meta-xilinx/meta-xilinx-bsp/conf/local.conf.sample - stefanberger/openbmc - Gitiles

 #
 # This file is your local configuration file and is where all local user settings
 # are placed. The comments in this file give some guide to the options a new user
 # to the system might want to change but pretty much any configuration option can
 # be set in this file. More adventurous users can look at local.conf.extended
 # which contains other examples of configuration which can be placed in this file
 # but new users likely won't need any of them initially.
 #
 # Lines starting with the '#' character are commented out and in some cases the
 # default values are provided as comments to show people example syntax. Enabling
 # the option is a question of removing the # character and making any change to the
 # variable as required.

 # BASE = "${COREBASE}/../.."

 #
 # Machine Selection
 #
 # You need to select a specific machine to target the build with. There are a selection
 # of emulated machines available which can boot and run in the QEMU emulator:
 #
 # This sets the default machine if no other machine is selected:
 MACHINE ??= "qemuzynq"

 #
 # Where to place downloads
 #
 # During a first build the system will download many different source code tarballs
 # from various upstream projects. This can take a while, particularly if your network
 # connection is slow. These are all stored in DL_DIR. When wiping and rebuilding you
 # can preserve this directory to speed up this part of subsequent builds. This directory
 # is safe to share between multiple builds on the same machine too.
 #
 # The default is a downloads directory under TOPDIR which is the build directory.
 #
 # DL_DIR ?= "${BASE}/downloads"

 #
 # Where to place shared-state files
 #
 # BitBake has the capability to accelerate builds based on previously built output.
 # This is done using "shared state" files which can be thought of as cache objects
 # and this option determines where those files are placed.
 #
 # You can wipe out TMPDIR leaving this directory intact and the build would regenerate
 # from these files if no changes were made to the configuration. If changes were made
 # to the configuration, only shared state files where the state was still valid would
 # be used (done using checksums).
 #
 # The default is a sstate-cache directory under TOPDIR.
 #
 # SSTATE_DIR ?= "${BASE}/sstate-cache"

 #
 # Where to place the build output
 #
 # This option specifies where the bulk of the building work should be done and
 # where BitBake should place its temporary files and output. Keep in mind that
 # this includes the extraction and compilation of many applications and the toolchain
 # which can use Gigabytes of hard disk space.
 #
 # The default is a tmp directory under TOPDIR.
 #
 #TMPDIR = "${TOPDIR}/tmp"
 #
 #TMPDIR_versal = "${TOPDIR}/tmp-versal"

 #
 # Default policy config
 #
 # The distribution setting controls which policy settings are used as defaults.
 # The default value is fine for general Yocto project use, at least initially.
 # Ultimately when creating custom policy, people will likely end up subclassing
 # these defaults.
 #
 DISTRO ?= "petalinux"

 #
 # Package Management configuration
 #
 # This variable lists which packaging formats to enable. Multiple package backends
 # can be enabled at once and the first item listed in the variable will be used
 # to generate the root filesystems.
 # Options are:
 #  - 'package_deb' for debian style deb files
 #  - 'package_ipk' for ipk files are used by opkg (a debian style embedded package manager)
 #  - 'package_rpm' for rpm style packages
 # E.g.: PACKAGE_CLASSES ?= "package_rpm package_deb package_ipk"
 # We default to ipk:
 PACKAGE_CLASSES ?= "package_rpm"

 #
 # SDK/ADT target architecture
 #
 # This variable specifies the architecture to build SDK/ADT items for and means
 # you can build the SDK packages for architectures other than the machine you are
 # running the build on (i.e. building i686 packages on an x86_64 host).
 # Supported values are i686 and x86_64
 #SDKMACHINE ?= "i686"

 #
 # Extra image configuration defaults
 #
 # The EXTRA_IMAGE_FEATURES variable allows extra packages to be added to the generated
 # images. Some of these options are added to certain image types automatically. The
 # variable can contain the following options:
 #  "dbg-pkgs"       - add -dbg packages for all installed packages
 #                     (adds symbol information for debugging/profiling)
 #  "dev-pkgs"       - add -dev packages for all installed packages
 #                     (useful if you want to develop against libs in the image)
 #  "ptest-pkgs"     - add -ptest packages for all ptest-enabled packages
 #                     (useful if you want to run the package test suites)
 #  "tools-sdk"      - add development tools (gcc, make, pkgconfig etc.)
 #  "tools-debug"    - add debugging tools (gdb, strace)
 #  "eclipse-debug"  - add Eclipse remote debugging support
 #  "tools-profile"  - add profiling tools (oprofile, exmap, lttng, valgrind)
 #  "tools-testapps" - add useful testing tools (ts_print, aplay, arecord etc.)
 #  "debug-tweaks"   - make an image suitable for development
 #                     e.g. ssh root access has a blank password
 # There are other application targets that can be used here too, see
 # meta/classes/image.bbclass and meta/classes/core-image.bbclass for more details.
 # We default to enabling the debugging tweaks.
 EXTRA_IMAGE_FEATURES = "debug-tweaks"

 #
 # Additional image features
 #
 # The following is a list of additional classes to use when building images which
 # enable extra features. Some available options which can be included in this variable
 # are:
 #   - 'buildstats' collect build statistics
 #   - 'image-mklibs' to reduce shared library files size for an image
 #   - 'image-prelink' in order to prelink the filesystem image
 #   - 'image-swab' to perform host system intrusion detection
 # NOTE: if listing mklibs & prelink both, then make sure mklibs is before prelink
 # NOTE: mklibs also needs to be explicitly enabled for a given image, see local.conf.extended
 USER_CLASSES ?= "buildstats image-mklibs"

 #
 # Runtime testing of images
 #
 # The build system can test booting virtual machine images under qemu (an emulator)
 # after any root filesystems are created and run tests against those images. To
 # enable this uncomment this line. See classes/testimage(-auto).bbclass for
 # further details.
 #TEST_IMAGE = "1"
 #
 # Interactive shell configuration
 #
 # Under certain circumstances the system may need input from you and to do this it
 # can launch an interactive shell. It needs to do this since the build is
 # multithreaded and needs to be able to handle the case where more than one parallel
 # process may require the user's attention. The default is iterate over the available
 # terminal types to find one that works.
 #
 # Examples of the occasions this may happen are when resolving patches which cannot
 # be applied, to use the devshell or the kernel menuconfig
 #
 # Supported values are auto, gnome, xfce, rxvt, screen, konsole (KDE 3.x only), none
 # Note: currently, Konsole support only works for KDE 3.x due to the way
 # newer Konsole versions behave
 #OE_TERMINAL = "auto"
 # By default disable interactive patch resolution (tasks will just fail instead):
 PATCHRESOLVE = "noop"

 #
 # Disk Space Monitoring during the build
 #
 # Monitor the disk space during the build. If there is less that 1GB of space or less
 # than 100K inodes in any key build location (TMPDIR, DL_DIR, SSTATE_DIR), gracefully
 # shutdown the build. If there is less that 100MB or 1K inodes, perform a hard abort
 # of the build. The reason for this is that running completely out of space can corrupt
 # files and damages the build in ways which may not be easily recoverable.
 # It's necesary to monitor /tmp, if there is no space left the build will fail
 # with very exotic errors.
 BB_DISKMON_DIRS = "\
     STOPTASKS,${TMPDIR},1G,100K \
     STOPTASKS,${DL_DIR},1G,100K \
     STOPTASKS,${SSTATE_DIR},1G,100K \
     STOPTASKS,/tmp,100M,100K \
     ABORT,${TMPDIR},100M,1K \
     ABORT,${DL_DIR},100M,1K \
     ABORT,${SSTATE_DIR},100M,1K \
     ABORT,/tmp,10M,1K"

 #
 # Shared-state files from other locations
 #
 # As mentioned above, shared state files are prebuilt cache data objects which can
 # used to accelerate build time. This variable can be used to configure the system
 # to search other mirror locations for these objects before it builds the data itself.
 #
 # This can be a filesystem directory, or a remote url such as http or ftp. These
 # would contain the sstate-cache results from previous builds (possibly from other
 # machines). This variable works like fetcher MIRRORS/PREMIRRORS and points to the
 # cache locations to check for the shared objects.
 # NOTE: if the mirror uses the same structure as SSTATE_DIR, you need to add PATH
 # at the end as shown in the examples below. This will be substituted with the
 # correct path within the directory structure.
 #SSTATE_MIRRORS ?= "\
 #file://.* http://someserver.tld/share/sstate/PATH;downloadfilename=PATH \n \
 #file://.* file:///some/local/dir/sstate/PATH"

 XILINX_VER_MAIN = "2020.2"

 # Uncomment below lines to provide path for custom xsct trim
 # This is required for building Versal based devices, please fetch the
 # xsct-trim from Xilinx lounge area
 #
 #EXTERNAL_XSCT_TARBALL = "/proj/yocto/xsct-trim/2020.2_xsct_daily_latest"
 #VALIDATE_XSCT_CHECKSUM = '0'

 # XILINX_VIVADO_DESIGN_SUIT should point to the Vivado installation directly if you are using xilinx-mcs recipe in meta-xilinx-tools
 #XILINX_VIVADO_DESIGN_SUIT = "/proj/xbuilds/2018.3_daily_latest/installs/lin64/Vivado/2018.3"

 # INHERIT += "externalsrc"
 # PREFERRED_PROVIDER_virtual/kernel = "linux-xlnx-dev"
 # EXTERNALSRC_pn-linux-xlnx-dev = "${BASE}/sources/linux"
 # RM_WORK_EXCLUDE += "linux-xlnx-dev"

 # PREFERRED_PROVIDER_virtual/bootloader = "u-boot-xlnx-dev"
 # EXTERNALSRC_pn-u-boot-xlnx-dev = "${BASE}/sources/u-boot"
 # RM_WORK_EXCLUDE += "u-boot-xlnx-dev"

 #Add below lines to use runqemu for ZU+ machines
 PMU_FIRMWARE_DEPLOY_DIR ??= "${DEPLOY_DIR_IMAGE}"
 PMU_FIRMWARE_IMAGE_NAME ??= "pmu-firmware-${MACHINE}"

 # CONF_VERSION is increased each time build/conf/ changes incompatibly and is used to
 # track the version of this file when it was generated. This can safely be ignored if
 # this doesn't mean anything to you.
 CONF_VERSION = "1"

 #Enable the below line to use pmu-rom.elf from a specific path
 #PMU_ROM = "/proj/yocto/pmu-rom/pmu-rom.elf"
	#
	# This file is your local configuration file and is where all local user settings
	# are placed. The comments in this file give some guide to the options a new user
	# to the system might want to change but pretty much any configuration option can
	# be set in this file. More adventurous users can look at local.conf.extended
	# which contains other examples of configuration which can be placed in this file
	# but new users likely won't need any of them initially.
	#
	# Lines starting with the '#' character are commented out and in some cases the
	# default values are provided as comments to show people example syntax. Enabling
	# the option is a question of removing the # character and making any change to the
	# variable as required.

	# BASE = "${COREBASE}/../.."

	#
	# Machine Selection
	#
	# You need to select a specific machine to target the build with. There are a selection
	# of emulated machines available which can boot and run in the QEMU emulator:
	#
	# This sets the default machine if no other machine is selected:
	MACHINE ??= "qemuzynq"

	#
	# Where to place downloads
	#
	# During a first build the system will download many different source code tarballs
	# from various upstream projects. This can take a while, particularly if your network
	# connection is slow. These are all stored in DL_DIR. When wiping and rebuilding you
	# can preserve this directory to speed up this part of subsequent builds. This directory
	# is safe to share between multiple builds on the same machine too.
	#
	# The default is a downloads directory under TOPDIR which is the build directory.
	#
	# DL_DIR ?= "${BASE}/downloads"

	#
	# Where to place shared-state files
	#
	# BitBake has the capability to accelerate builds based on previously built output.
	# This is done using "shared state" files which can be thought of as cache objects
	# and this option determines where those files are placed.
	#
	# You can wipe out TMPDIR leaving this directory intact and the build would regenerate
	# from these files if no changes were made to the configuration. If changes were made
	# to the configuration, only shared state files where the state was still valid would
	# be used (done using checksums).
	#
	# The default is a sstate-cache directory under TOPDIR.
	#
	# SSTATE_DIR ?= "${BASE}/sstate-cache"

	#
	# Where to place the build output
	#
	# This option specifies where the bulk of the building work should be done and
	# where BitBake should place its temporary files and output. Keep in mind that
	# this includes the extraction and compilation of many applications and the toolchain
	# which can use Gigabytes of hard disk space.
	#
	# The default is a tmp directory under TOPDIR.
	#
	#TMPDIR = "${TOPDIR}/tmp"
	#
	#TMPDIR_versal = "${TOPDIR}/tmp-versal"

	#
	# Default policy config
	#
	# The distribution setting controls which policy settings are used as defaults.
	# The default value is fine for general Yocto project use, at least initially.
	# Ultimately when creating custom policy, people will likely end up subclassing
	# these defaults.
	#
	DISTRO ?= "petalinux"

	#
	# Package Management configuration
	#
	# This variable lists which packaging formats to enable. Multiple package backends
	# can be enabled at once and the first item listed in the variable will be used
	# to generate the root filesystems.
	# Options are:
	# - 'package_deb' for debian style deb files
	# - 'package_ipk' for ipk files are used by opkg (a debian style embedded package manager)
	# - 'package_rpm' for rpm style packages
	# E.g.: PACKAGE_CLASSES ?= "package_rpm package_deb package_ipk"
	# We default to ipk:
	PACKAGE_CLASSES ?= "package_rpm"

	#
	# SDK/ADT target architecture
	#
	# This variable specifies the architecture to build SDK/ADT items for and means
	# you can build the SDK packages for architectures other than the machine you are
	# running the build on (i.e. building i686 packages on an x86_64 host).
	# Supported values are i686 and x86_64
	#SDKMACHINE ?= "i686"

	#
	# Extra image configuration defaults
	#
	# The EXTRA_IMAGE_FEATURES variable allows extra packages to be added to the generated
	# images. Some of these options are added to certain image types automatically. The
	# variable can contain the following options:
	# "dbg-pkgs" - add -dbg packages for all installed packages
	# (adds symbol information for debugging/profiling)
	# "dev-pkgs" - add -dev packages for all installed packages
	# (useful if you want to develop against libs in the image)
	# "ptest-pkgs" - add -ptest packages for all ptest-enabled packages
	# (useful if you want to run the package test suites)
	# "tools-sdk" - add development tools (gcc, make, pkgconfig etc.)
	# "tools-debug" - add debugging tools (gdb, strace)
	# "eclipse-debug" - add Eclipse remote debugging support
	# "tools-profile" - add profiling tools (oprofile, exmap, lttng, valgrind)
	# "tools-testapps" - add useful testing tools (ts_print, aplay, arecord etc.)
	# "debug-tweaks" - make an image suitable for development
	# e.g. ssh root access has a blank password
	# There are other application targets that can be used here too, see
	# meta/classes/image.bbclass and meta/classes/core-image.bbclass for more details.
	# We default to enabling the debugging tweaks.
	EXTRA_IMAGE_FEATURES = "debug-tweaks"

	#
	# Additional image features
	#
	# The following is a list of additional classes to use when building images which
	# enable extra features. Some available options which can be included in this variable
	# are:
	# - 'buildstats' collect build statistics
	# - 'image-mklibs' to reduce shared library files size for an image
	# - 'image-prelink' in order to prelink the filesystem image
	# - 'image-swab' to perform host system intrusion detection
	# NOTE: if listing mklibs & prelink both, then make sure mklibs is before prelink
	# NOTE: mklibs also needs to be explicitly enabled for a given image, see local.conf.extended
	USER_CLASSES ?= "buildstats image-mklibs"

	#
	# Runtime testing of images
	#
	# The build system can test booting virtual machine images under qemu (an emulator)
	# after any root filesystems are created and run tests against those images. To
	# enable this uncomment this line. See classes/testimage(-auto).bbclass for
	# further details.
	#TEST_IMAGE = "1"
	#
	# Interactive shell configuration
	#
	# Under certain circumstances the system may need input from you and to do this it
	# can launch an interactive shell. It needs to do this since the build is
	# multithreaded and needs to be able to handle the case where more than one parallel
	# process may require the user's attention. The default is iterate over the available
	# terminal types to find one that works.
	#
	# Examples of the occasions this may happen are when resolving patches which cannot
	# be applied, to use the devshell or the kernel menuconfig
	#
	# Supported values are auto, gnome, xfce, rxvt, screen, konsole (KDE 3.x only), none
	# Note: currently, Konsole support only works for KDE 3.x due to the way
	# newer Konsole versions behave
	#OE_TERMINAL = "auto"
	# By default disable interactive patch resolution (tasks will just fail instead):
	PATCHRESOLVE = "noop"

	#
	# Disk Space Monitoring during the build
	#
	# Monitor the disk space during the build. If there is less that 1GB of space or less
	# than 100K inodes in any key build location (TMPDIR, DL_DIR, SSTATE_DIR), gracefully
	# shutdown the build. If there is less that 100MB or 1K inodes, perform a hard abort
	# of the build. The reason for this is that running completely out of space can corrupt
	# files and damages the build in ways which may not be easily recoverable.
	# It's necesary to monitor /tmp, if there is no space left the build will fail
	# with very exotic errors.
	BB_DISKMON_DIRS = "\
	STOPTASKS,${TMPDIR},1G,100K \
	STOPTASKS,${DL_DIR},1G,100K \
	STOPTASKS,${SSTATE_DIR},1G,100K \
	STOPTASKS,/tmp,100M,100K \
	ABORT,${TMPDIR},100M,1K \
	ABORT,${DL_DIR},100M,1K \
	ABORT,${SSTATE_DIR},100M,1K \
	ABORT,/tmp,10M,1K"

	#
	# Shared-state files from other locations
	#
	# As mentioned above, shared state files are prebuilt cache data objects which can
	# used to accelerate build time. This variable can be used to configure the system
	# to search other mirror locations for these objects before it builds the data itself.
	#
	# This can be a filesystem directory, or a remote url such as http or ftp. These
	# would contain the sstate-cache results from previous builds (possibly from other
	# machines). This variable works like fetcher MIRRORS/PREMIRRORS and points to the
	# cache locations to check for the shared objects.
	# NOTE: if the mirror uses the same structure as SSTATE_DIR, you need to add PATH
	# at the end as shown in the examples below. This will be substituted with the
	# correct path within the directory structure.
	#SSTATE_MIRRORS ?= "\
	#file://.* http://someserver.tld/share/sstate/PATH;downloadfilename=PATH \n \
	#file://.* file:///some/local/dir/sstate/PATH"

	XILINX_VER_MAIN = "2020.2"

	# Uncomment below lines to provide path for custom xsct trim
	# This is required for building Versal based devices, please fetch the
	# xsct-trim from Xilinx lounge area
	#
	#EXTERNAL_XSCT_TARBALL = "/proj/yocto/xsct-trim/2020.2_xsct_daily_latest"
	#VALIDATE_XSCT_CHECKSUM = '0'

	# XILINX_VIVADO_DESIGN_SUIT should point to the Vivado installation directly if you are using xilinx-mcs recipe in meta-xilinx-tools
	#XILINX_VIVADO_DESIGN_SUIT = "/proj/xbuilds/2018.3_daily_latest/installs/lin64/Vivado/2018.3"

	# INHERIT += "externalsrc"
	# PREFERRED_PROVIDER_virtual/kernel = "linux-xlnx-dev"
	# EXTERNALSRC_pn-linux-xlnx-dev = "${BASE}/sources/linux"
	# RM_WORK_EXCLUDE += "linux-xlnx-dev"

	# PREFERRED_PROVIDER_virtual/bootloader = "u-boot-xlnx-dev"
	# EXTERNALSRC_pn-u-boot-xlnx-dev = "${BASE}/sources/u-boot"
	# RM_WORK_EXCLUDE += "u-boot-xlnx-dev"

	#Add below lines to use runqemu for ZU+ machines
	PMU_FIRMWARE_DEPLOY_DIR ??= "${DEPLOY_DIR_IMAGE}"
	PMU_FIRMWARE_IMAGE_NAME ??= "pmu-firmware-${MACHINE}"

	# CONF_VERSION is increased each time build/conf/ changes incompatibly and is used to
	# track the version of this file when it was generated. This can safely be ignored if
	# this doesn't mean anything to you.
	CONF_VERSION = "1"

	#Enable the below line to use pmu-rom.elf from a specific path
	#PMU_ROM = "/proj/yocto/pmu-rom/pmu-rom.elf"