]["i2c_compare_bytes"]["masks"][0] = |
| "0xG1"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0xG1' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| } |
| TEST(ValidateRegulatorsConfigTest, I2CInterface) |
| { |
| // Valid: test i2c_interface. |
| { |
| json configFile = validConfigFile; |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Invalid: testi2c_interface with no bus. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0]["i2c_interface"].erase("bus"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'bus' is a required property"); |
| } |
| // Invalid: test i2c_interface with no address. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0]["i2c_interface"].erase( |
| "address"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'address' is a required property"); |
| } |
| // Invalid: test i2c_interface with property bus wrong type. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0]["i2c_interface"]["bus"] = true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not of type u'integer'"); |
| } |
| // Invalid: test i2c_interface with property address wrong |
| // type. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0]["i2c_interface"]["address"] = |
| true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not of type u'string'"); |
| } |
| // Invalid: test i2c_interface with property bus less than |
| // 0. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0]["i2c_interface"]["bus"] = -1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "-1 is less than the minimum of 0"); |
| } |
| // Invalid: test i2c_interface with property address wrong |
| // format. |
| { |
| json configFile = validConfigFile; |
| configFile["chassis"][0]["devices"][0]["i2c_interface"]["address"] = |
| "0x700"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0x700' does not match u'^0x[0-9A-Fa-f]{2}$'"); |
| } |
| } |
| TEST(ValidateRegulatorsConfigTest, If) |
| { |
| json ifFile = validConfigFile; |
| ifFile["rules"][0]["actions"][1]["if"]["condition"]["run_rule"] = |
| "is_downlevel_regulator"; |
| ifFile["rules"][0]["actions"][1]["if"]["then"][0]["run_rule"] = |
| "configure_downlevel_regulator"; |
| ifFile["rules"][0]["actions"][1]["if"]["else"][0]["run_rule"] = |
| "configure_downlevel_regulator"; |
| // Valid: test if. |
| { |
| json configFile = ifFile; |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Valid: test if with required properties. |
| { |
| json configFile = ifFile; |
| configFile["rules"][0]["actions"][1]["if"].erase("else"); |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Invalid: test if with no property condition. |
| { |
| json configFile = ifFile; |
| configFile["rules"][0]["actions"][1]["if"].erase("condition"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'condition' is a required property"); |
| } |
| // Invalid: test if with no property then. |
| { |
| json configFile = ifFile; |
| configFile["rules"][0]["actions"][1]["if"].erase("then"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'then' is a required property"); |
| } |
| // Invalid: test if with property then empty array. |
| { |
| json configFile = ifFile; |
| configFile["rules"][0]["actions"][1]["if"]["then"] = json::array(); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "[] is too short"); |
| } |
| // Invalid: test if with property else empty array. |
| { |
| json configFile = ifFile; |
| configFile["rules"][0]["actions"][1]["if"]["else"] = json::array(); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "[] is too short"); |
| } |
| // Invalid: test if with property condition wrong type. |
| { |
| json configFile = ifFile; |
| configFile["rules"][0]["actions"][1]["if"]["condition"] = 1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'object'"); |
| } |
| // Invalid: test if with property then wrong type. |
| { |
| json configFile = ifFile; |
| configFile["rules"][0]["actions"][1]["if"]["then"] = 1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'array'"); |
| } |
| // Invalid: test if with property else wrong type. |
| { |
| json configFile = ifFile; |
| configFile["rules"][0]["actions"][1]["if"]["else"] = 1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'array'"); |
| } |
| } |
| TEST(ValidateRegulatorsConfigTest, Not) |
| { |
| json notFile = validConfigFile; |
| notFile["rules"][0]["actions"][1]["not"]["i2c_compare_byte"]["register"] = |
| "0xA0"; |
| notFile["rules"][0]["actions"][1]["not"]["i2c_compare_byte"]["value"] = |
| "0xFF"; |
| // Valid: test not. |
| { |
| json configFile = notFile; |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Invalid: test not with wrong type. |
| { |
| json configFile = notFile; |
| configFile["rules"][0]["actions"][1]["not"] = 1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'object'"); |
| } |
| } |
| TEST(ValidateRegulatorsConfigTest, Or) |
| { |
| json orFile = validConfigFile; |
| orFile["rules"][0]["actions"][1]["or"][0]["i2c_compare_byte"]["register"] = |
| "0xA0"; |
| orFile["rules"][0]["actions"][1]["or"][0]["i2c_compare_byte"]["value"] = |
| "0x00"; |
| orFile["rules"][0]["actions"][1]["or"][1]["i2c_compare_byte"]["register"] = |
| "0xA1"; |
| orFile["rules"][0]["actions"][1]["or"][1]["i2c_compare_byte"]["value"] = |
| "0x00"; |
| // Valid: test or. |
| { |
| json configFile = orFile; |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Invalid: test or with empty array. |
| { |
| json configFile = orFile; |
| configFile["rules"][0]["actions"][1]["or"] = json::array(); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "[] is too short"); |
| } |
| // Invalid: test or with wrong type. |
| { |
| json configFile = orFile; |
| configFile["rules"][0]["actions"][1]["or"] = 1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'array'"); |
| } |
| } |
| TEST(ValidateRegulatorsConfigTest, PmbusReadSensor) |
| { |
| json pmbusReadSensorFile = validConfigFile; |
| pmbusReadSensorFile["rules"][0]["actions"][1]["pmbus_read_sensor"]["type"] = |
| "vout"; |
| pmbusReadSensorFile["rules"][0]["actions"][1]["pmbus_read_sensor"] |
| ["command"] = "0x8B"; |
| pmbusReadSensorFile["rules"][0]["actions"][1]["pmbus_read_sensor"] |
| ["format"] = "linear_16"; |
| pmbusReadSensorFile["rules"][0]["actions"][1]["pmbus_read_sensor"] |
| ["exponent"] = -8; |
| // Valid: test pmbus_read_sensor. |
| { |
| json configFile = pmbusReadSensorFile; |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Valid: test pmbus_read_sensor with required properties. |
| { |
| json configFile = pmbusReadSensorFile; |
| configFile["rules"][0]["actions"][1]["pmbus_read_sensor"].erase( |
| "exponent"); |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Invalid: test pmbus_read_sensor with no type. |
| { |
| json configFile = pmbusReadSensorFile; |
| configFile["rules"][0]["actions"][1]["pmbus_read_sensor"].erase("type"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'type' is a required property"); |
| } |
| // Invalid: test pmbus_read_sensor with no command. |
| { |
| json configFile = pmbusReadSensorFile; |
| configFile["rules"][0]["actions"][1]["pmbus_read_sensor"].erase( |
| "command"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'command' is a required property"); |
| } |
| // Invalid: test pmbus_read_sensor with no format. |
| { |
| json configFile = pmbusReadSensorFile; |
| configFile["rules"][0]["actions"][1]["pmbus_read_sensor"].erase( |
| "format"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'format' is a required property"); |
| } |
| // Invalid: test pmbus_read_sensor with property type wrong type. |
| { |
| json configFile = pmbusReadSensorFile; |
| configFile["rules"][0]["actions"][1]["pmbus_read_sensor"]["type"] = |
| true; |
| EXPECT_JSON_INVALID( |
| configFile, "Validation failed.", |
| "True is not one of [u'iout', u'iout_peak', u'iout_valley', " |
| "u'pout', u'temperature', u'temperature_peak', u'vout', " |
| "u'vout_peak', u'vout_valley']"); |
| } |
| // Invalid: test pmbus_read_sensor with property command wrong type. |
| { |
| json configFile = pmbusReadSensorFile; |
| configFile["rules"][0]["actions"][1]["pmbus_read_sensor"]["command"] = |
| true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not of type u'string'"); |
| } |
| // Invalid: test pmbus_read_sensor with property format wrong type. |
| { |
| json configFile = pmbusReadSensorFile; |
| configFile["rules"][0]["actions"][1]["pmbus_read_sensor"]["format"] = |
| true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not one of [u'linear_11', u'linear_16']"); |
| } |
| // Invalid: test pmbus_read_sensor with property exponent wrong type. |
| { |
| json configFile = pmbusReadSensorFile; |
| configFile["rules"][0]["actions"][1]["pmbus_read_sensor"]["exponent"] = |
| true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not of type u'integer'"); |
| } |
| // Invalid: test pmbus_read_sensor with property type wrong format. |
| { |
| json configFile = pmbusReadSensorFile; |
| configFile["rules"][0]["actions"][1]["pmbus_read_sensor"]["type"] = |
| "foo"; |
| EXPECT_JSON_INVALID( |
| configFile, "Validation failed.", |
| "u'foo' is not one of [u'iout', u'iout_peak', u'iout_valley', " |
| "u'pout', u'temperature', u'temperature_peak', u'vout', " |
| "u'vout_peak', u'vout_valley']"); |
| } |
| // Invalid: test pmbus_read_sensor with property command wrong format. |
| { |
| json configFile = pmbusReadSensorFile; |
| configFile["rules"][0]["actions"][1]["pmbus_read_sensor"]["command"] = |
| "0x8B0"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'0x8B0' does not match u'^0x[0-9a-fA-F]{2}$'"); |
| } |
| // Invalid: test pmbus_read_sensor with property format wrong format. |
| { |
| json configFile = pmbusReadSensorFile; |
| configFile["rules"][0]["actions"][1]["pmbus_read_sensor"]["format"] = |
| "foo"; |
| EXPECT_JSON_INVALID( |
| configFile, "Validation failed.", |
| "u'foo' is not one of [u'linear_11', u'linear_16']"); |
| } |
| } |
| TEST(ValidateRegulatorsConfigTest, PmbusWriteVoutCommand) |
| { |
| json pmbusWriteVoutCommandFile = validConfigFile; |
| pmbusWriteVoutCommandFile["rules"][0]["actions"][1] |
| ["pmbus_write_vout_command"]["volts"] = 1.03; |
| pmbusWriteVoutCommandFile["rules"][0]["actions"][1] |
| ["pmbus_write_vout_command"]["format"] = "linear"; |
| pmbusWriteVoutCommandFile["rules"][0]["actions"][1] |
| ["pmbus_write_vout_command"]["exponent"] = -8; |
| pmbusWriteVoutCommandFile["rules"][0]["actions"][1] |
| ["pmbus_write_vout_command"]["is_verified"] = true; |
| // Valid: test pmbus_write_vout_command. |
| { |
| json configFile = pmbusWriteVoutCommandFile; |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Valid: test pmbus_write_vout_command with required properties. |
| { |
| json configFile = pmbusWriteVoutCommandFile; |
| configFile["rules"][0]["actions"][1]["pmbus_write_vout_command"].erase( |
| "volts"); |
| configFile["rules"][0]["actions"][1]["pmbus_write_vout_command"].erase( |
| "exponent"); |
| configFile["rules"][0]["actions"][1]["pmbus_write_vout_command"].erase( |
| "is_verified"); |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Invalid: test pmbus_write_vout_command with no format. |
| { |
| json configFile = pmbusWriteVoutCommandFile; |
| configFile["rules"][0]["actions"][1]["pmbus_write_vout_command"].erase( |
| "format"); |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'format' is a required property"); |
| } |
| // Invalid: test pmbus_write_vout_command with property volts wrong type. |
| { |
| json configFile = pmbusWriteVoutCommandFile; |
| configFile["rules"][0]["actions"][1]["pmbus_write_vout_command"] |
| ["volts"] = true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not of type u'number'"); |
| } |
| // Invalid: test pmbus_write_vout_command with property format wrong type. |
| { |
| json configFile = pmbusWriteVoutCommandFile; |
| configFile["rules"][0]["actions"][1]["pmbus_write_vout_command"] |
| ["format"] = true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not one of [u'linear']"); |
| } |
| // Invalid: test pmbus_write_vout_command with property exponent wrong type. |
| { |
| json configFile = pmbusWriteVoutCommandFile; |
| configFile["rules"][0]["actions"][1]["pmbus_write_vout_command"] |
| ["exponent"] = 1.3; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1.3 is not of type u'integer'"); |
| } |
| // Invalid: test pmbus_write_vout_command with property is_verified wrong |
| // type. |
| { |
| json configFile = pmbusWriteVoutCommandFile; |
| configFile["rules"][0]["actions"][1]["pmbus_write_vout_command"] |
| ["is_verified"] = 1; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "1 is not of type u'boolean'"); |
| } |
| // Invalid: test pmbus_write_vout_command with property format wrong format. |
| { |
| json configFile = pmbusWriteVoutCommandFile; |
| configFile["rules"][0]["actions"][1]["pmbus_write_vout_command"] |
| ["format"] = "foo"; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "u'foo' is not one of [u'linear']"); |
| } |
| } |
| TEST(ValidateRegulatorsConfigTest, RunRule) |
| { |
| json runRuleFile = validConfigFile; |
| runRuleFile["rules"][0]["actions"][1]["run_rule"] = "set_voltage_rule1"; |
| // Valid: test run_rule. |
| { |
| json configFile = runRuleFile; |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Invalid: test run_rule wrong type. |
| { |
| json configFile = runRuleFile; |
| configFile["rules"][0]["actions"][1]["run_rule"] = true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not of type u'string'"); |
| } |
| // Invalid: test run_rule wrong format. |
| { |
| json configFile = runRuleFile; |
| configFile["rules"][0]["actions"][1]["run_rule"] = "set_voltage_rule%"; |
| EXPECT_JSON_INVALID( |
| configFile, "Validation failed.", |
| "u'set_voltage_rule%' does not match u'^[A-Za-z0-9_]+$'"); |
| } |
| } |
| TEST(ValidateRegulatorsConfigTest, SetDevice) |
| { |
| json setDeviceFile = validConfigFile; |
| setDeviceFile["rules"][0]["actions"][1]["set_device"] = "io_expander2"; |
| // Valid: test set_device. |
| { |
| json configFile = setDeviceFile; |
| EXPECT_JSON_VALID(configFile); |
| } |
| // Invalid: test set_device wrong type. |
| { |
| json configFile = setDeviceFile; |
| configFile["rules"][0]["actions"][1]["set_device"] = true; |
| EXPECT_JSON_INVALID(configFile, "Validation failed.", |
| "True is not of type u'string'"); |
| } |
| // Invalid: test set_device wrong format. |
| { |
| json configFile = setDeviceFile; |
| configFile["rules"][0]["actions"][1]["set_device"] = "io_expander2%"; |
| EXPECT_JSON_INVALID( |
| configFile, "Validation failed.", |
| "u'io_expander2%' does not match u'^[A-Za-z0-9_]+$'"); |
| } |
| } |