| Patrick Williams | b48b7b4 | 2016-08-17 15:04:38 -0500 | [diff] [blame^] | 1 | # GDM Custom Configuration file. |
| 2 | # |
| 3 | # This file is the appropriate place for specifying your customizations to the |
| 4 | # GDM configuration. If you run gdmsetup, it will automatically edit this |
| 5 | # file for you and will cause the daemon and any running GDM GUI programs to |
| 6 | # automatically update with the new configuration. Not all configuration |
| 7 | # options are supported by gdmsetup, so to modify some values it may be |
| 8 | # necessary to modify this file directly by hand. |
| 9 | # |
| 10 | # This file overrides the default configuration settings. These settings |
| 11 | # are stored in the GDM System Defaults configuration file, which is found |
| 12 | # at the following location. |
| 13 | # |
| 14 | # /usr/share/gdm/defaults.conf. |
| 15 | # |
| 16 | # This file contains comments about the meaning of each configuration option, |
| 17 | # so is also a useful reference. Also refer to the documentation links at |
| 18 | # the end of this comment for further information. In short, to hand-edit |
| 19 | # this file, simply add or modify the key=value combination in the |
| 20 | # appropriate section in the template below this comment section. |
| 21 | # |
| 22 | # For example, if you want to specify a different value for the Enable key |
| 23 | # in the "[debug]" section of your GDM System Defaults configuration file, |
| 24 | # then add "Enable=true" in the "[debug]" section of this file. If the |
| 25 | # key already exists in this file, then simply modify it. |
| 26 | # |
| 27 | # Older versions of GDM used the "gdm.conf" file for configuration. If your |
| 28 | # system has an old gdm.conf file on the system, it will be used instead of |
| 29 | # this file - so changes made to this file will not take effect. Consider |
| 30 | # migrating your configuration to this file and removing the gdm.conf file. |
| 31 | # |
| 32 | # If you hand edit a GDM configuration file, you can run the following |
| 33 | # command and the GDM daemon will immediately reflect the change. Any |
| 34 | # running GDM GUI programs will also be notified to update with the new |
| 35 | # configuration. |
| 36 | # |
| 37 | # gdmflexiserver --command="UPDATE_CONFIG <configuration key>" |
| 38 | # |
| 39 | # e.g, the "Enable" key in the "[debug]" section would be "debug/Enable". |
| 40 | # |
| 41 | # You can also run gdm-restart or gdm-safe-restart to cause GDM to restart and |
| 42 | # re-read the new configuration settings. You can also restart GDM by sending |
| 43 | # a HUP or USR1 signal to the daemon. HUP behaves like gdm-restart and causes |
| 44 | # any user session started by GDM to exit immediately while USR1 behaves like |
| 45 | # gdm-safe-restart and will wait until all users log out before restarting GDM. |
| 46 | # |
| 47 | # For full reference documentation see the gnome help browser under |
| 48 | # GNOME|System category. You can also find the docs in HTML form on |
| 49 | # http://www.gnome.org/projects/gdm/ |
| 50 | # |
| 51 | # NOTE: Lines that begin with "#" are considered comments. |
| 52 | # |
| 53 | # Have fun! |
| 54 | |
| 55 | [daemon] |
| 56 | |
| 57 | [security] |
| 58 | |
| 59 | [xdmcp] |
| 60 | |
| 61 | [gui] |
| 62 | |
| 63 | [greeter] |
| 64 | |
| 65 | [chooser] |
| 66 | |
| 67 | [debug] |
| 68 | |
| 69 | # Note that to disable servers defined in the GDM System Defaults |
| 70 | # configuration file (such as 0=Standard, you must put a line in this file |
| 71 | # that says 0=inactive, as described in the Configuration section of the GDM |
| 72 | # documentation. |
| 73 | # |
| 74 | [servers] |
| 75 | |
| 76 | # Also note, that if you redefine a [server-foo] section, then GDM will |
| 77 | # use the definition in this file, not the GDM System Defaults configuration |
| 78 | # file. It is currently not possible to disable a [server-foo] section |
| 79 | # defined in the GDM System Defaults configuration file. |
| 80 | # |