import-layers/yocto-poky/documentation/ref-manual/ref-kickstart.xml

<!DOCTYPE chapter PUBLIC "-//OASIS//DTD DocBook XML V4.2//EN"
"http://www.oasis-open.org/docbook/xml/4.2/docbookx.dtd"
[<!ENTITY % poky SYSTEM "../poky.ent"> %poky; ] >

<chapter id='ref-kickstart'>
<title>OpenEmbedded Kickstart (<filename>.wks</filename>) Reference</title>

    <section id='openembedded-kickstart-wks-reference'>
        <title>Introduction</title>

        <para>
            The current Wic implementation supports only the basic kickstart
            partitioning commands:
            <filename>partition</filename> (or <filename>part</filename>
            for short) and <filename>bootloader</filename>.
            <note>
                Future updates will implement more commands and options.
                If you use anything that is not specifically supported, results
                can be unpredictable.
            </note>
        </para>

        <para>
            This chapter provides a reference on the available kickstart
            commands.
            The information lists the commands, their syntax, and meanings.
            Kickstart commands are based on the Fedora kickstart versions but
            with modifications to reflect Wic capabilities.
            You can see the original documentation for those commands at the
            following links:
            <itemizedlist>
                <listitem><para>
                    <ulink url='http://fedoraproject.org/wiki/Anaconda/Kickstart#part_or_partition'>http://fedoraproject.org/wiki/Anaconda/Kickstart#part_or_partition</ulink>
                    </para></listitem>
                <listitem><para>
                    <ulink url='http://fedoraproject.org/wiki/Anaconda/Kickstart#bootloader'>http://fedoraproject.org/wiki/Anaconda/Kickstart#bootloader</ulink>
                    </para></listitem>
            </itemizedlist>
        </para>
    </section>

    <section id='command-part-or-partition'>
        <title>Command: part or partition</title>

        <para>
            Either of these commands create a partition on the system and use
            the following syntax:
            <literallayout class='monospaced'>
     part [<replaceable>mntpoint</replaceable>]
     partition [<replaceable>mntpoint</replaceable>]
            </literallayout>
            If you do not provide <replaceable>mntpoint</replaceable>, Wic
            creates a partition but does not mount it.
        </para>

        <para>
            The <filename><replaceable>mntpoint</replaceable></filename> is
            where the partition will be mounted and must be of one of the
            following forms:
            <itemizedlist>
                <listitem><para>
                    <filename>/<replaceable>path</replaceable></filename>:
                    For example, "/", "/usr", or "/home"
                    </para></listitem>
                <listitem><para>
                    <filename>swap</filename>:
                    The created partition is used as swap space.
                    </para></listitem>
            </itemizedlist>
        </para>

        <para>
            Specifying a <replaceable>mntpoint</replaceable> causes the
            partition to automatically be mounted.
            Wic achieves this by adding entries to the filesystem table (fstab)
            during image generation.
            In order for wic to generate a valid fstab, you must also provide
            one of the <filename>--ondrive</filename>,
            <filename>--ondisk</filename>, or
            <filename>--use-uuid</filename> partition options as part of the
            command.
            Here is an example using "/" as the mountpoint.
            The command uses "--ondisk" to force the partition onto the
            <filename>sdb</filename> disk:
            <literallayout class='monospaced'>
     part / --source rootfs --ondisk sdb --fstype=ext3 --label platform --align 1024
            </literallayout>
        </para>

        <para>
            Here is a list that describes other supported options you can use
            with the <filename>part</filename> and
            <filename>partition</filename> commands:
            <itemizedlist>
                <listitem><para>
                    <emphasis><filename>--size</filename>:</emphasis>
                    The minimum partition size in MBytes.
                    Specify an integer value such as 500.
                    Do not append the number with "MB".
                    You do not need this option if you use
                    <filename>--source</filename>.
                    </para></listitem>
                <listitem><para>
                    <emphasis><filename>--source</filename>:</emphasis>
                    This option is a Wic-specific option that names the source
                    of the data that populates the partition.
                    The most common value for this option is "rootfs", but you
                    can use any value that maps to a valid source plug-in.
                    For information on the source plug-ins, see the
                    "<link linkend='wic-plug-ins-interface'>Wic Plug-Ins Interface</link>"
                    section.</para>

                    <para>If you use <filename>--source rootfs</filename>, Wic
                    creates a partition as large as needed and to fill it with
                    the contents of the root filesystem pointed to by the
                    <filename>-r</filename> command-line option or the
                    equivalent rootfs derived from the <filename>-e</filename>
                    command-line option.
                    The filesystem type used to create the partition is driven
                    by the value of the <filename>--fstype</filename> option
                    specified for the partition.
                    See the entry on <filename>--fstype</filename> that follows
                    for more information.</para>

                    <para>If you use
                    <filename>--source <replaceable>plugin-name</replaceable></filename>,
                    Wic creates a partition as large as needed and fills it
                    with the contents of the partition that is generated by the
                    specified plug-in name using the data pointed to by the
                    <filename>-r</filename> command-line option or the
                    equivalent rootfs derived from the <filename>-e</filename>
                    command-line option.
                    Exactly what those contents and filesystem type end up
                    being are dependent on the given plug-in implementation.
                    </para>

                    <para>If you do not use the <filename>--source</filename>
                    option, the <filename>wic</filename> command creates an
                    empty partition.
                    Consequently, you must use the <filename>--size</filename>
                    option to specify the size of the empty partition.
                    </para></listitem>
                <listitem><para>
                    <emphasis><filename>--ondisk</filename> or <filename>--ondrive</filename>:</emphasis>
                    Forces the partition to be created on a particular disk.
                    </para></listitem>
                <listitem><para>
                    <emphasis><filename>--fstype</filename>:</emphasis>
                    Sets the file system type for the partition.
                    Valid values are:
                    <itemizedlist>
                        <listitem><para>
                            <filename>ext4</filename>
                            </para></listitem>
                        <listitem><para>
                            <filename>ext3</filename>
                            </para></listitem>
                        <listitem><para>
                            <filename>ext2</filename>
                            </para></listitem>
                        <listitem><para>
                            <filename>btrfs</filename>
                            </para></listitem>
                        <listitem><para>
                            <filename>squashfs</filename>
                            </para></listitem>
                        <listitem><para>
                            <filename>swap</filename>
                            </para></listitem>
                    </itemizedlist>
                    </para></listitem>
                <listitem><para>
                    <emphasis><filename>--fsoptions</filename>:</emphasis>
                    Specifies a free-form string of options to be used when
                    mounting the filesystem.
                    This string will be copied into the
                    <filename>/etc/fstab</filename> file of the installed
                    system and should be enclosed in quotes.
                    If not specified, the default string is "defaults".
                    </para></listitem>
                <listitem><para>
                    <emphasis><filename>--label label</filename>:</emphasis>
                    Specifies the label to give to the filesystem to be made on
                    the partition.
                    If the given label is already in use by another filesystem,
                    a new label is created for the partition.
                    </para></listitem>
                <listitem><para>
                    <emphasis><filename>--active</filename>:</emphasis>
                    Marks the partition as active.
                    </para></listitem>
                <listitem><para>
                    <emphasis><filename>--align (in KBytes)</filename>:</emphasis>
                    This option is a Wic-specific option that says to start a
                    partition on an <replaceable>x</replaceable> KBytes
                    boundary.
                    </para></listitem>
                <listitem><para>
                    <emphasis><filename>--no-table</filename>:</emphasis>
                    This option is a Wic-specific option.
                    Using the option reserves space for the partition and
                    causes it to become populated.
                    However, the partition is not added to the partition table.
                    </para></listitem>
                <listitem><para>
                    <emphasis><filename>--extra-space</filename>:</emphasis>
                    This option is a Wic-specific option that adds extra space
                    after the space filled by the content of the partition.
                    The final size can go beyond the size specified by the
                    <filename>--size</filename> option.
                    The default value is 10 Mbytes.
                    </para></listitem>
                <listitem><para>
                    <emphasis><filename>--overhead-factor</filename>:</emphasis>
                    This option is a Wic-specific option that multiplies the
                    size of the partition by the option's value.
                    You must supply a value greater than or equal to "1".
                    The default value is "1.3".
                    </para></listitem>
                <listitem><para>
                    <emphasis><filename>--part-type</filename>:</emphasis>
                    This option is a Wic-specific option that specifies the
                    partition type globally unique identifier (GUID) for GPT
                    partitions.
                    You can find the list of partition type GUIDs at
                    <ulink url='http://en.wikipedia.org/wiki/GUID_Partition_Table#Partition_type_GUIDs'></ulink>.
                    </para></listitem>
                <listitem><para>
                    <emphasis><filename>--use-uuid</filename>:</emphasis>
                    This option is a Wic-specific option that causes Wic to
                    generate a random GUID for the partition.
                    The generated identifier is used in the bootloader
                    configuration to specify the root partition.
                    </para></listitem>
                <listitem><para>
                    <emphasis><filename>--uuid</filename>:</emphasis>
                    This option is a Wic-specific option that specifies the
                    partition UUID.
                    </para></listitem>
            </itemizedlist>
        </para>
    </section>

    <section id='command-bootloader'>
    <title>Command: bootloader</title>

        <para>
            This command specifies how the bootloader should be configured and
            supports the following options:
            <note>
                Bootloader functionality and boot partitions are implemented by
                the various <filename>--source</filename> plug-ins that
                implement bootloader functionality.
                The bootloader command essentially provides a means of
                modifying bootloader configuration.
            </note>
            <itemizedlist>
                <listitem><para>
                    <emphasis><filename>--timeout</filename>:</emphasis>
                    Specifies the number of seconds before the bootloader times
                    out and boots the default option.
                    </para></listitem>
                <listitem><para>
                    <emphasis><filename>--append</filename>:</emphasis>
                    Specifies kernel parameters.
                    These parameters will be added to the syslinux
                    <filename>APPEND</filename> or <filename>grub</filename>
                    kernel command line.
                    </para></listitem>
                <listitem><para>
                    <emphasis><filename>--configfile</filename>:</emphasis>
                    Specifies a user-defined configuration file for the
                    bootloader.
                    You can provide a full pathname for the file or a file that
                    exists in the <filename>canned-wks</filename> folder.
                    This option overrides all other bootloader options.
                    </para></listitem>
            </itemizedlist>
        </para>
    </section>
</chapter>
<!--
vim: expandtab tw=80 ts=4
-->