| ## Set this to pull in Axone only code (such as P9A/EXP MSS code) |
| set AXONE |
| |
| # Allows us to put in workarounds specifically for Axone bringup |
| set AXONE_BRING_UP |
| |
| # The BMC MBOX Protocol is used to access PNOR |
| unset SFC_IS_AST2500 |
| unset SFC_IS_AST2400 |
| set PNORDD_IS_BMCMBOX |
| unset PNORDD_IS_SFC |
| unset BMC_DOES_SFC_INIT |
| unset SFC_IS_IBM_DPSS |
| set ALLOW_MICRON_PNOR |
| set ALLOW_MACRONIX_PNOR |
| |
| |
| # Force DJVPD read/write to use EEPROM layer instead of old-style VPD cache |
| set DJVPD_READ_FROM_HW |
| set DJVPD_WRITE_TO_HW |
| unset DJVPD_READ_FROM_PNOR |
| unset DJVPD_WRITE_TO_PNOR |
| |
| # Force MEMVPD read/write to EEPROM layer instead of old-style VPD cache |
| # ( No concept of MEMVPD in Axone so should not matter ) |
| set MEMVPD_READ_FROM_HW |
| set MEMVPD_WRITE_TO_HW |
| unset MEMVPD_READ_FROM_PNOR |
| unset MEMVPD_WRITE_TO_PNOR |
| |
| # Force MVPD read/write to use EEPROM layer instead of old-style VPD cache |
| set MVPD_READ_FROM_HW |
| set MVPD_WRITE_TO_HW |
| unset MVPD_READ_FROM_PNOR |
| unset MVPD_WRITE_TO_PNOR |
| |
| # Other VPD options. |
| set PVPD_READ_FROM_HW |
| set PVPD_WRITE_TO_HW |
| unset PVPD_READ_FROM_PNOR |
| unset PVPD_WRITE_TO_PNOR |
| unset CDIMM_FORMAT_FOR_CVPD |
| |
| #enable EEPROM caching |
| set SUPPORT_EEPROM_CACHING |
| |
| # gpio config |
| set GPIODD |
| unset PALMETTO_VDDR |
| |
| # Enable Consecutive SBE Updates |
| set SBE_UPDATE_CONSECUTIVE |
| unset SBE_UPDATE_INDEPENDENT |
| unset SBE_UPDATE_SEQUENTIAL |
| unset SBE_UPDATE_SIMULTANEOUS |
| unset NO_SBE_UPDATES |
| |
| unset PCIE_HOTPLUG_CONTROLLER |
| |
| # turn on console output |
| set CONSOLE |
| set BMC_AST2500 |
| |
| unset DISABLE_HOSTBOOT_RUNTIME |
| |
| # Compile in hostboot runtime PRD |
| set HBRT_PRD |
| |
| # Compile in hb rt HTMGT : Load/Start OCC |
| set HTMGT |
| set START_OCC_DURING_BOOT |
| unset CONSOLE_OUTPUT_OCC_COMM |
| |
| #PNOR flags |
| unset PNOR_TWO_SIDE_SUPPORT |
| |
| set BMC_BT_LPC_IPMI |
| |
| # Enable Checkstop Analysis for both |
| # Runtime and IPLtime scenarios |
| set ENABLE_CHECKSTOP_ANALYSIS |
| set IPLTIME_CHECKSTOP_ANALYSIS |
| |
| # set for trace debug to console |
| unset CONSOLE_OUTPUT_TRACE |
| set CONSOLE_OUTPUT_FFDCDISPLAY |
| |
| # Terminate Hostboot when errors occur in manufacturing mode |
| # (relies on BMC to not trigger reboot) |
| unset HANG_ON_MFG_SRC_TERM |