| Mike Baiocchi | cce400e | 2020-04-27 11:27:25 -0500 | [diff] [blame] | 1 | ## Set this to pull in Axone only code (such as P9A/EXP MSS code) |
| 2 | set AXONE |
| 3 | |
| 4 | # Allows us to put in workarounds specifically for Axone bringup |
| 5 | set AXONE_BRING_UP |
| 6 | |
| 7 | # The BMC MBOX Protocol is used to access PNOR |
| 8 | unset SFC_IS_AST2500 |
| 9 | unset SFC_IS_AST2400 |
| 10 | set PNORDD_IS_BMCMBOX |
| 11 | unset PNORDD_IS_SFC |
| 12 | unset BMC_DOES_SFC_INIT |
| 13 | unset SFC_IS_IBM_DPSS |
| 14 | set ALLOW_MICRON_PNOR |
| 15 | set ALLOW_MACRONIX_PNOR |
| 16 | |
| 17 | |
| 18 | # Force DJVPD read/write to use EEPROM layer instead of old-style VPD cache |
| 19 | set DJVPD_READ_FROM_HW |
| 20 | set DJVPD_WRITE_TO_HW |
| 21 | unset DJVPD_READ_FROM_PNOR |
| 22 | unset DJVPD_WRITE_TO_PNOR |
| 23 | |
| 24 | # Force MEMVPD read/write to EEPROM layer instead of old-style VPD cache |
| 25 | # ( No concept of MEMVPD in Axone so should not matter ) |
| 26 | set MEMVPD_READ_FROM_HW |
| 27 | set MEMVPD_WRITE_TO_HW |
| 28 | unset MEMVPD_READ_FROM_PNOR |
| 29 | unset MEMVPD_WRITE_TO_PNOR |
| 30 | |
| 31 | # Force MVPD read/write to use EEPROM layer instead of old-style VPD cache |
| 32 | set MVPD_READ_FROM_HW |
| 33 | set MVPD_WRITE_TO_HW |
| 34 | unset MVPD_READ_FROM_PNOR |
| 35 | unset MVPD_WRITE_TO_PNOR |
| 36 | |
| 37 | # Other VPD options. |
| 38 | set PVPD_READ_FROM_HW |
| 39 | set PVPD_WRITE_TO_HW |
| 40 | unset PVPD_READ_FROM_PNOR |
| 41 | unset PVPD_WRITE_TO_PNOR |
| 42 | unset CDIMM_FORMAT_FOR_CVPD |
| 43 | |
| 44 | #enable EEPROM caching |
| 45 | set SUPPORT_EEPROM_CACHING |
| 46 | |
| 47 | # gpio config |
| 48 | set GPIODD |
| 49 | unset PALMETTO_VDDR |
| 50 | |
| 51 | # Enable Consecutive SBE Updates |
| 52 | set SBE_UPDATE_CONSECUTIVE |
| 53 | unset SBE_UPDATE_INDEPENDENT |
| 54 | unset SBE_UPDATE_SEQUENTIAL |
| 55 | unset SBE_UPDATE_SIMULTANEOUS |
| 56 | unset NO_SBE_UPDATES |
| 57 | |
| 58 | unset PCIE_HOTPLUG_CONTROLLER |
| 59 | |
| 60 | # turn on console output |
| 61 | set CONSOLE |
| 62 | set BMC_AST2500 |
| 63 | |
| 64 | unset DISABLE_HOSTBOOT_RUNTIME |
| 65 | |
| 66 | # Compile in hostboot runtime PRD |
| 67 | set HBRT_PRD |
| 68 | |
| 69 | # Compile in hb rt HTMGT : Load/Start OCC |
| 70 | set HTMGT |
| 71 | set START_OCC_DURING_BOOT |
| 72 | unset CONSOLE_OUTPUT_OCC_COMM |
| 73 | |
| 74 | #PNOR flags |
| 75 | unset PNOR_TWO_SIDE_SUPPORT |
| 76 | |
| 77 | set BMC_BT_LPC_IPMI |
| 78 | |
| 79 | # Enable Checkstop Analysis for both |
| 80 | # Runtime and IPLtime scenarios |
| 81 | set ENABLE_CHECKSTOP_ANALYSIS |
| 82 | set IPLTIME_CHECKSTOP_ANALYSIS |
| 83 | |
| 84 | # set for trace debug to console |
| 85 | unset CONSOLE_OUTPUT_TRACE |
| 86 | set CONSOLE_OUTPUT_FFDCDISPLAY |
| 87 | |
| 88 | # Terminate Hostboot when errors occur in manufacturing mode |
| 89 | # (relies on BMC to not trigger reboot) |
| 90 | unset HANG_ON_MFG_SRC_TERM |