| # GDM Custom Configuration file. |
| # |
| # This file is the appropriate place for specifying your customizations to the |
| # GDM configuration. If you run gdmsetup, it will automatically edit this |
| # file for you and will cause the daemon and any running GDM GUI programs to |
| # automatically update with the new configuration. Not all configuration |
| # options are supported by gdmsetup, so to modify some values it may be |
| # necessary to modify this file directly by hand. |
| # |
| # This file overrides the default configuration settings. These settings |
| # are stored in the GDM System Defaults configuration file, which is found |
| # at the following location. |
| # |
| # /usr/share/gdm/defaults.conf. |
| # |
| # This file contains comments about the meaning of each configuration option, |
| # so is also a useful reference. Also refer to the documentation links at |
| # the end of this comment for further information. In short, to hand-edit |
| # this file, simply add or modify the key=value combination in the |
| # appropriate section in the template below this comment section. |
| # |
| # For example, if you want to specify a different value for the Enable key |
| # in the "[debug]" section of your GDM System Defaults configuration file, |
| # then add "Enable=true" in the "[debug]" section of this file. If the |
| # key already exists in this file, then simply modify it. |
| # |
| # Older versions of GDM used the "gdm.conf" file for configuration. If your |
| # system has an old gdm.conf file on the system, it will be used instead of |
| # this file - so changes made to this file will not take effect. Consider |
| # migrating your configuration to this file and removing the gdm.conf file. |
| # |
| # If you hand edit a GDM configuration file, you can run the following |
| # command and the GDM daemon will immediately reflect the change. Any |
| # running GDM GUI programs will also be notified to update with the new |
| # configuration. |
| # |
| # gdmflexiserver --command="UPDATE_CONFIG <configuration key>" |
| # |
| # e.g, the "Enable" key in the "[debug]" section would be "debug/Enable". |
| # |
| # You can also run gdm-restart or gdm-safe-restart to cause GDM to restart and |
| # re-read the new configuration settings. You can also restart GDM by sending |
| # a HUP or USR1 signal to the daemon. HUP behaves like gdm-restart and causes |
| # any user session started by GDM to exit immediately while USR1 behaves like |
| # gdm-safe-restart and will wait until all users log out before restarting GDM. |
| # |
| # For full reference documentation see the gnome help browser under |
| # GNOME|System category. You can also find the docs in HTML form on |
| # http://www.gnome.org/projects/gdm/ |
| # |
| # NOTE: Lines that begin with "#" are considered comments. |
| # |
| # Have fun! |
| |
| [daemon] |
| |
| [security] |
| |
| [xdmcp] |
| |
| [gui] |
| |
| [greeter] |
| |
| [chooser] |
| |
| [debug] |
| |
| # Note that to disable servers defined in the GDM System Defaults |
| # configuration file (such as 0=Standard, you must put a line in this file |
| # that says 0=inactive, as described in the Configuration section of the GDM |
| # documentation. |
| # |
| [servers] |
| |
| # Also note, that if you redefine a [server-foo] section, then GDM will |
| # use the definition in this file, not the GDM System Defaults configuration |
| # file. It is currently not possible to disable a [server-foo] section |
| # defined in the GDM System Defaults configuration file. |
| # |